A&A Global Industries Triple Crown Assembly Manual

Bulk vending machine

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

ASSEMBLY MANUAL

Table of Contents

Summary of Contents for A&A Global Industries Triple Crown

Page 1 ASSEMBLY MANUAL...
Page 2: Table Of Contents
INDEX Candy, changing ....15 Case, mounting ....10 Delivery system .
Page 3: Machine Specifications
PRODUCT CAPACITY Pan Candy: Approx. 9 lbs./sleeve, 27 lbs. total Superballs: Approx. 300/sleeve, 900 total Rocket Ball Gum: Approx. 180/sleeve, 540 total 1" Capsule: Approx. 265/ sleeve, 795 total NOTE: Be sure to check all parts before starting! Triple Crown Assembly...
Page 4 (Figure 1) Triple Crown Assembly...
Page 5: Parts, Listing
TC 313-01 Chute Cover C6-111-44N Chute Door (Thank You) TC 303-03 Chute TC 5059 Cash Box TC 321-03-B Black TC 321-03-P Pearl TC 321-03-G Green TC 330-00 Delivery Platform VH99-0200 Victor Kep Nut TC 330-02 Trap Door Triple Crown Assembly...
Page 6: Tools Needed
Capsule Wheel C6-411 Rocket Wheel TC6-441H Rocket Housing C6-411-22J Jawbreaker Wheel C6-412-7 Riser 658 PP (9) Screws [3 per Wheel and Brush-Off] TOOLS NEEDED " Open/Closed End Wrenches " Open End Wrenches or Crescent Wrenches (1) Phillips Screwdriver Triple Crown Assembly...
Page 7: Stand, Octagon
If properly installed and tightened, both keps nuts on the ends of the center rod should be flush with the edge of the rod. Triple Crown Assembly...
Page 8 If corrosion appears, clean the area with a fine steel wool pad, reapply wax, and hand Octagon Chrome Base buff the affected area. C52-221 (Figure 2) Triple Crown Assembly...
Page 9: Case, Mounting
From inside the cash box area on the back of the machine, install the four remaining "-20 bolts (14201B) through the bottom of the machine and secure with the nuts (1420N) [Figure 3]. Tighten using two " crescent wrenches. Triple Crown Assembly...
Page 10 (Figure 3) Machine Assembly Bolt (x4) 1420 IB Nut (x4) 1420 N Spill Tray Triple Crown Assembly...
Page 11: Delivery System
DELIVERY SYSTEM Triple Crown comes standard with deep, adjustable wheels (C6-411-23A) and brush housings (TC6-431) [Figure 4]. To set your deep, adjustable wheel, remove the two front and one back hold screws (Figure 8) from the housing with a phillips screwdriver.
Page 12 The Rocket Wheel will take gumballs up to 850 count. The 1" Capsule Wheel will take larger count gumballs and up to 1.25" capsules. Remember, your Triple Crown dumps product from the front of the machine. Set the delivery wheel into the product sleeve of the machine.
Page 13 To remove the lid, open and slide to the left when looking at the front of the unit. To replace the lid, align the pin in the lid with the hinge on the case and slide to the right. (Figure 9) Secure the Brush Housings with Hold Screws Triple Crown Assembly...
Page 14: Candy, Changing
Looking into the cash box you'll notice 3 small trap doors (Fig. 10), located on the underneath side of the product platform. To drain the product from the Triple Crown machine, simply place a container under the trap door and slide the door out to release the product into the container.
Page 15: Troubleshooting
TROUBLESHOOTING While The Triple Crown was built to be a trouble-free machine, you might find a minor problem you are not sure how to handle. The following chart lists some common areas of easily corrected problems. PROBLEM SOLUTION CAUSE Large, irregular shaped...
Page 16 Do not over-tighten. Inconsistent vends Timing of delivery wheel Be sure timing mark is visible in is not set properly. the timing slot. Every 3 vends the timing mark should be visible. Triple Crown Assembly...