Advertisement
Quick Links
LOR FOIL KIT 0.3
per pavimenti in legno e laminati
for wooden and laminate floors
DESCRIZIONE
LOR FOIL KIT 0.3 è un KIT completo per
il riscaldamento elettrico a pavimento
per
interni,
pavimenti in legno e laminato.
Il
kit
è
composto
isolante
di
0,3
robusta su cui è inserita la lamina V.
230,
un
cronotermostato
(modello
LOR-THERM
alimentazione,
terminazione.
La
posa
risulta
perché la pellicola si srotola come un
tappeto e può essere tagliata in base
alla superficie da coprire.
Non contiene alogeni o PVC.
!
Riscaldamento elettrico
Electrical heating
installabile
sotto
da
una
pellicola
mm
estremamente
digitale
355),
cavi
di
connessione
pratica
e
veloce
DESCRIPTION
LOR FOIL KIT 0.3 is a complete kit for
electric
underfloor
indoor, installed under wood flooring
and laminate.
The kit is composed of an insulating
film of 0.3 mm extremely robust (on
which is inserted the foil V. 230), a
digital
timer
(model
power
cables,
e
termination.
The
installation
because the film is unrolled like a
carpet and can be trimmed according to
the surface to be covered.
It does not contain halogens or PVC.
heating
for
LOR-THERM
355),
connection
and
is
quick
and
easy
1!
Advertisement
Summary of Contents for Lorenzoni Lor Foil Kit 0.3
- Page 1 Electrical heating for wooden and laminate floors DESCRIZIONE DESCRIPTION LOR FOIL KIT 0.3 è un KIT completo per LOR FOIL KIT 0.3 is a complete kit for il riscaldamento elettrico a pavimento electric underfloor...
-
Page 2: General Instructions
Installation instructions Lor Foil Kit 0.3 100 W Installation instructions Lor Foil Kit 0.3 100W Read carefully through all the installation instructions before starting the installation Before you start, compare the material in your Lor Foil Kit 0.3 with the table below. Contents Lor Foil Kit ARTICLE... - Page 3 Installation instructions Lor Foil Kit 0.3 100 W Preparing to lay the foil In addition to the Lor Foil Kit 0.3 you will need: • Non-ageing plastic film • Insulation 6 mm • Crimping tool • Earth fault relay – if not already installed in the building Remove any existing plastic matting.
-
Page 4: Getting Started
Installation instructions Lor Foil Kit 0.3 100 W Getting started Flexible Make space for the flexible conduit conduit Cut or chase a channel for the flexible conduit, as shown Thermostat in figure 5. The end of the flexible conduit must be po- sitioned centrally under a foil. - Page 5 Installation instructions Lor Foil Kit 0.3 100 W Seal off the copper strip Seal off the copper strip with the round green pieces of tape, as shown in figure 9. Seal only the short side that will not be connected with cable.
- Page 6 Installation instructions Lor Foil Kit 0.3 100 W Fit the terminals Slip the terminal on to the foil and centre it on the copper strip. Squeeze the terminal firmly with your fingers as shown in figure 13. Crimp the terminal from both sides at an angle of 45º...
- Page 7 Installation instructions Lor Foil Kit 0.3 100 W Connect the cables Connect the lengths of foil together with the single-core double-insulated RTK cables supplied. Strip off about 6 mm of insulation and insert the wire into the terminal. If there is only one cable, bend the stripped wire double, as shown in figure 17.
-
Page 8: Guarantee Certificate
Products at no cost to the purchaser. LORENZONI SRL Lorenzoni srl also undertakes to restore the floor to its original condi- MICHELE LORENZONI tion after the repair or replacement has been completed. In order to be... - Page 9 Installation instructions Lor Foil Kit 0.3 100 W Test Report Lor Foil Kit 0.3 Tolerance of resistance values: -5 to +10%. Min. Insulation value 10 Mohm. 230 V, 100W/m², width: 43 cm Before laying After fixing After floor covering 1322.5...
Need help?
Do you have a question about the Lor Foil Kit 0.3 and is the answer not in the manual?
Questions and answers