Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Symbol VRC 4000 Series
Summary of Contents for Symbol VRC 4000 Series
- Page 1 RS 2200/3200 Series VRC 4000 Series Installation Guide...
- Page 2 1997 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
- Page 3 It is powered from the vehicle’s electrical system (battery) through a ® choice of two power converters. It uses Symbol’s Spectrum24 2.4 GHz spread-spectrum radio link to communicate with radio frequency (RF) network access points hard-wired into the LAN.
-
Page 4: About This Guide
About This Guide This guide provides basic setup, installation, and maintenance instructions. Topics discussed include: • Parts of the VRC 4000 • Setting up the VRC 4000 • Mounting the bracket assemblies • Mounting the VRC • Attaching the keyboard assembly •... -
Page 5: Parts Of The Vrc
Parts of the VRC Touchscreen Antenna Port Antenna LPT1 COM1 Locking Keyboard Parallel Network Serial Keyboard Speaker Port Connector Port Port Connector Port PCMCIA Card Slot Cover Reset COM2 Mouse Audio Microphone Switch Serial Port Connection Connector Indicator Port... -
Page 6: Mounting The Bracket Assemblies
Set-Up To set up your equipment, first unpack your terminal and accessories, and ensure that the parts shipped match the parts ordered. Keep the shipping container and packing material in case you need to return your computer for repair at a later date. The VRC is factory-equipped with a network interface and the appropriate network software for communicating with the network. -
Page 7: Crown Mounting Assembly
via an access cord. Installation of the VRC 4040 requires mounting the bracket assembly, installing the DC power converter, and attaching the access cord to the vehicle’s electrical system. Caution For proper operation on electric fork lifts, the VRC must be isolated from the chassis. -
Page 8: Universal Mounting Assembly
1. Place the mounting assembly up against the wall or bracket. Make sure assembly is level. 2. Mark location for mounting holes. 3. Drill mounting holes using 13/32” drill bit. 4. Secure mounting bracket to wall using two bolts (3/8” x 16 x 3/4”) and two nuts. -
Page 9: Hyster Mounting Assembly
5. Place the U-shaped bracket over bolts and secure the U- shaped bracket to the assembly using two nuts. 6. Install VRC using procedures in VRC Mounting on page 8. Hyster Mounting Assembly The hyster mounting assembly has an L-shaped bracket at the bottom that permits mounting the bracket onto a flat vertical wall or bracket. -
Page 10: Vrc Mounting
VRC Mounting After the mounting bracket is installed, mount the VRC onto the assembly. To mount the VRC: Bracket Assembly Knob Friction Washer 1. Align mounting holes on the sides of the VRC with the holes on the arms of the mounting assembly. 2. -
Page 11: Keyboard Assembly
Keyboard Assembly The VRC mounting assembly may be configured with or without the keyboard assembly. If the keyboard assembly is not originally configured, it can be added to the mounting assembly at a later time. To mount the keyboard assembly onto the mounting bracket assembly: Bracket Assembly... - Page 12 7. Install VRC using procedures in VRC Mounting on page 8. 8. Connect keyboard cable to connector on rear panel of VRC. Note: The Symbol-supplied ruggedized keyboard has a special locking connector which is designed to en- sure good contact in the high-vibration vehicle mount application.
-
Page 13: Providing Power To The Vrc 4000
Providing Power to the VRC 4000 Power is provided to the VRC 4000 terminal via a locking DC- power adapter, as illustrated below: All cable connections should be made to the VRC 4000 before the system is powered up. Since there is no ON/OFF switch, the VRC 4000 powers up as soon as the power supply connections are completed and the power supply is plugged in to the 110 VAC electrical outlet. -
Page 14: Power Converter
filtered and fused. Never connect the access cable directly to the battery terminals. Possible connection points are at the horn, lights (feed), or ignition switch (feed). 24-48 V Power Converter The electrical harness access cable for the 24-48 V Power converter has two leads at one end which are permanently wired into the vehicle’s electrical system. -
Page 15: Maintenance
mates with a similar connector on the DC power converter’s power input cable. The black harness wire is connected to a positive voltage source. The white harness wire is connected to a negative voltage source. The green or braided lead is connected to chassis ground. -
Page 16: Regulatory Information
Regulatory Information Labeling Symbol Technologies, Inc. Holtsville, NY Net ID: 00A0F8166421 (1P) Model: VRC4040-10C40DUS Y463732 (S) S/N: INDUSTRIAL COMPUTER 16WA LISTED I.T.E. 12 VDC @ 2.5A T h i s d e v i c e c o m p l i e s w i t h P a r t 1 5 o f t h e F C C R u l e s . O p e r a t i o n i s s u b j e c t t o t h e... -
Page 17: Radio Frequency Interference Requirements - Canada
Radio Frequency Interference Requirements This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 18: Ce Marking And European Union Compliance
The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modifications to Symbol Technologies equipment not expressly approved by Symbol Technologies could void the user’s authority to operate the equipment. -
Page 19: Related Publications
This warranty is limited to repair or replacement at Symbol’s option, with reasonable promptness after being returned to Symbol by a carrier selected and paid for by the customer. These provisions do not prolong the original warranty term for any product which has been repaired or replaced by Symbol. - Page 20 This product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No. 4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183;...
Need help?
Do you have a question about the VRC 4000 Series and is the answer not in the manual?
Questions and answers