1. Manuals
  2. Brands
  3. BCS Manuals
  4. IP Camera
  5. TIP5200IR
  6. Quick start manual

BCS TIP5200IR Quick Start Manual

F series indoor ip camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

HD IR Waterproof Fixed Network Camera Quick Start Guide
Version 1.0.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TIP5200IR and is the answer not in the manual?

Questions and answers

Summary of Contents for BCS TIP5200IR

  • Page 1 HD IR Waterproof Fixed Network Camera Quick Start Guide Version 1.0.0...
  • Page 2 Welcome Thank you for purchasing our network camera! This quick start guide is designed to be a reference tool for your system. Please keep this start guide well for future reference. Please open the accessory bag to check the items one by one in accordance with the list below. Contact your local retailer ASAP if something is missing or damaged in the bag.
  • Page 3 Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera. 6. Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work.

  • Page 4: Table Of Contents

    Table of Contents Structure ........................1 Multiple-function Combination Cable..............1 Framework and Dimension ................2 Bidirectional talk ....................3 1.3.1 Device-end to PC-end................. 3 1.3.2 PC-end to the Device-end ................3 Alarm Setup ...................... 4 Device Installation ......................6 Installation ......................6 Adjust Lens and Install SD Card ...............

  • Page 5: Structure

    1 Structure 1.1 Multiple-function Combination Cable Note: Figures in this chapter are for reference only, and different models use different figures, please select a or b model accordingly. You can refer to the following figure for cable information. See Figure 1-1 and Figure 1-2 Figure 1-1 Multiple-function combination cable a Please refer to the following sheet for detailed information.

  • Page 6: Framework And Dimension

    Please refer to the follow sheet for detailed pin information. Port Name Name Note Alarm output port. It is to output the alarm signal to the alarm device. ALARM_NO NO: normal open alarm output port. This port shall be used with ALARM_COM port. ALARM_COM Alarm output public port.

  • Page 7: Bidirectional Talk

    Please refer to the following two figures for dimension information. The unit is mm. See Figure 1-3 and Figure 1-4. Figure 1-3 Dimension illustration 1 Figure 1-4 Dimension illustration 2 1.3 Bidirectional talk 1.3.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC.

  • Page 8: Alarm Setup

    Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the audio talk function. Click Talk button again to stop the bidirectional talk function. Please note the on-site listening operation is null during the bidirectional talk process. Listening Operation At the PC-end, speak via the speaker or MIC, and then you can get the audio from the earphone or sound box at the device-end.
  • Page 9 Figure 1-6 Alarm input Please refer to the following figure for alarm output information. See Figure 1-7. Port NO and Port C composes an on-off button to provide the alarm output. If the type is NO, this button is normal open. The button becomes on when there is an alarm output.

  • Page 10: Device Installation

    2 Device Installation 2.1 Installation Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference. Step 1. On installation surface, mark hole for bracket installation and insert three expansion bolts on installation surface. Push the three expansion bolts into the installation holes and fasten them.

  • Page 11: Bracket Adjustment

    Figure 2-2 Lens 2.3 Bracket Adjustment You can adjust bracket via a M4 inner hex wrench. Before adjustment, you shall loosen screw via inner hex wrench in accessories bag, and rotate rear cover 360° horizontally, rotate 90° vertically. Rotate pedestal 360° . Fasten screw via inner hex wrench.
  • Page 12 Figure 2-3 Bracket...

  • Page 13: Quick Configuration Tool

    3 Quick Configuration Tool 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”...
  • Page 14 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 3-1), please select a device IP address and then double click it to open the login interface.

  • Page 15: Web Operation

    4 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. ...
  • Page 16 Figure 4- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 4- 3. Figure 4- 3 Web monitoring window...

  • Page 17: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Cr VI PBDE ○ ○ ○ ○ ○ ○ Circuit Board Component ○ ○ ○ ○ ○ ○ Device Construction Material ○ ○ ○ ○ ○...

Table of Contents