Advertisement
Quick Links
Advertisement
Summary of Contents for DALRC QUHF
- Page 1 DALRC QUHF 433 MHZ Operating Manual...
- Page 2 GND=These 3 GND pins are all common ground. VCC=transmitter power supply input (support 2s-6s, 3s recommended) P/S=PPM or SBUS signal input (PPM and SBUS signal will be identified automatically) 5V=5Voutput (power supply receiver) 1=Channel 1 PWM input (if PPM2 was turn on then PPM2 input via this pin) 2=Channel 2 PMW input 3=Channel 3 PMW input...
- Page 3 TX/5=Channel 5 PMW input (when upgrading connect USB to TT L ’s RX) RX/6=Channel 6 PMW input (when upgrading connect USB to TT L ’s TX) 7==Channel 7 PMW input 8==Channel 8 PMW input Ground wire=These 10 GND pins are all common ground on receiver. 5V=Receiver 5V power supply input (support 3.3v-8v power suppl y, 5v recommended) Channel 1=Channel 1 PWM output...
- Page 4 Channel 6=Channel 6 PWM output Channel 7=Channel 7 PWM output Channel 8=Channel 8 PWM output Channel 9=RSSI output (Capable to set output mode) Channel 10=PPM output (Capable to set output mode) Above each pin’s function was defaulted by receiver, which is capa ble to reset to change its function, For example , set the channel 10 to SBUS output, details of setting process please refer the functi on diagram.
- Page 5 Transmitter restore to default setting: keep click the button 9 times and wait for instruction, once red light rapidly flashing pr ess button 1s more, release the button after the red light and blue l ight start flashing alternately , restore success. DALRC 433Mhz Transmitter Setup...
- Page 6 Continuously click the button on the Transmitter “N” times on standby mode condition system will enter into the corresponding f unction setting. For example: we want to set the transmitting power to (1500mW) • 1.5W, only need to click the function button 3 times, then flashes 3 times purple light (the purple light flashing times are same with the times you click the button) after that, coming to red light or blue light flashing (if the blue light intermittent flashed 4 times that mean the current power is...
-
Page 7: Blue Light
Continuously Indicator flash Corresponding click button Menu frequency and function Description frequency color Low power is 300mw, Transmitting Blue light 3 Low power available switch to power switch times 100-1500mw , (Continuously click button 3 times will User defined Red light 3 times switch) defaulted is 1000mw power... - Page 8 Double PPM1 corresponding Signal Red light 4 times input with transmitter ‘s input mode mode(channel 5 “P/S” input pin, and 6 acquired PPM2 corresponding selection from PPM2 transmitter’s channel signal, channel “1” input pin 1,2,3,4,7,8 acquired from PPM1signal) Double input mode(channel 3 and 4 acquired from...
- Page 9 channel Output 9-16 Red light 8 times mode(channel 1-8 channel signal input from (both In,channel 9-16 receivers’ lost input from control protection PPM1-PWm8 port) independent running, without interfere each other. ) greater the Transmitting Blue light 1 time 100mw power, the greater power 300mw Blue light 2 times...
- Page 10 Receiver’s channel set parameters to Blue light 4 times 1-10 output PWM receiver, once set success Receiver’s channel Blue light 5 times transmitter ‘s output 9-16 indicator light will channel ‘s PWM, stop flashing channel output (receiver RSSI, channel 10 outputted SBUS output PPM...
- Page 11 Keep in default Frequency Blue light 1 time Random mode for general hopping generated (default) case, the quantity frequency points set Frequency hopping points is many hopping points frequency hopping points Blue light 2 times Random divided from the generated frequency range 400Mhz-470Mhz...
- Page 12 Blue light 3 times 3KHZ Blue light 4 times 4KHZ Blue light 5 times 5KHZ (default) 6KHZ Blue light 6 times Blue light 7 times 7KHZ 8KHZ Red light 8 times Red light 9 times 9KHZ Red light 10 times 10KHZ Default relaying...
- Page 13 After restore Restore Factory Red light 1 time Factory Defaults Defaults transmitter all the settings will be reset to default restore Factory Default. Firmware upgrade connecting diagram: QUHF transmit, receive support online upgrade software, needing computer accessed into internet.
- Page 14 7 and channel 8. Software operation: While plug in QUHF device, after select the correct COM from COM Port ,QUHF device will connected automatically (check the COM Port from the device manager), then select the firmware from the choice box which is below the software and click start upgrade firmware ,after upgrading finished QUHF will restart, pull out the upgrade module.