Related Manuals for Leeds PTZPRO 12
Summary of Contents for Leeds PTZPRO 12
-
Page 1: User Manual
700TVL Mini Speed Dome Camera User Manual INSTRUCTION MANUAL Please read this manusl thoroughly before use and keep it handy for future reference... -
Page 2: Warnings And Cautions
WARNINGS and CAUTIONS WARNINGS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY MEALMETALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHERS OPENINGS ON THE EQUIPMENT. CAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). -
Page 3: Table Of Contents
IMPORTANT SAFEGUARDS/ TABLE of CONTENTS IMPORTANT SAFEGUARDS • Read all of the safety and operating instructions before using the product. • Keep the temperature from -50˚C to 50˚C (Outdoor) • IP67 (Waterproof) (Outdoor) • That avoid flammability material or oil. •... -
Page 4: Pacage Contents
PACKAGE CONTENTS The following parts are supplied with the mini speed dome system. 1. Dome camera 2. User’s manual 3. M3 x 15mm self tapping screws for surface mount installation M3 x 8mm self tapping screws for surface mount installation 4. -
Page 5: Before Installation
INSTALLATION & CONFIGURATION Switch Settings Before installation, please set the switches as described in this manual. *Address setting from 1 to 99 using rotary swith. (For example) If you want address setting for No. 8 Please make a both rotary switch by left No. 0 and right No. 8 In case of over 99 address, you can use virtual address <... -
Page 6: Surface Mount Installation
INSTALLATION & CONFIGURATION Surface Mount Installation 1. Punch out the pie-shaped section from the supplied templates (See Figure 4). Using the pie-shaped template, either cut a hole through the ceiling or make a hole with a depth of 0.25 inches (6mm). <Figure 4>... -
Page 7: Interface Cable Wiring
INSTALLATION & CONFIGURATION 4. Line up the tabs on the trim ring with the slots in the dome drive. Snap the trim ring and bubble into place. Refer to Figure 8 & Figure 11. <Figure 8> Snap the bubble and trim ring into place <Table D>... -
Page 8: In Ceiling Installation
INSTALLATION & CONFIGURATION IN CEILING INSTALLATION 1. Using the supplied template, cut holes in the ceiling for the dome drive and mounting hardware. Pull the wiring for power, video, and control through the ceiling. 2. Remove the surface mount ring from the dome drive as follows. Refer to Figure 2. a. - Page 9 PACKAGE CONTENTS The following parts are supplied with the mini speed dome system. 1. Dome camera Unit 2. Mount Housing(W/O Sunshield) or Mount Housing(With Sunshield) 3. Set Anchor(4 SET) 4. Wrench-2mm 5. Wrench-4mm 6. User’s manual Dome camera unit Mount Housing Mount Housing (W/O Senshield) (With Sunshield)
-
Page 10: Baud Rate
INSTALLATION & CONFIGURATION Switch Settings Before installation, please set the switches as described in this manual. *Address setting from 1 to 99 using rotary swith. (For example) If you want address setting for No. 8 Please make a both rotary switch by left No. 0 and right No. 8 In case of over 99 address, you can use virtual address <... - Page 11 INSTALLATION & CONFIGURATION Wall Mount Installation (INDOOR / OUTDOOR) 1. Feed the cables from the pass-through hole WRENCH 2mm(SUPPLIED) in the mounting surface through the pipe as shown in Figure 4. 2. Securely mount the pipe to the mounting bracket. ①...
-
Page 12: Wall Mount Installtion
INSTALLATION & CONFIGURATION 9. Wall Mount Installation 8. Secure with three stainless steel fasteners (attached to the trim ring) using the supplied hex wrench as shown in Figure 8. ⑧ <Figure 9.1> <Figure 9.2> Wall Mount WRENCH 4mm(SUPPLIED) Wall Mount Installation with Installation without Sun Shield... -
Page 13: Ceiling Mount Installtion
INSTALLATION & CONFIGURATION 5. Connect the cable as shown in Figure 12. 7. Plug the male RJ45 connector and ALARM connector 6. Securely mount the top housing to the ceiling pipe. into the mating connector on the top of the dome drive as shown in Figure 13. -
Page 14: Interface Cable Wiring
INSTALLATION & CONFIGURATION <Table D> Interface Cable Wiring Name Wire Color Name Wire Color Alarm 1 Green Brown Alarm 2 Bule Alarm 3 Violet Orange Alarm 4 White/Brown TRX- Yellow Brown TRX+ Black Power CONT. COLOR PMC14H BRIGHT TINT UNDER VOLUME S-VIDEO SCAN... -
Page 15: Specification
SPECIFICATION Outdoor Indoor Image Sensor 1/4" Sony Super HAD II(Double Scan) CCD Lens x12 Day & Night Zoom Lens Focal Length f =3.8mm~45.6mm Minimum Focus Distance F1.6(wide)~F2.7(tele) S/N Ratio more tha 50dB (AGC o ) Day & Night Day / Night / Auto / Ext Camera Resolution Max 700TV lines in color @HR 7mode(750TVL lines in B/W @ 7mode) -
Page 16: Operation & Programming
OPERATION & PROGRAMMING GENTTING STARTED This manual designed to be a reference tool for the installaton, programming and operation of your system. You need to install system before using this manual. Refer to <installation> part of this manual. Once installed, apply power to the dome. The system will start a con guration sequence. This information will remain on the monitor until dome operation begins. - Page 17 OPERATION & PROGRAMMING The 1st screen The 2nd screen ROOT MENU Value INFO SYSTEM :0-00-00-000-00000 MODEL :XXX-XXXX VERSION :XXX-XXXX VIDEO :NTSC or PAL PROTOCOL :STANDARD COMM. : RS485/02400 ADDRESS : XXX TEMP. : XXX.XC/XXX.XF REBOOT Reboot : <ENT> <OPEN> Exit : <CLR>...
- Page 18 OPERATION & PROGRAMMING ROOT MENU The 1st screen The 2nd screen Value PROP. PAN/TILT MOTION : ON/OFF AUTO FLIP : ON/OFF OVER TILT : ON/OFF AZIMUTH ZERO : OFF/0~360 LIMIT STOP : ON/OFF -LEFT LIMIT (Default OFF: NULL) ON : 0~360 -RIGHT LIMIT (Default OFF: NULL) ON : 0~360...
-
Page 19: System Information
OPERATION & PROGRAMMING SYSTEM : INFO The system Information displays serial number/model name/ Running /version/ <<<<< Main MENU >>>>> Protocol/Communication Type/Address switch No./Temperature. ██████████████████████████ ►SYSTEM > DISPLAY > System settings cannot be edited in this menu. This screen is for reference only. DOME >... -
Page 20: Event Log
OPERATION & PROGRAMMING SYSTEM : FACTORY Use this function to reset all camera settings to factory default parameters. You can reset a speci c setting to factory default parameters. <<<<< Main MENU >>>>> ██████████████████████████ ►SYSTEM > Use the following steps to display the System Information screen: DISPLAY >... -
Page 21: Password
OPERATION & PROGRAMMING SYSTEM : PASSWORD The dome features password protection to prevent unauthorized changes to the <<<<< Main Menu >>>>> dome settings. An operator cannot access any of the Dome Settings menus. ██████████████████████████ ►SYSTEM > Controller/ keyboard commands cannot override password-protected settings. DISPLAY >... -
Page 22: Display : Osd Setup
OPERATION & PROGRAMMING DISPLAY : OSD SETUP OSD setup allows you to program how labels are displayed on the monitor. <<<<< Main MENU >>>>> ██████████████████████████ SYSTEM > The following labels are available : ►DISPLAY > TITLE Identi es area and operation titles. DOME >... -
Page 23: Area Title
OPERATION & PROGRAMMING DISPLAY : AREA TITLES <<<<< Main MENU >>>>> ██████████████████████████ SYSTEM > ►DISPLAY > OSD SETUP A zone is a pan area, de ned by a left and right limit on the pan plane. > ►AREA TITLES DOME The dome system is capable of 8 area titles, each with a 12 character label. -
Page 24: Image Setup
OPERATION & PROGRAMMING DISPLAY : IMAGE SETUP This menu allows operator to change of displayed image settings. <<<<< Main Menu >>>>> ██████████████████████████ To set up image display SYSTEM > ►DISPLAY > OSD SETUP 1. Press the MENU key (refer to ‘Accessing main menu’) DOME >... -
Page 25: Dome : General Setup
OPERATION & PROGRAMMING DOME : GENERAL SETUP This menu controls general dome related functions. <<<<< Main Menu >>>>> Detail description is as follow. ██████████████████████████ SYSTEM > DISPLAY > ►GENERAL VIRTUAL ADDRESS ►DOME > MOTION Dome ID is generally assigned with address switch. CAMERA >... -
Page 26: Motion
OPERATION & PROGRAMMING DOME : MOTION PROPORTIONAL PAN/TILT <<<<< Main Menu >>>>> Proportional pan/tilt automatically reduces or increases the pan ██████████████████████████ and tilt speeds in proportion to the amount of zoom. SYSTEM > DISPLAY > GENERAL At telephoto zoom settings, the pan and tilt speeds will be ►DOME >... -
Page 27: Home
OPERATION & PROGRAMMING DOME : HOME This feature de nes the activity which is set should be executed <<<<< Main Menu >>>>> after assigned idle time. ██████████████████████████ SYSTEM > ACTION / NUMBER DISPLAY > GENERAL ►DOME > MOTION CAMERA > ►HOME PRESET [NUMBER] Dome goes to preset [NUMBER]. - Page 28 OPERATION & PROGRAMMING DOME : TOUR The dome system has 8 guard tours. Each of the tour has 30 items. Each item can have pre-de ned preset, pattern, scan and any other tour. <<<<< Main Menu >>>>> ██████████████████████████ SYSTEM > To program a tour.
-
Page 29: Camera : Focus / Zoom
OPERATION & PROGRAMMING DOME : SCAN Scan is a pan and tilt functions from one point to another point. The dome has 8 user-de ned auto scans. <<<<< Main Menu >>>>> ██████████████████████████ SYSTEM > To program a scan : DISPLAY > GENERAL ►DOME 1. -
Page 30: White Balance
OPERATION & PROGRAMMING CAMERA : WHITE BLANCE This feature automatically processes the viewed image to retain color balance over temperature range. The default setting for auto white balance is ATW. <<<<< Main Menu >>>>> ██████████████████████████ SYSTEM > White Balance has following four modes. DISPLAY >... -
Page 31: Exposure
OPERATION & PROGRAMMING CAMERA : EXPOSURE MODE : AUTO, MANUAL, SHUTTER PRI, IRIS PRI <<<<< Main Menu >>>>> ██████████████████████████ IRIS SYSTEM > AUTO Function that automatically opens and closes the iris in response to DISPLAY > DOME > FOCUS/ZOOM changing light conditions. ►CAMERA >... -
Page 32: Alarm
OPERATION & PROGRAMMING CAMERA : MOTION DETEC It instructs the camera to detect movement within the monitoring area and <<<<< Main Menu >>>>> the send an alarm signal automatically. ██████████████████████████ SYSTEM > DISPLAY > - You can set up to 3 MD Window. DOME >...
Need help?
Do you have a question about the PTZPRO 12 and is the answer not in the manual?
Questions and answers