Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for MicroDome AV4655DN-08
-
Page 1: Models
MicroDome® Installation Manual Models: 4 Megapixel AV4655DN-08 AV4655DN-28 AV4655DN-NL 4 Megapixel WDR AV4656 DN-08 AV4656DN -28 AV4656DN-NL 6 Megapixel AV6655DN-08 AV6655DN-28 AV6655DN-NL 6 Megapixel WDR AV6656DN-08 AV6656DN-28 AV6656DN-NL 10 Megapixel AV10655DN-08 AV10655DN-28 AV10655DN-NL... -
Page 2: Table Of Contents
Microdome Duo® Installation Manual Contents Models ..............................1 Package Content ........................... 3 Warranty Information ..........................4 Camera Overview ..........................5 Surface Installation ..........................6 Drop Ceiling Mount Adapter Plate Installation ..................8 MDD-CAP Installation ..........................9 MDD-CMT/WMT Pendant Mount and Wall Mount Installation...............10 MDD-FMA Flush Mount Installation ......................11... -
Page 3: Package Content
Microdome Duo® Installation Manual CAUTION! 1. Do not attempt to service a damaged unit yourself. Refer all servicing to qualified service personnel. 2. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. -
Page 4: Warranty Information
Microdome Duo® Installation Manual Warranty Information Global (3 Year) Limited Warranty ARECONT VISION warrants to Purchaser (and only Purchaser) (the “Limited Warranty”), that: (a) each Product shall be free from material defects in material and workmanship for a period of thirty-six (36) months from the date of shipment (the “Warranty Period”);... -
Page 5: Camera Overview
Binning Mode increases the camera’s low light performance by combining pixels so that more light can be collected. MicroDome Duo cameras are designed for demanding environments. They are rated IP 66 for dust and water ingress protection and rated IK-10 for vandal resistance. -
Page 6: Surface Installation
Microdome Duo® Installation Manual Surface Installation 1. Determine a secure location to mount the camera. 2. Use the supplied security L-key, to loosen the four (4) screws which secure the cover. PIC. 1 3. Remove the cover. Do not remove screws from the dome cover. - Page 7 Microdome Duo® Installation Manual PIC. 3 PIC 4 8. Re-attach camera to adapter plate (Reverse step 4 and 5) 9. Re-attach cover to camera (Reverse step 2 and 3) Page | 7 support@arecontvision.com +1.818.937.0700 877.CAMERA.8 www.arecontvision.com avsales@arecontvision.com...
-
Page 8: Drop Ceiling Mount Adapter Plate Installation
Microdome Duo® Installation Manual Drop Ceiling Mount Adapter Plate Installation Repeat step 1-5 of Surface Installation (See Pic. 1-3) 6. Use template and cable location to create mounting provisions for the Plate. Use 3/16” drill bits for four mounting holes in Drop Ceiling Panel. -
Page 9: Mdd-Cap Installation
Microdome Duo® Installation Manual MDD-CAP Installation Repeat step 1-5 of Surface Installation (See Pic. 1-3) 6. Insert Adapter Plate into the Cap and attach it to the cap, using the 4 screws through 4 “A” holes using enclosed #6-32 screws. -
Page 10: Mdd-Cmt/Wmt Pendant Mount And Wall Mount Installation
Microdome Duo® Installation Manual MDD-CMT/WMT Pendant Mount and Wall Mount Installation Assembly (Pic. 7) can be used with wall mount or ceiling mount PIC 8 PIC. 9 Use MCD-CMT and MCD-WMT installation instructions for reference. Page | 10 support@arecontvision.com +1.818.937.0700 877.CAMERA.8... -
Page 11: Mdd-Fma Flush Mount Installation
Microdome Duo® Installation Manual MDD-FMA Flush Mount Installation Note: MDD-FMA is designed for indoor use only. Grommet use is recommended. 1. Use template to cut the ceiling plate and create mounting provisions for the Flush Mount Ceiling Panel. PIC. 10 2. - Page 12 Microdome Duo® Installation Manual 4. Plug PoE cable (not shown for clarity) 5. Hold all four latches as shown on PIC. 12 PIC. 12 6. Insert camera into cutout prepared in step 1 PIC. 13 Page | 12 support@arecontvision.com +1.818.937.0700 877.CAMERA.8...
- Page 13 Microdome Duo® Installation Manual PIC. 14 7. Undo 4 screws shown and remove both Rings and Bubbles. PIC. 15 Bubbles Rings 8. Adjust Pan and Tilt for both modules as shown on page 14. 9. Re-attach Rings and Bubbles and tighten 4 screws from step 7.
-
Page 14: Pan And Tilt Adjustment
Microdome Duo® Installation Manual Pan and Tilt Adjustment 1. Use the supplied security L-key, to loosen the four (4) screws which secure the cover. See Pic. 1. 2. Remove the cover. 3. Adjust the pan and tilt of each camera module to obtain the desired field of view. -
Page 15: Lens Replacement
Microdome Duo® Installation Manual Lens Replacement 1. Use the supplied security L-key, to loosen the four (4) screws which secure the cover. (See Pic. 1). Remove the cover. PIC. 18 2. Manually turn the lens counter clockwise, this may take several turns. -
Page 16: Usage Of Ethernet Cable Other Than Included M/F Poe Cable
Microdome Duo® Installation Manual Usage of Ethernet cable other than included M/F PoE cable. 1. Insert CAT 5E cable into Grommet Installation Tool as shown on Pic. 19. 2. If intend to use AC/DC power to power up the camera, insert the wire (not supplied) into grommet. See instructions on page 23 for cable preparation. -
Page 17: Connecting Digital I/O
Microdome Duo® Installation Manual Connecting Digital I/O 1. To use digital I/O use 5-wire pigtail cable (included) and plug it into I/O connector (Pic 13). The color coding is shown in Table 1 below PIC. 20 5-Pin I/O Connector PoE Connector AC/DC Connector... -
Page 18: Aux I/O Use Case Example
Microdome Duo® Installation Manual AUX I/O use case example Arecont Vision AUX I/O ALARM OUT+ 120V ALARM-OUT 100mA (max) ALARM OUT- 3.3VO ALARM Normally Open/Close 250Ω ALARM ALARM-IN 0-12VDC 50mA (max) Page | 18 support@arecontvision.com +1.818.937.0700 877.CAMERA.8 www.arecontvision.com avsales@arecontvision.com... -
Page 19: Output Relay Control And Function
Microdome Duo® Installation Manual OUTPUT Relay Control and Function The camera has an output for activating an external device. The camera supports both transient and continuous relay operation. You can operate the relay during an active connection using the API command set. -
Page 20: Input Alarm Control And Detection
Microdome Duo® Installation Manual INPUT Alarm Control and Detection The input optocoupler supports two ways to connect external unsupervised alarms to Arecont Vision camera. Only one of the following two schemes should be used at any given time. OPTION-1: UNSUPERVISED ALARM D ETECTION In this scheme the IN+ &... - Page 21 Microdome Duo® Installation Manual In this scheme the IN- & GND terminals can be tied to an external power source. The camera can detect a range of voltage to trigger an internal alarm on|off condition. 0-12VDC 50mA (max) The following table shows the input voltage range and electrical characteristics:...
-
Page 22: Camera Power Up Using Poe
Microdome Duo® Installation Manual Camera Power Up using PoE This product should be installed by a qualified service technician in accordance with the National Electrical Code (NEC 800 CEC Section 60) or applicable local code. Make sure that your installation of wires complies with Electrical Code of the local government where the camera is installed and no bare wires are exposed. -
Page 23: Use Of Auxiliary Power
Microdome Duo® Installation Manual Use of Auxiliary Power 1. If the camera is powered by a separate outside AC or DC power source, run the wire (not supplied) through the grommet and connect the power cable to the 4-position connector on the Main Board. (see Page 17 and 18 for illustration and detailed instructions) 2. -
Page 24: Camera Discovery, Setup, And Configuration
Microdome Duo® Installation Manual Camera Discovery, Setup, and Configuration For camera discovery and setup, the AV IP Utility is recommended. The software can be found on the CD included with your camera or at: http://www.arecontvision.com/softwares.php. The AV IP Utility has the ability to provide multiple discovery options, including broadcast and multicast, check the status of a camera, change camera settings, import and export camera settings via a .csv file, and update firmware and/or hardware from virtually anywhere with a... -
Page 25: Network Protocols
Microdome Duo® Installation Manual Network Protocols The Arecont Vision MicroDome Duo cameras support RTSP, RTP/TCP, RTP/UDP, HTTP, DHCP, TFTP, QoS, IP version 4 (IPv4) and IP version 6 (IPv6). RTSP Cameras communicate with video management systems over Real Time Streaming Protocol. -
Page 26: General Remote Focus
Microdome Duo® Installation Manual General Remote Focus 1. To control the remote focus via the web interface, double click the camera within the AV IP Utility (Figure 1) or open your preferred web browser and type the camera’s IP address (Figure 2). - Page 27 Microdome Duo® Installation Manual 5. Please complete the same action for Channel 2 by following steps 2 to 5. Page | 27 support@arecontvision.com +1.818.937.0700 877.CAMERA.8 www.arecontvision.com avsales@arecontvision.com...
-
Page 28: Av Ip Utility Focus Tab
Microdome Duo® Installation Manual AV IP Utility Focus Tab Menu Feature Description Manual Numbers indicate the level of focusing in order to adjust the field-of-view. Focus: +20, +5, +1, -20, To set-up a focus area (if necessary), draw a rectangle with the mouse -5, -1 (by left-clicking and dragging the mouse to a desired zoom size). -
Page 29: Administration And Password Setting
Microdome Duo® Installation Manual Administration and Password Setting Administration is the place to set a password. Arecont Vision cameras support two levels of password- protected access control. Camera authentication is compatible with RFC-2068 HTTP 1.1 and is supported by all standard browsers and video surveillance software. -
Page 30: Reset To Factory Default
Microdome Duo® Installation Manual Reset to Factory Default Press and hold the Reset Button, release it after 10 seconds. See picture below for approximate switch position on board. The camera has been reset to the factory default. If the camera is not connected to DHCP server, the camera will use Link-local address. -
Page 31: Troubleshooting
Microdome Duo® Installation Manual Troubleshooting Before troubleshooting, visit http://www.arecontvision.com/ to ensure your camera has the most current firmware version. Page | 31 support@arecontvision.com +1.818.937.0700 877.CAMERA.8 www.arecontvision.com avsales@arecontvision.com... -
Page 32: Support
Microdome Duo® Installation Manual Support 1. Arecont Vision FAQ Page Located at ArecontVision.com 2. Check the following before you call: Restore camera to factory default with AV200 or the camera webpage. Upgrade to the latest firmware by visiting ArecontVision.com.
Need help?
Do you have a question about the AV4655DN-08 and is the answer not in the manual?
Questions and answers