Table of Contents
Advertisement
Quick Links
Installation Manual for
flipIT- Kit Generation II
FIK-18 keyboard tray actuated flipIT ®
FIH-18 handle actuated flipIT ® without keyboard tray
FIK-19 keyboard tray actuated flipIT ®
FIH-19 handle actuated flipIT ® without keyboard tray
FIK-23 keyboard tray actuated flipIT ®
FIH-23 handle actuated flipIT ® without keyboard tray
How to install into any desktop using templates
for cutting table top and pilot holes.
How to install into factory cut table top
with pilot holes.
ATTENTION:
LCD must be installed in order f or the flipIT lid
to remain closed. The LCD counterbalances
the force of the pneumatic cylinder.
Note:
flipIT 19 and 23 for WideScreens install
as illustrated by the flipIT 18. The width
of the cutout and keyboard are the main
differences. The template(s) provided
work in a similar way. On the flipIT 19
and 23 templates, keyboard pilot holes
are printed on the same template with
the cutout markings. 2 templates are
provided for FIK-19 and 23, one is pro-
vided for the FIH-19 and 23.
G E N E R A T I O N
US Patent Pending
© 2009 CBT Supply Inc.
I I
Advertisement
Table of Contents
Summary of Contents for CBT Supply FIK-18
- Page 1 Kit Generation II Note: flipIT 19 and 23 for WideScreens install FIK-18 keyboard tray actuated flipIT ® as illustrated by the flipIT 18. The width of the cutout and keyboard are the main FIH-18 handle actuated flipIT ® without keyboard tray differences.
-
Page 2: Getting Started
Always use safety glasses and wear proper apparel that won’t get caught in moving parts. CBT Supply, Inc. will not be held liable for misuse of tools and disregard f or power tool manufacturer’s safety precautions. -
Page 3: Planning Ahead
FIK/FIH-23 for widescreens cutout is 15-5/16” x 25” and Keyboard is 26” wide including mouse surface. FIK/FIH-19 for widescreens cutout is 15-5/16” x 20.62” and Keyboard is 26” wide including mouse surface. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc. - Page 4 1/2” or less clear- ance between the monitor and the lid rest flange . Several sets of holes, spaced 1/2” apart, are provided to accommodate LCD variations. See page 14 for setting the clearance. © 2009 CBT Supply Inc.
-
Page 5: Parts And Hardware
& cable release monitor’s screws Qty 1 Paper template for keyboard pilot holes, shown Qty 1 Paper template for top cut-out, shown positioned positioned for use (FIK-18 only) for use. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc. - Page 6 Step 2- Adhere Cutout Template to Desktop Use a glue stick on back of template cut lines. Align front edge of template with desktop centerline and press in place. © 2009 CBT Supply Inc.
- Page 7 You must have the skill to saw a straight line within the toler ance of the width of the saw blade. Saw from corner hole to cor ner hole. Remove the remains of the paper tem- plate when this step is finished. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc.
- Page 8 1/8” holes 3/8” deep using factory specifications. You are the masking tape depth now ready to begin installation gauge you just made. of the flipIT mechanism. Repeat this step for the remaining Pilot Holes. © 2009 CBT Supply Inc.
- Page 9 Using #2 Phillips screwdriver bit, install four ⁄ inch wood screws in the locations shown in the two sides of the assembly. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc.
-
Page 10: Installation Tip
To mark locations for drilling 5 pilot holes, pull the slack out of the cable and place the bracket parallel with the lid. Mark hole locations with pencil. Using 1/8” bit, drill pilot holes using masking tape for a depth gauge. With 5 wood screws, install the handle bracket. © 2009 CBT Supply Inc. - Page 11 Slide pin though cable end. Cables may have a little slack when properly installed. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc.
- Page 12 The VESA mount is a 2-par t assembly. installed The male part is installed on the flipIT lid (right) with 5mm Euro screws. The female half installs on your LCD using the screws from your LCD. © 2009 CBT Supply Inc.
- Page 13 Purchase this kit from the Apple w eb site. Go to the Apple Store and search the ter m VESA adapter. The iMac® products’ drive location does not per mit use with flipIT. flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc.
- Page 14 Additional sets of mounting holes, your monitor may be lighter weight than expected. A less powerful pneumatic cylinder may set 1/2” apart, are provided to solve this problem. Contact CBT Supply. achieve the ideal position. © 2009 CBT Supply Inc.
- Page 15 Arm Catch Assembly 27919 Pneumatic Cylinder 27898 Keyboard Tray / Slide Assembly (FIK only) 27892 Flat Screen Tilt Assembly 27884 Bracket / Screw Package 28193 Top Lid 28163 Euro Screw flipIT Tech Line: 800 770-7042 © 2009 CBT Supply Inc.
-
Page 16: Parts Identification
Wood Screw (21486) (8) G E N E R A T I O N US Patent Pending CBT Supply, Inc.’s patented flipIT Integrated LCD Workstation has been designed ® and tested to perform as an ergonomically correct, space sa ving unit.