Table of Contents
Advertisement
Quick Links
WARRANTY INFORMATION
This warranty is provided by Total Tools (Importing) Pty Ltd of 19 Grimes Court, Derrimut, VIC 3030.
Phone: 03 9394 4300 (we, us, our).
Express warranty
Subject to the exclusions set out below, we warrant that this product will be free from defects in materials or
workmanship for a period of 12 months from the date of purchase.
The benefits conferred by this warranty are in addition to all rights and remedies which you may be entitled to under
the Australian Consumer Law, and any other statutory rights you may have under other applicable laws.
This warranty does not exclude, restrict or modify any such rights or remedies.
Warranty exclusions
This express warranty does not apply where a defect or other issue with the product is caused by normal wear and
tear, misuse or abuse of the product.
Consumer guarantees
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Warranty claims
To make a claim under this warranty, you must bring the product along with the proof of purchase and any other
documentary evidence which you think is relevant to the Total Tools' place of purchase where the claim will be
handled on our behalf. Any cost incurred by you in bringing the product to the place of purchase will be borne by you.
To make a claim under this warranty, the product and proof of purchase must be returned to the Total Tools place of
purchase during the warranty period specified above.
If your warranty claim is accepted, we (or the Total Tools store that handles the claim on our behalf) will, at our
discretion, repair or replace the product, or refund money to you and take back the product.
PEDESTAL FAN & WALL FAN
OPERATING INSTRUCTIONS
Model No: DFS75 .. 80788
Model No: DFB75 .. 80789
Model no.
DFS75
TO PREVENT SERIOUS INJURY, READ
AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Model no.
DFB75
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for DETROIT DFS75
-
Page 1: Operating Instructions
PEDESTAL FAN & WALL FAN OPERATING INSTRUCTIONS WARRANTY INFORMATION Model No: DFS75 .. 80788 This warranty is provided by Total Tools (Importing) Pty Ltd of 19 Grimes Court, Derrimut, VIC 3030. Model No: DFB75 .. 80789 Phone: 03 9394 4300 (we, us, our). -
Page 2: Safety Instructions
SAFETY INSTRUCTIONS This product is intended for indoor use only. Always operate the product from a power source of the same voltage, frequency and rating as indicated on the product identification plate. To reduce the risk of electric shock, do not use this fan with any solid state speed control device. -
Page 3: Fan Dimensions
FS.FB-65-020-020-000 Front net Spray coating FS.FB-65-020-010-000 Back net Spray coating Model FS.FB-65-070-020-000 Rating label Label FB-65-061-000-000 Hanger wall combination Spray coating DFS75 1500 1900 1250 GB30-76 Hex bolt M8X25 Plate color zinc GB30-76 Hex bolt M8X20 Plate color zinc ∮6/NYLON1010 DFB75 12.5... - Page 4 EXPLOSION VIEW & PARTS BREAKDOWN PEDESTAL FAN ASSEMBLY FRONT GUARD REAR GUARD OSCILLIATING 18, 17, 16. ADJUSTMENT MOTOR SCREW SET SCREW SHAFT FEMALE SUPPORTER MALE SUPPORTER SET SCREW BLADE 9, 10, 11, 12. INNER TUBE Fit REAR GUARD of fan onto the MOTOR and secure with 4 screws provided.
-
Page 5: Specifications
Attach the wall mount base to the wall by drilling two holes with a M10*80 (mm) (V~) (Hz) /min) drill bit. Secure with the two M12 screws provided. DFS75 Pedestal Fan 220-240 NOTE: Installation height should be a minimum of 2.5 metres from the ground. DFB75 Wall Fan 220-240 IMPORTANT: Check wall is suitable for mounting and supporting the wall fan. -
Page 6: Environment Of Use
WALL FAN ASSEMBLY CONTINUED SWING ARM Insert the motor into the female support and secure with the screw. FAN HEAD FEMALE SUPPORTER LOCATING SCREW FIG 1 – The fan switch on the OFF position FIG 2 – The fan head in the FIXED air flow position Secure locking screw on FEMALE SUPPORTER for desired head angle / tilt.
Need help?
Do you have a question about the DFS75 and is the answer not in the manual?
Questions and answers
Hi, we have assembled the DFS75 pedestal **** and have a small bolt and nut in a plastic packed left. Can't see where it belongs in the instructions or on the ****. Any ideas? Thanks
The provided context does not specify the placement of an extra bolt and nut in the DETROIT DFS75 pedestal assembly.
This answer is automatically generated