Technics RS-TR575 Operating Instructions Manual page 13

· · · · · ·· · · ·· · ·· · · · · · · · · · · · · · ·· · · · · · · · · · · ·· · · · · · · · · ·
REClEVEL
Use the REC LEVEL control
About the selection of the Dolby NR type
5
to adjust the recording level.
rIJ
The Dolby NR effect can be obtained by using the same type of
• (Refer to the right of this page.)
o
10
Dolby NR during both record ing and playback. Refer to the follow­
O
Ing table when selecting the type (either B or C).
!10j·
tb\\~ · ~ ~~.~ ·t~ · · ~~.~~. ; .
. . . . ....
p ~~~~. b~gi~
.;>::.
ding, and play the source to
.<....:
be recorded.
~ :
Forward side
~ :
Reverse side
1111,-,"1:: 11'-'
U
U.U:J..
U U
ClDI
L
P y ................ -.
1110 ...
~ R
illuminates
I11J1!J
When recording on both sides of the
tape, be sure to press the
~
button.
To record on Deck 2, In steps I, 4, 5 and 10 above, press the but·
tons
J ,
4J , {}
and
J
r[}
for Deck 2.
To temporarily stop recording
PAUSE
Press
II
PAUSE.
~
P,." '"'" ...,"
to ,""me
"",,,dlo,.
To stop recording
~
Pross ••
Use this type when the deck on which the tape
Type B
will be played back is equipped with only type B
Dolby NR.
Use this type when the deck on which the tape
will be played back is equipped with type C
Type C
Dolby NR. (for example, when this unit is also go·
ing to be used to play back the tape.)
(Refer to "About the Dolby noise-reduction system " on page 8.)
About the recording level adjustment
If
the recording level is too high, there will be distortion In the
recorded sounds, and if
it
is too low, the hiss noise Inherent to
recording tapes will become noticeable.
In order to make high·quality recordings, use the REC LEVEL con·
trol to adjust so that highest values of the input level Indicated by
the level meter do not exceed the standard record ing level (the
number indicated in parentheses) for the tape being used.
11'-' 11 ,-, ::
11 ,-, ,-,,-,
UU.UU • UU.UU
L IIIIIIIIIII.UIIIIIII .. IIIIIIIIII _
• -to __ -til -I -J aDO +t +4 1'\..&,
.. A 'UII .. II .. IIIIIIIIIIIIIIIIIIIIII" ..
Normal or Cr02 tape (O).J
L
Metal tape (
+
2)
To cancel the ATC settings
[While ATC settings are In progress]
~
Pross ••
[After ATC settings have been completed]
~
ProssATC.
If Ihe
00
Indicator begins to flash quickly while the ATC 8et·
lings ere In progreu,
it indicates that the settings cannot be
made for one of the foilowlng reasons.
• The tape has reached the leader tape.
• The tape is severely damaged.
• The cassette deck's heads are severely dirty.
• The tape Is a non·standard type, such as a metal tape which
has no tape type identification hole in the cassette.
IlB11J
• If
the cassette holder is opened after the ATC settings have
been completed, the settings will be canceled.
• When making the ATC settings midway along a tape, provide a
silent interval at least 2 seconds long after the last track prior to
where the settings will begin.
13