1. Manuals
  2. Brands
  3. Bond Manuals
  4. Electric Heater
  5. HYUHI10000-1
  6. Owner's manual

Bond HYUHI10000-1 Owner's Manual

Tablemount induction heater
Hide thumbs

Advertisement

Table of Contents

TABLEMOUNT INDUCTION HEATER
50226
Item#
Model# HYUHI10000-1
Note: A table with an umbrella hole (not included)
is required to assemble this product.
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the owner's manual thoroughly before installing or servicing this
result causing property damage, personal injury or loss of life.
Save these instructions for future use. If
you are assembling this unit for someone
else, give this manual to him or her to
read and save for the future.
Owner's Manual
DANGER
If you smell gas:
1. Shut off gas to the appliance.
3. If odor continues, keep away from
the appliance and immediately call
WARNING
Do not store or use gasoline or other
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
WARNING
For outdoor use only.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HYUHI10000-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bond HYUHI10000-1

  • Page 1 TABLEMOUNT INDUCTION HEATER 50226 Item# Model# HYUHI10000-1 DANGER If you smell gas: 1. Shut off gas to the appliance. 3. If odor continues, keep away from the appliance and immediately call WARNING Do not store or use gasoline or other vicinity of this or any other appliance.

  • Page 2: Safety Information

    Once you have a flame started, hold down the control knob for 1 minute. • Do not add water into the unit. • Do not operate unit if any part has been under water. Call a service technician to replace any Bond Manufacturing Company | Page 2...
  • Page 3 Bond Manufacturing Co. Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance. For assistance with repair or replacement of the burner or any other parts, calls Bond Manufacturing at 1.866.771.2663.
  • Page 4 Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any parts are missing or damaged, do not attempt to assemble the product. Bond Manufacturing Company | Page 4...
  • Page 5 CONTENTS Item Description Reflector assembly Control box and mesh guard assembly Glass tube Gas hose Fixing Nut(preassembled) Tank Holder Electronic Igniter 1-866-771-2663 | Page 5...
  • Page 6 Be sure to fully tighten. 3. Check that the ignition control knob (J) for the gas supply system is turned to the "OFF" position. Bond Manufacturing Company | Page 6...
  • Page 7 4. Unscrew and remove the cap on the electronic igniter (K), then place the battery AAA (H) into the battery slot. Be sure the positive side of the battery face outwards. Replace the electronic igniter cap over the battery, be sure to tighten securely.
  • Page 8 8. Put the 20 lb. propane gas tank (not included) into the tank holder ( I ). Turn the wing screw on the outside of the tank holder ( I ) clockwise to tighten the tank into the tank holder. Bond Manufacturing Company | Page 8...
  • Page 9 9. Turn the cylinder valve on the tank clockwise to close the propane tank. PRESSURE Attach the regulator to the cylinder valve RELIEF VALVE by turning the regulator coupling nut CYLINDER VALVE BLEED-OFF clockwise. Make sure it is fastened BLACK COUPLING NUT VALVE securely and tighten connections by hand turn clockwise to connect...

  • Page 10: Operation

    If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is is repaired. LIGHTING INSTRUCTIONS Press and turn the ignition control knob Bond Manufacturing Company | Page 10...

  • Page 11: Maintenance

    MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down.

  • Page 12: Warranty

    • Use and installation other than what is listed in this manual. Please contact the manufacturer for replacement parts. CONTACT If you have any questions or concerns, please contact Bond Manufacturing Company at the below resources: Toll Free Phone 1-866-771-BOND (2663) | Monday - Friday, 8am - 4:30pm PST Email customer.service@bondmfg.com...

Table of Contents