Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Media 22E-24E
- Page 1 USE AND MAINTENANCE MANUAL MEDIA 22E-24E ED. 07-2010 Doc. 10025342 Ver.
- Page 2 Le descrizioni contenute nella presente pubblicazione non si intendono impegnative. L’azienda pertanto, si riserva il diritto di apportare in qualunque momento, le eventuali modifiche ad organi, dettagli, forniture di accessori, che essa ritiene convenienti per un miglioramento o per qualsiasi esigenza di carattere costruttivo o commerciale. La riproduzione anche parziale dei testi e dei disegni, contenuti nella presente pubblicazione, è...
-
Page 3: Table Of Contents
SUMMARY ON CONSIGNMENT OF THE MACHINE ........................4 INTRODUCTORY COMMENT .............................4 TECHNICAL DATA ..............................4 SYMBOLOGY USED ON THE MACHINE........................5 SYMBOLOGY USED IN THE MANUAL........................7 MACHINE PREPARATION............................8 1. HANDLING OF THE PACKED MACHINE ..........................8 2. HOW TO UNPACK THE MACHINE............................8 3. -
Page 4: On Consignment Of The Machine
We therefore suggest you to read this instruction booklet carefully and re-read it whenever difficulties arise in the course of machine use. Our Service Department is at your disposal for all such advice and servicing as may prove necessary. MEDIA 22E MEDIA 24E TECHNICAL DATA U.M. 10200041... -
Page 5: Symbology Used On The Machine
SYMBOLOGY USED ON THE MACHINE Indicates the general switch 0 / 1 Indicates the warning light for the presence of the voltage Symbol denoting cock Indicates the cock lever Indicates the solenoid valve switch Symbol denoting up-down brush base Indicates the lever of the brush base lifting Symbol denoting brush Indicates the switch of the brush motor Symbol denoting suction motor... - Page 6 SYMBOLOGY USED ON THE MACHINE Indicates the exhaust pipe of the recovery tank Indication of the maximum temperature of the solution detergent Placed near the charging hole of the solution tank Symbol denoting the coupling Indicates the anchor points and the load direction Symbol denoting the open book Indicates that, the operator has to read the manual before the use of the machine...
-
Page 7: Symbology Used In The Manual
SYMBOLOGY USED IN THE MANUAL Symbol denoting a warning Read carefully the sections preceded by this symbol, for the safety of the operator and of the machine... -
Page 8: Machine Preparation
Do not place more than two packages on top of each other. The total weight is 171 kg for Media22E and 185 kg for Media24E. The overall dimensions are: Media 22E Media 24E A: 1280 mm... -
Page 9: Squeegee Assembly
MACHINE PREPARATION SQUEEGEE ASSEMBLY The squeegee, which is packed separately from the machine, should be assembled as shown in the figure. Insert first the left squeegee pin (1) in the left arm slot, then the right pin (2) into the right slot, paying attention to keep the spring and the washer over the blade of the arm itself. -
Page 10: Adjustment Squeegee Pressure
MACHINE PREPARATION ADJUSTMENT SQUEEGEE PRESSURE The squeegee is already loaded with an appropriate pressure. It is possible to adjust the squeegee pressure through the register (1) shown in the figure. In order to increase pressure, it is necessary to tighten the register. To decrease pressure, it is necessary to unscrew the register. -
Page 11: Recovery Tank
MACHINE PREPARATION RECOVERY TANK Open the cover (1) and check that, the suction connection (2) is properly blocked by fitting the notches into its proper seat rotating it clockwise and that it is connected regularly to the hose which goes to the suction motor. Check furthermore that, the squeegee hose (3) is properly placed in their seats and that the plug of the exhaust pipe, which is located in the rear part of the machine, is closed. -
Page 12: General Rules Of Security
GENERAL RULES OF SECURITY The rules below have to be followed carefully in order to avoid damages to the operator and to the machine. Read the labels carefully on the machine. Do not cover them for any reason and replace them immediately if damaged The machine must be used exclusively by authorized staff that has been instructed for its use During the working of the machine, pay attention to other people and especially to the children... -
Page 13: Performance
PERFORMANCE SETTING FOR WORK 1. Plug into the mains system 2. Turn the key of the general switch (1) into position I (clockwise). Immediately, the signal lamp comes on (2) 3. Press the motor switch (1) 4. Press the solenoid valve switch (2) 5. -
Page 14: Movement
PERFORMANCE MOVEMENT The traction of these machines is obtained through a flat belt put into tension with the lever (1) as indicated in the figure. The movement speed is proportional to the force carried on the lever. ATTENTION! When carrying out even short backward movements, make sure that the squeegee is lifted. -
Page 15: Circuit Breaker
PERFORMANCE CIRCUIT BREAKER The machine is equipped with a circuit breaker placed on the instrument board which interrupts the current to the brush motor, when it exceeds the predetermined load. In order to start up the machine again, press the push button. If the circuit breaker interrupts the current continuously, it is necessary to look for its causes. -
Page 16: On Completion Of The Work
ON COMPLETION OF THE WORK Having finished the job and before any type of maintenance is done: 1. Close the cock through the lever (1) 2. Raise the brush base through the lever (2) 3. Raise the squeegee through the lever (3) 4. -
Page 17: Daily Maintenance
DAILY MAINTENANCE CLEANING RECOVERY TANK 1. Release the hose placed on the rear panel 2. Unscrew the exhaust plug and empty the tank completely ATTENTION! This operation has to be carried out using gloves to protect from contact with dangerous solutions. -
Page 18: Cleaning Suction Filter
DAILY MAINTENANCE CLEANING SUCTION FILTER 1. Lift the cover 2. Take off the suction plug by rotating it counterclockwise 3. Take off the filter with the antifoam protection 4. With a water jet clean the walls and the bottom of the filter 5. -
Page 19: Replacement Front Squeegee Rubber
DAILY MAINTENANCE REPLACEMENT FRONT SQUEEGEE RUBBER If the front squeegee rubber is worn, a good suction is not achieved and therefore the machine does not dry perfectly. In that case proceed as follows with the replacement: 1. Take off the squeegee loosening the register (1) 2. -
Page 20: Weekly Maintenance
WEEKLY MAINTENANCE CLEANING OF THE SQUEEGEE HOSE Weekly or whenever suction seems to be unsatisfactory check that the squeegee hose is not obstructed. Eventually, clean it proceeding as follows: 1. Take off the hose from its coupling on the squeegee 2. -
Page 21: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE INSUFFICIENT WATER ONTO THE BRUSH 1. Make sure that the key (1) is on position I 2. Make sure that the solenoid valve switch is on (2) 3. Make sure that the brush switch is on (3) 4. -
Page 22: Choice And Use Of Brushes
LIST FOR THE CHOICE OF THE BRUSHES Brush ∅ Machine Q.ty Code Bristles type Thick Notes 66802200 66802210 Media 22E 66802220 66802230 ABRASIVE Pad blocking 66702030 Pad holder + Center Lock 66811070 66811050 66811060... -
Page 23: Ec Declaration Of Conformity
Via Ca’ Nova Zampieri no. 5 37057 San Giovanni Lupatoto (VR), Italy declares under its sole responsibility that the SCRUBBING MACHINE mod. MEDIA 22E – MEDIA 24E comply with the requirements of the following Directives: • 2004/108/EC: Electromagnetic Compatibility Directive and subsequent modifications. •...
Need help?
Do you have a question about the 22E-24E and is the answer not in the manual?
Questions and answers