Advertisement
Quick Links
Rev. 2, 10-15-2012
Fancy Foam Models
www.fancyfoam.com
Assembly Instructions for the following EPP models:
32" Yak-55
32" Yak-54
32" Edge 540
32" Sbach 342
33" Fenix V2
34" Freestyle
34.5" MX2
Recommended Electronics and motors:
Motor: Turnigy 2730-1500 or any equivalent motor
Speed control: Castle Creations Thunderbird 9 or
equal.
Battery: 300 to 500, 2 or 3 cell, 20C rated or
equivalent.
Receiver: 4 channel.
Servos: (2) HXT 500 for the tail and (1) HXT 900 for
the ailerons.
Disclaimer: Fancy Foam Models has done
everything we can to caution and inform the end
user regarding the use of Lithium polymer battery
technology. We are in no way responsible for any
damage that may be caused by these batteries.
Please read, understand and follow all instructions
for the charger and batteries. Failure to use this
battery technology properly can result in the risk of
fire. If you are not comfortable with this
technology, return the batteries packs and kit to us
for a refund. By building the kit and using the
batteries, you accept full responsibility for the
safety of these batteries.
Recommended building methods and glues:
Much of the construction of this model is done by
laying the parts on a flat table. It is strongly
recommended that you put wax paper down on the
surface first so any excess glue doesn't soak through
the foam and glue the parts to the table. For all
assembly, use "Welders" contact adhesive. The hinges
are also done with Welders, see our video on the web
site. Hot glue can be used to attach the servos and
control horns.
Starting out:
Look over the parts and dry fit them together to check
for proper fit.
Painting:
It is easiest to paint the parts before assembly. Card
stock can be used to make templates for stripes,
checkers, ect... Epp does is not affected much by
solvents so Krylon, Testors and airbrush paints can be
used.
Horizontal parts assembly:
Glue the spar tube into the slot in the bottom of the
wing.
Cut a 6" long piece of 1.5mm carbon pushrod. Cut a v-
slot in the bottom of the elevator just behind the hinge
bevel and glue in the 6" carbon piece.
1
Advertisement
Related Manuals for Fancy Foam Models 32” Yak-55
Summary of Contents for Fancy Foam Models 32” Yak-55
- Page 1 Servos: (2) HXT 500 for the tail and (1) HXT 900 for the ailerons. Disclaimer: Fancy Foam Models has done Cut a 6” long piece of 1.5mm carbon pushrod. Cut a v- everything we can to caution and inform the end...
- Page 2 Hinge the ailerons to the wing and the elevator to the horizontal stabilizer. (A Welders glue hinge instructional video is on the web site.) Glue the lower vertical fuselage pieces to the horizontal assembly making sure it is square. Glue together the horizontal pieces; nose, wing, rear fuselage and horizontal tail.
- Page 3 Landing Gear (optional): Install the motor onto the motor mount and velcro the speed control and receiver to the lower left side of the Cut 2 pieces of the 1.5mm carbon, 8” long and two fuselage. pieces 1” long. Glue them together as shown with a Use an exacto knife to slot the control horn locations in 1/8”...
- Page 4 Fenix V2 is 3” behind the leading edge of the wing. We hope you enjoy your airplane. Thank You, Mike & Niki Bailey Fancy Foam Models Flight set-up: Use double stick Velcro on the battery and airframe to secure the battery to the bottom of the horizontal fuselage in a location that gives the model proper balance.