Download Print this page

Dow GREAT STUFF PRO 13 Installation Information

Wall & floor adhesive dispensing gun

Advertisement

Quick Links

GREAT STUFF PRO
GREAT STUFF PRO
Wall & Floor
Adhesive is a heavy-duty adhesive
specially formulated to bond subfloors,
drywall, paneling, foam panels and most
construction materials. Different from
traditional adhesives because of its
excellent bonding power on dry, damp
and even frozen lumber, GREAT STUFF
PRO
Wall & Floor Adhesive provides
a fast-grab tack and long-term high-
strength bond. It bonds to lumber,
plywood, particle board, masonry,
drywall, concrete and foam panels.
It is an ideal choice for anchoring,
joining and stabilizing insulated
concrete forms and structural insu-
lated panels. GREAT STUFF PRO
& Cracks Insulating Foam Sealant can
be used to seal gaps in the forms and
prevent concrete leakage during the
pouring stage.
Materials Checklist
• GREAT STUFF PRO
Wall & Floor
Adhesive
• PRO Series foam dispensing guns
(Figure 1)
• Protective wear, including goggles,
gloves and proper clothing
• Dry cloth, putty knife or paint scraper
• GREAT STUFF PRO™ Gun Cleaner,
acetone, or other adhesive remover
I N S T A L L A T I O N I N F O R M A T I O N | United States /Canada | R E S I D E N T I A L
Wall & Floor Adhesive
Pro 13
Figure 1.
Safety and Conditions of Use
• Read the label and Material Safety Data
Gaps
Sheet carefully before use.
• GREAT STUFF PRO
Adhesive contains isocyanate and a
flammable blowing agent. Vapor may
travel to other rooms. Ensure adequate
ventilation. Shut off all pilot lights and
extinguish open flames; eliminate all
sources of ignition before use. Do not
smoke or use lighters or matches while
dispensing foam.
• Do not breathe vapor or mist. Use in
well-ventilated areas or wear proper
respiratory protection. Isocyanate is
irritating to the eyes, skin and respira-
tory system, and may cause sensitiza-
tion by inhalation or skin contact.
• GREAT STUFF PRO
Adhesive is very sticky and will adhere
to most surfaces and skin. Do not get
foam on skin. Wear gloves, and goggles
or safety glasses. Cured foam must be
mechanically removed or allowed to
wear off in time.
• The contents are under pressure. The
• GREAT STUFF PRO
Pro 14
Pro 15
Wall & Floor
Preparation
1. Remove all contaminants (water,
2. If the surface area has been previously
Wall & Floor
3. Whenever possible, allow any concrete
can may burst if left in areas suscepti-
ble to high temperatures, such as motor
vehicles, or near radiators, stoves or
other sources of heat. Do not lace can in
hot water. Do not puncture, incinerate
or store at temperatures above
120ºF (149ºC).
Wall & Floor
Adhesive should not be used around
heaters, furnaces, fireplaces, recessed
lighting fixtures or other applications
where the foam may come in contact
with heat-conducting surfaces. GREAT
STUFF PRO
foam will burn if exposed
to open flame or sparks from high
energy sources, and it will start to
thermally degrade if exposed to
temperatures above 240ºF (116ºC)
for long periods of time.
oil, dust, dirt, debris or other loose
materials or release agents) that may
affect the adhesion between the sub-
strates. If in doubt, conduct an adhe-
sion test, waiting at least one hour to
assess the bond.
painted, scrape away all loose or poorly
adhered paint and sand or thoroughly
roughen the surface. Conduct an
adhesion test if any previously painted
surfaces are to be bonded.
or masonry substrates to completely
cure before bonding.

Advertisement

loading
Need help?

Need help?

Do you have a question about the GREAT STUFF PRO 13 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dow GREAT STUFF PRO 13

  • Page 1 GREAT STUFF PRO Wall & Floor Adhesive ™ GREAT STUFF PRO Wall & Floor • The contents are under pressure. The ™ Adhesive is a heavy-duty adhesive can may burst if left in areas suscepti- specially formulated to bond subfloors, ble to high temperatures, such as motor drywall, paneling, foam panels and most vehicles, or near radiators, stoves or...
  • Page 2 4. Shake can vigorously for one minute 6. When changing cans, tighten the Application before dispensing or between uses. flow control knob before removing 1. Keeping can inverted, apply a 1/2” 5. Invert can and screw foam dispensing the empty can (Figure 4). Use GREAT (13 mm) bead of adhesive the full length gun firmly onto valve as shown in STUFF PRO...
  • Page 3 5. Mechanical fasteners must be installed • For long-term storage, unscrew can • Read the label and Material Safety soon after adhesive application in all and use GREAT STUFF PRO Gun Clean- Data Sheet carefully before use. ™ cases. Assemblies must be compressed er to clean uncured adhesive from the •...
  • Page 4 1-800-565-1255 (French) NOTICE: No freedom from infringement of any patent owned by Dow or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for determining whether products and the information in this document are appropriate for Customer’s use and for ensuring that Customer’s workplace and disposal practices are in compliance with applicable laws and other government enactments.

This manual is also suitable for:

Great stuff pro 14Great stuff pro 15