HDMI Audio Extractor with Power Amplifier 1.0 Introduction The VSA-X21 is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. It provides an additional line-level stereo audio input that can mix with the HDMI audio. Volume can be controlled using front panel buttons, RS- 232 commands, WebGUI, Telnet, or via an external rotary digital encoder.
Compact, Rugged, Reliable, and Economical Made in the USA 2.1 Package Contents Qty (1) VSA-X21 Qty (1) 48V DC Universal DC Power Adapter Qty (1) User’s Manual Qty (1) Type A to Mini-B USB cable Qty (1) 4 Position Screw Terminal Strip...
HDMI Audio Extractor with Power Amplifier 3.0 Setup 3.1 Installation Connect an HDMI compatible source signal to the HDMI IN connector. Optionally, connect the HDMI display device to the HDMI OUT connector. A display device is NOT required for audio only applications. ...
VSA-X21 4.0 Operation The following is a functional block diagram of the audio routing in the VSA-X21: Figure 2 – Audio Routing and Processing Diagram 4.1 Front Panel Figure 3 - Front Panel MUTE Press this button to mute the output audio. When the unit is muted, the LED glows.
Page 8
When the AUTO LED is on when AUTO MODE has been activated. This means the VSA-X21 can switch to an active INPUT and optionally transmit RS- 232 ON and OFF strings to an external device (like a projector or LCD).
VSA-X21 Connect the supplied USB cable to a compatible Windows™ PC using for use with the Software GUI available for download from http://www.hallresearch.com. 4.2 Rear Panel Figure 3 – Rear Panel HDMI IN Connect the HDMI connector to a compatible video source. (e.g., such as a DVD or Blu- ray player).
HDMI Audio Extractor with Power Amplifier VOL Control / PAGE Sense Terminals These 3 terminal strip connections have different purposes based on the system configuration. For VOLUME Control Connect a compatible rotary encoder (Model UI-KNOB-DP) to the CW, CCW and GND terminals for system volume control.
AC cord has a ground prong). If the preamp does not provide a balanced (differential) output, you should not tie the return of your source to the ground of the VSA-X21. Doing so would create a ground loop that will most likely cause audio hum.
HDMI Audio Extractor with Power Amplifier 4.6 L/R Speaker Connections NOTE The audio amplifier is designed to drive loads equal to or greater than 8 Ω Using lower loads may cause an over-current shutdown of the audio amplifier, this will be detected and the amplifier will be reset. Audio output from the amplifier will mute during this time.
VSA-X21 5.0 Serial Commands The following table lists the RS-232 commands: o A single carriage return character (0x0D) must terminate each command. o Invalid input, spaces and line feeds characters (0x0A) are ignored. RS-232 communication on the RS-232 IN terminal strip is: o 9600 bps, 8 Bit, No Parity, 1 Stop bit.
Page 14
HDMI Audio Extractor with Power Amplifier Response Command Function and Example VDNxx VOLxx<CR> Controls Audio output level. Optional range is 0 to 100%. VDN<CR> – Adjust volume level down 2% VDN10<CR> – Adjust volume level down 10% VCx<CR> Controls current volume control setting VC?<CR>...
Page 15
VSA-X21 Response Command Function and Example MOx<CR> Controls the MONO/STEREO Status MO?<CR> – Query current MONO/Stereo Setting MO1<CR> – Turn on MONO MO0<CR> – Turn off MONO (Stereo) (Factory Default) FPx<CR> Controls the Front Panel Lock Status FP?<CR> – Query current Front Panel Lock Setting FP1<CR>...
Page 16
HDMI Audio Extractor with Power Amplifier Response Command Function and Example SB? or SBxxx.xxx.xxx.xxx<CR> Controls Subnet Mask setting |SBx SB?<CR> – Query current Subnet Mask |SB255.255.255.000<CR> - Set the Subnet Mask to 255.255.255.000 Note: Setting takes effect when Gateway address is set GW? or GWxxx.xxx.xxx.xxx<CR>...
Page 17
VSA-X21 Response Command Function and Example PGx<CR> Controls the Encoder/Page Sensor Setting PG?<CR> – Query current Encoder/Page Sensor setting PG0<CR> – Rotary Encoder (Factory Default) PG1<CR> – Page Sensor (Model VSA-PGSNS) PG2<CR> – Contact Closure (CW & GND) Note: Using the Rotary Encoder or Page Sensor will disable the ability to use the PAGE SENSE (CW &...
Page 18
HDMI Audio Extractor with Power Amplifier Response Command Function and Example WPx<CR> UHBX-SW3-WP/S Installed Selection WP?<CR> – Query current UHBX-SW3-WP/S Installed selection WP1<CR> – UHBX-SW3-WP/S Installed WP0<CR> – UHBX-SW3-WP/S NOT Installed UIx<CR> X21-UI Installed Selection UI?<CR> – Query current X21-UI Installed selection UI1<CR>...
Page 19
VSA-X21 Response Command Function and Example BGx,y<CR> Button Group Selection Button x = 0 thru 7 Button Group y = 0 thru 8 0 = NO GROUP, 1 thru 8 separate groups available BG?<CR> – Query current all button group states BGx?<CR>...
Using this feature disables the use of a Rotary Encoder or Page Sensor. 5.3 Device Addressing The model VSA-X21 units have the ability to daisy chain the RS-232 IN and RS-232 OUT together with other units and have a serial controller at the head of the chain be able to access all the units in the chain.
Page 21
VSA-X21 For example: With any number of units daisy chained together and factory default setting of “0” for a device address, sending a “PW1” command will result in all units powering on. RS-232 Controller connected to Unit #1 RS-232 IN ...
HDMI Audio Extractor with Power Amplifier 6.0 WebGUI and Telnet Operation The VSA-X21 has a built-in webpage that can control the basic functions of this model via a compatible LAN Network. The webpage has buttons and indicators that show the state of that feature.
It uses a non-invasive sensor that monitors existing PA lines without having to splice into the wires. The sensor detects when an external PA system has activated and sends a signal to the VSA-X21 to mute the audio. Once the external PA line goes quiet, the VSA- X21 will resume audio output.
The sensitivity is related to the number of turns used. Connect the leads on the sensor to the VSA-X21 terminals labeled “SENSE” (CW and CCW). Connect white to CW (+) and black to CCW (-) terminals. ...
VSA-X21 9.0 Troubleshooting If you are experiencing problems getting the VSA-X21 to work properly, please use the following troubleshooting suggestions. Make sure that all of the connections are solid. Loose connections are the number one cause of issues. ...
(32mm H x 229mm W x 109mm D) Depth excludes connectors Product weight Amplifier 1.5 lbs Kit (shipping) 4.2 lbs includes: VSA-X21, power supply w/cord, USB cable, terminal strips, users manual, and packaging Vibration ISTA 1A in carton (International Safe Transit Association) Safety...