909 PH1000 Instruction Manual

800w pole chainsaw pruner

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

INSTRUCTION MANUAL

PH1000

800W

POL E

CH A INSAW PRUNER

Table of Contents

Need help?

Do you have a question about the PH1000 and is the answer not in the manual?

Questions and answers

Robert Peters

January 22, 2025

How do I order parts for a PH1000 Pole saw

Summary of Contents for 909 PH1000

Page 1 INSTRUCTION MANUAL PH1000 800W POL E CH A INSAW PRUNER...
Page 2: Table Of Contents
CONTENTS Warranty Warranty Power Tools Introduction For full details please visit us at www.909.com Environmental protection Specifications Description of symbols General safety instructions Additional safety rules for electric chainsaws Additional safety rules for pole trimmers General notes Unpacking Contents of carton...
Page 3: Environmental Protection
Manual before using your new 909 Power Tool. Take Read these instructions for use carefully. special care to heed the Cautions and Warnings. Your 909 power tool has many features that will make Wear safety footwear. your job faster and easier. Safety, performance, and Wear safety gloves.
Page 4: General Safety Instructions
General safety instructions f) If devices are provided for the connection of dust extraction and collection facilities ensure that these WARNING. Read and understand all instructions. are connected and properly used. Use of these Failure to follow all instructions listed below may result devices can reduce dust-related hazards.
Page 5: Additional Safety Rules For Electric Chainsaws
• Beware of wood splinters when cutting chopped wood. 4) Service • Ensure your chain saw is suitable for the job. a) Have your power tool serviced by a qualified repair personnel using only identical replacement parts. • Never work above shoulder level or reach out to cut a This will ensure that the safety of the power tool is branch: ensure you have stable footing at all times.
Page 6: General Notes
Danger! Due to modern mass production techniques, it is unlikely BEWARE OF KICKBACK! that your 909 Power Tool is faulty or that a part is missing. WARNING! Kickback can lead to dangerous loss of control If you find anything wrong, do not operate the tool until the of the chainsaw and result in serious or fatal injury to the parts have been replaced or the fault has been rectified.
Page 7: Know Your Product
Know your product 1. Motor housing 2. On/Off trigger switch 3. Lock off button 4. Main handle 5. Secondary handle 6. Shoulder strap 7. Main shaft 8. Extension shaft 9. Extension shaft clamp 10. Chain bar and chain 11. Oil tank 12.
Page 8: Assembly
Assembly This product has been shipped partially assembled. 1. Carefully remove the items from the box. Make sure that all items listed in the packing list are include. 2. Inspect the product carefully to make sure no breakage or damage occurred during shipping 3.
Page 9 8. Check that the chain can be smoothly pulled around the guide bar by hand and that it maintains contact with the guide bar, top and bottom. To check tension, rotate the chain to its tightest condition then suspend a 0.9kg weight from the chain at the mid point of the underside of the bar.
Page 10: Adding Chain Oil
Adding chain oil Changing of the saw chain WARNING. Never start work unless the chain and bar are ATTENTION: Always pull the power plug before lubricated. undertaking any maintenance work. 1. Place the chainsaw on its side with the oil cap facing up. The saw chain is full of sharp edges.
Page 11 9. Place the guide bar (10) in position over the threaded Important Notes: stud with the chain tensioning pin (23), in the hole in the 5. Clean oil and saw dust out of the area under the plastic guide bar. cover with a brush or blow it out with compressed air.
Page 12: Chain Tension
at the mid point of the Working with the pruner underside of the bar. Do not work with an angle higher than 60°. The pole saw The maximum distance will work under higher degrees, but there is the danger of between the driving links being injured by branches falling without warning.
Page 13: Chainsaw Maintenance
3. Fit the file in a file holder (not included) and place it over • Do not operate the chainsaw with the air intake on the the tooth at 35°. ground as this will draw foreign particles into the motor area and damage the windings of the motor.
Page 14: First Time User
Repairs beyond those described above, should only be undertaken by trained personal. Should a malfunction occur do not use the unit any further and do not attempt to repair it yourself. Contact 909 Customer Support or have the unit repaired by a professional.