Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Thermal Solutions VMW12PFA03-48018-R11
- Page 1 User Manual Rugged Display Computer – 12” RC6600 Rugged iPC VMW12PFA03-48018-R11...
-
Page 2: Table Of Contents
Contents Safety Information ........................4 Important Information ......................... 5 1 Introduction ..........................8 1.1 Product Features ........................8 1.2 Packing List ........................... 9 1.3 Appearance ........................10 1.4 Characteristics ........................11 1.5 Dimensions ......................... 12 1.6 Exploded Drawing ......................13 2 Getting Started........................ - Page 3 5 Driver Installation ........................29 5.1 ELO AccuTouch/ CarrollTouch Infrared Driver Installation ..........29 5.1.1 Downloading Drivers ....................29 5.1.2 Configuration Utility ....................30 5.2 The Premier Touch Driver Installation ................32 5.2.1 Installing Touch Kit ....................32 5.2.2 Configuration Utility ....................33 6 Troubleshooting ........................
-
Page 4: Safety Information
Safety Information Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. -
Page 5: Important Information
user’s manual. o The equipment has been dropped and damaged. o The equipment has obvious signs of breakage. Do not leave this equipment in an uncontrolled environment where the storage temperature is below -20° C (-4°F) or above 60° C (140° F). It may damage the equipment. - Page 6 Copyright Notice No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.
- Page 7 on the installation and operation of any of our products. Please do not hesitate to call or e-mail us. Pro-face America contact information, please go to http://www.profaceamerica.com...
-
Page 8: Introduction
1 Introduction Rugged Display Computer with fan-less, low power but high performance platform design, sunlight readable panel, WLAN integration, great ability for anti-shock & vibration, IP65 protection and anti-corrosion coating with aluminum alloy housing. Both of great mobility and robust design are fitting the demands for every harsh environment applications such as logistics, transportation/ fleet management, heavy vehicles, utility and also outdoor usage. -
Page 9: Packing List
1.2 Packing List Carefully remove the box and unpack your device. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately. Standard factory shipment list: CD-ROM with User Guide User Manual Panel PC... -
Page 10: Appearance
1.3 Appearance Front, Side and Bottom View CAN-BUS 2 x RJ45 RS-232/422/485 Terminal block 9-36V 1 x USB 2.0 OSD Panel 1 x USB 3.0 HDMI Rear View... -
Page 11: Characteristics
1.4 Characteristics Part Number VMW12ID3S-M9-5RT Display Size in inches / resolution in pixels 12" / WXGA, 1280 x 800 400 nits / 400 cd/m² Brightness / luminance 600 nits / 600 cd/m² (optional) MTBF of backlight LED-backlight up to 50,000 hours in Eco mode Touchscreen Single-touch (resistive analog) System Hardware... -
Page 12: Dimensions
1.5 Dimensions... -
Page 13: Exploded Drawing
1.6 Exploded Drawing On the picture below you can see spare parts exploded drawing of a standard Rugged Display Computer... -
Page 14: Getting Started
2 Getting Started This chapter provides information on how to connect the device to the source of power, connector pinouts and the guideline to turn on/off the Panel PC. 2.1 Powering On 2.1.1 AC Adapter Components 2. Power Cord 1. AC Adapter 3. -
Page 15: Power Considerations
ALTERNATING CURRENT This product must be grounded. Use only a grounded AC outlet. Install the additional PE ground wire if the local installation regulations require it. *If you do not use a grounded outlet while using the device, you may notice an electrical tingling sensation when the palms of your hands touch the device. -
Page 16: Connecting The Power
2.1.3 Connecting the Power Connecting to the Power Source 1) Connect the 3-pin terminal block. 2) Screw the Terminal block to fix the cable. 3) Connect terminal block to the Panel PC. Once the device is connected to the source of power it is ready to work. 2.2 Turning On Your Device To turn on the Panel PC: 1. -
Page 17: Installing Operating System (Os)
2.3 Installing Operating System (OS) You may install your own OS if it is not installed. When installing OS to this Panel PC, please follow the steps and use external equipment such as Keyboard and Mouse. (a) Use external USB DVD-ROM to run the OS and Driver settings (as shown on the picture below) 2.4 Adjusting the LCD Display Brightness 1. -
Page 18: Connectors
2.5 Connectors 2.5.1 Wiring Requirements The following common safety precautions should be observed before installing any electronic device: • Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point. -
Page 19: Connector Pinouts
2.5.2 Connector Pinouts This Panel PC comes with various interfaces located on the bottom panel. The IO placement varies by processor and screen size of the Panel PC. The pin assignments of the cables are as follows: Terminal Block (9-36V) Minimum Voltage 9V Maximum Voltage 36V Maximum Current 6.6A... - Page 20 Ethernet (LAN) Connector Pin № Name Pin № Name TX1+ TX1- TX2+ TX2- TX3+ TX3- TX4+ TX4- Digital Input/ Output Connector (optional) Pin № Name Pin № Name Digital output: Open drain to 40V ; Maximum load 2.0A Digital input: Voltage Level 0: close to GND;...
-
Page 21: Turning Off Your Device (Windows 7)
2.6 Turning Off Your Device (Windows 7) To shut down your device, do the following: Tap Start ( ) > Shut down. Wait for your Panel PC to completely turn off before disconnecting the power cord (if necessary). NOTE: If your system is not Windows 7, the method to turn off the device may slightly vary. -
Page 22: Mounting Solutions (Optional)
3 Mounting Solutions (optional) This chapter provides mounting guide for all available mounting options. Pay attention to cautions and warning to avoid any damages. CAUTION/ ATTENTION Follow mounting instructions and use recommended mounting hardware to avoid the risk of injury. 3.1 Cable Mounting Considerations For a nice look and safe installation, make sure cables are neatly hidden behind the Panel PC. -
Page 23: Safety Precautions
3.2 Safety Precautions Observe the following common safety precautions before installing the equipment: • Use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must be crossed make sure the wires are perpendicular at the intersection point. •... - Page 24 Wall Mount *with customer’s bracket Mounting Steps: 1. Screw VESA Bracket to the fixture (ex. wall) with M4 flathead screws. 2. Place the device on VESA bracket. NOTE: Notice that both hooks on bracket should lock the notches on the back cover of the device.
- Page 25 Dash / Yoke Mounting (optional) Before setting up rugged bracket, please check whether all items present in the mounting kit. Rugged Panel PC bracket accessory list: One bracket stand; Three M5 x10 screws with washer; One locking handle adjustment tool with metal washer.
- Page 26 Mounting steps: 1. Place the Rugged Panel PC on the bracket stand, aiming screw hole for each other. 2. Secure three M5x10 screws to fix the device upon the bracket stand. 3. Secure tightly locking handle to the Panel PC.
- Page 27 4. Loosen the hand-screw adjustment tool, then you can adjust product angle on the stand. Then screw the product tightly again to secure the stand position.
-
Page 28: Maintenance
4 Maintenance This chapter includes regular cleaning and maintenance procedures. Follow all the recommendations in this chapter in order to ensure long product lifecycle. This equipment is extremely rugged and does not require a lot of maintenance. Remember that electrical equipment should be handled with care and used accordingly to its specifications. -
Page 29: Driver Installation
5 Driver Installation This chapter provides guideline to driver installations. The Panel PC comes with Motherboard User Manual and Driver CD according to the CPU, and contains most of the drivers and utilities that you need. To install Graphics, Chipset, VGA, Audio, SATA and Ethernet drivers, follow the step-by- step driver installation guide in the Motherboard User Manual (included in the package). -
Page 30: Configuration Utility
5.1.2 Configuration Utility After finishing the installation, follow the steps below to test the configuration utility. Step 1 Enter “My Computer”, click the “ELO Touch Screen” shortcut function. Step 2 Click “Align” function key to continue. - Page 31 Step 3 Calibrate four-point locations on the screen. Step 4 Click “Yes” if the cursor follows your finger and finish the utility test.
-
Page 32: The Premier Touch Driver Installation
5.2 The Premier Touch Driver Installation Touch-Kit is the Premier Touch software, which contains drivers of the touch panel controllers for the specified communication connectors, RS232, PS/2 and USB, and the other two utilities. The two utilities are as follows: ... -
Page 33: Configuration Utility
5.2.2 Configuration Utility After finishing the touch driver installation, you need to test the configuration utility. Step 1 Click the “Touch-Kit” shortcut function on the desktop. Step 2 Enter “General” functions and choose the language you need. Then Enter “Tool” function alignments to match the display. - Page 34 Step 3 Correct four-point locations on screen. Step 4 Press “Yes” to continue if four-point calibration test is complete successfully and press Ok to finish the screen calibration.
-
Page 35: Troubleshooting
6 Troubleshooting This chapter describes all known issues and solutions. 6.1 Display indistinct When using an “external display” as CRT or LCD for external mode (Panel & CRT), the resolution of external display may be recommended equal to the CMOS setting for panel [Flat Panel Type]. - Page 36 IMPORTANT: While using CF card as storage of the Operation System, you need to use “Fixed Disk Mode” type Compact Flash Card instead of removable disk mode. The internal Compact Flash socket is NOT A PLUG & PLAY DEVICE; you are allowed to remove the CF card only at POWER-OFF status.
-
Page 37: Pro-Face America Support
Pro-face America Support We offer multiple support programs for installation, configuration, and troubleshooting. For more information please contact Support Center at support@profaceamerica.com (800) 289-9266. New Product Satisfaction Return Pro-face offers standard warranties for up to two-years on all Pro-face brand products. There is no cost for parts and labor, while your products are under warranty.