Table of Contents
Advertisement
Quick Links
In the Swim® Solar/Battery Powered Solar Blanket Reel
Installation / Operation Guide
INTRODUCTION
Save this Instruction Manual.
Please Read, Follow, and
In the Swim® Solar/Battery Powered Solar Blanket Reel is recommended for use on rectangular
shaped pools with or without diving boards.
The In the Swim® Solar/Battery Powered Solar Blanket Reel system should only be used for the
intended application.
PBITS001
Advertisement
Table of Contents
Summary of Contents for In the Swim Automatic Solar Blanket Reel System
- Page 1 In the Swim® Solar/Battery Powered Solar Blanket Reel is recommended for use on rectangular shaped pools with or without diving boards. The In the Swim® Solar/Battery Powered Solar Blanket Reel system should only be used for the intended application. PBITS001...
-
Page 2: Important Safety Precautions
IMPORTANT SAFETY PRECAUTIONS READ AND FOLLOW ENTIRE INSTRUCTION MANUAL AND ALL PRECAUTIONS, PRIOR TO INSTALLING, USING, OR TROUBLESHOOTING THIS EQUIPMENT. • Read, follow, and save the entire instruction manual • Use the system only in the intended manner. • Remember, solar blankets are not safety covers. •... -
Page 3: Getting Started
GETTING STARTED Required Tools: • 5/16 & 7/16 wrenches or sockets • #2 Phillips screwdriver • Drill • 1/4” and 5/32” drill bits • Flat blade screwdriver Select the Location Select a location at one of the narrow ends of the pool. The location must be away from the ladder. Typical Layout... -
Page 4: Installation
Installation 1) Position the Stands Position the stands in the selected location at one of the narrow ends of the pool. The stands come assembled in the middle of the height adjustment range. Height adjustment The height of the reel system is adjustable through a wide range. The height of the cross tube can be changed by moving the hub assemblies to different height settings. - Page 5 Example- Highest Setting Example- Lowest Setting Adjusting Stand Height 1. Remove the drive and idler stand covers. The covers are each held in place by three screws. 2. Remove bolts that attach motor case to stand. Position motor / gearbox assembly at the desired height.
- Page 6 Drive Stand Using a 5/16 wrench, remove (4) mounting bolts. Adjust stand height and reinstall bolts. Idler Stand Using a 7/16 wrench, remove (4) mounting bolts. Adjust stand height and reinstall bolts.
- Page 7 2) Installing Cross Tubes The cross tube assembly is adjustable to accommodate required widths from 17 to 23.5 feet. The cross tube assembly has three tube sections. Two smaller tubes telescope from each end of the larger diameter tube. 1. Slide a smaller diameter tube section into each end of the large tube. 2.
- Page 8 Attaching the cross tube assembly to the hub assemblies. 1. Insert the drive and idler hubs into the cross tube 2. Drill a 5/32 pilot hole through the tube and into the hub approx ¾” 3. Insert the screw and tighten...
- Page 9 3) Installing battery, solar charger and antenna Installing the battery The battery is simply placed inside of the drive side stand on the right hand side (opposite side from the controller). The connector from the battery is then plugged into the mating connector in the drive side stand.
- Page 10 4) Test Run With the cross tube attached, test run the system. (See the OPERATION Section for instructions.) Ensure the cross tube is securely attached to the hubs and that it runs smoothly without wobble. In preparation for installing the solar blanket, observe the direction of rotation of the cross tube. Compare this direction of rotation to the EXTEND and RETRACT buttons on the remote control as well as to the direction you plan to wrap the solar blanket around the cross tube.
- Page 11 5) Install the covers for the drive and idler stands Install the drive stand cover. Make sure the motor harness is routed through the slot in the side of the cover. If the idler stand cover was removed, reinstall it at this time. 6) Attach the solar blanket Attach solar blanket onto the cross tube in the manner prescribed by the blanket/ blanket strap manufacturer.
- Page 12 Safety Items prior to operation Visually inspect the pool prior to retracting or extending the solar blanket. The pool should be clear of occupants or other items that might conflict with the solar blanket. When not in use, store the remote control in a secure location in order to prevent unauthorized operation.
-
Page 13: Manual Override
MANUAL OVERRIDE In the event of a loss of power, a manual override is provided. 1) Remove the cover of the drive stand 2) Unplug the motor harness at the motor connector. 3) Remove the cover of the idler stand. 4) Use a ¾-inch wrench or socket to turn the reel in the desired direction. -
Page 14: Seasonal Storage
Maintenance and Troubleshooting Stands and tubes The stands and tubes are designed to be weather resistant and maintenance free. The hubs are made of a special material that does not require lubrication. The stands are specially coated to resist the elements and may be cleaned using a mild soap and water solution. The use of a pressure washer is to be avoided due to the battery and other components inside of the drive stand. -
Page 15: Fcc Statement
FCC Statement © 2009 TouchTronics, Inc. All Rights Reserved. TouchTronics, the TouchTronics logo, and other TouchTronics marks are owned by TouchTronics and may be registered. TouchTronics assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice. FCC Compliance and Advisory Statement. -
Page 16: Warranty
WARRANTY DAYS CORPORATION LIMITED WARRANTY, REPLACEMENT PARTS & RETURNS POLICY LIMITED WARRANTY Effective January 1, 2016 Days Corporation (“Days”) warrants to the original purchaser of system components (the “Products”), for a period of three (3) years from the original sale date or date of dealer installation, whichever is earlier (“Limited Warranty Period”), that the Products shall be free from defects in material and workmanship.