Advertisement
CHANGING
10. Pry
the
plug
cover
from
the
plastic
bushing
at the top of the lower
door
and
press into
the p_astic bushing
on
REVF_P,:SI
BLE
the opposite
side of the door.
DOOES
11. Remove
the base grille
by grasping
at
both ends and pulling it straight
out.
This refrigerator
has been
built with
the
12. Remove the lower hinge and spacer.
doors
hinged
on the right.
If you wish
to
hinge the doors on the left, follow
these in-
13, Rotate
the
lower
hinge
counterclock-
structions.
If it becomes
necessary
to return
wise
90 °
and
install
it
(including
the hinges
to the right
side, merely
trans-
spacer)
to the left leg of the cabinet.
pose
all references
to "right"
and
"left"
when following
these instructions.
NOTE: It will take extra effort
to install the
screws.
The
screws
are self tapping
and
TOOLS
REQUIRED
will have to cut threads in the screw holes.
Phillips screwdriver
End wrench
(5/16")
_'--_
_
JL""=
_
_K_
Hex-head
socket screwdriver
(5/16")
Table knife
i---_ _
O]
CHANGING
DOORS
1. Turn the fresh food
control
to OFF and
O
remove all food
from the interior.
O
2. Remove
the
handles
from
1he doors
I
and set aside. On the side of the doors
that
you are gotng
to install
the han-
dles,
remove
the
small
round
screw
14. Pull the metal
hinge
pin from
the side
ho_e plugs with a table knife and press
of the
lower
hinge
and
place
it, in-
them
into
the holes
on the
opposite
ctuding
the spacer
washer,
intothetop
side of the doors,
hole.
3. Using
a socket
screwdriver
or
end
15. Pry out the two
screw
hole
plug
but*
wrench,
remove
the screws from the up-
per hinge. Carefully
lift the door (includ-
tons on the bottom
left side of the top
door and lower
door. Remove
the door
ing upper
hinge)
off the center
hinge
stops
(metal
plate)
on the
bottom
of
and place it on a padded
surface to pre-
each door and install them on opposite
vent scratching.
Avoid
losing the spacer
sides.
Press in the plug buttons
in the
that was between
the hinge and the cab-
holes on the right side of both doors.
inet top.
16. Set
the
lower
door
on
the
bottom
4. Using
a table
knife,
pry the plug
but-
hinge,
making
sure
the
hinge
pin
ton
cover
from the
plastic
bushing
at
enters the bushing in the door bottom.
the
top
of the
door.
Save
the cover
17. While
holding
the
door
in a closed
for future
use.
position,
take the center
hinge pin that
was
removed
in step
8, and insert
it
5. Lift
the
upper
hinge
and
the
spacer
through
the
_eft hote
of
the
center
washers
from
the
door
and
install
hinge
and into the bottom
door bush-
them
at the opposite
corner,
ing. Make
sure the long pin goes
into
the
bottom
door
and
the
short
pin
6. Position
the ptug button
cover,
saved
goes into the top door.
from
step 4, over
the old hinge
bush-
18. Set
the
upper
door
on
the
center
ing and press it into place,
hinge,
making
sure
the
hinge
pin
enters
the
door
bushing.
When
you
7. Pry
out
the
3
plastic
plug
buttons
close this door, the gasket
should
hold
from
the cabinet
top and
press them
it in place.
into the opposite
corner.
19. Making
sure
to use the same number
8. Lift
the
center
hinge
pin
out
of the
of
spacers
that
were
originally
used
bottom
door
and center
hinge.
Care-
beneath
the
upper
hinge,
install
the
fully
lift the lower
door
off the lower
hinge
mounting
screws.
Before
tight-
hinge
and
place
it on a padded
sur-
ening
these screws,
make sure the top
face.
If the metal
hinge
pin
pulls out
of the door
is level
with
the
cabinet
of the
lower
hinge
when
the door
is
top, and the space
between
the door
removed,
pull it out of the
door
bot-
is eguidistant
across
the
entire
front.
tom and press it back into the hinge.
Avoid
over-tightening
these
screws.
Tighten
both
until
they
are just snug,
then
turn
them
in
another
one-half
9. Remove
the
center
hinge
and spacer
turn.
from
the
cabinet.
Transfer
the
two
screws
from the left end of the divider
20. Examine
the
door
gasket
all around
bar to the right end. Install
the center
each
door,
making
sure
no gaps
are
hinge
and spacer
on the
left
end
of
visible
between
the
gasket
and cabi-
the divider
bar the same way
it was
net. If a gap shows,
try stretching
the
installed
on
the
right
end.
Tighten
gasket
away
from
the
door
so the
both screws
until they
are just snug,
magnet
will
contact
the
cabinet
sur-
then turn them one-half turn more.
face.
Advertisement
