Summary of Contents for DNF Controls SW32PS-RCP
- Page 1 12843 Foothill Blvd. Suite C Sylmar, California 91342 V: 818.898.3380 F: 818.898.3360 sales@dnfcontrols.com Model No. SW32PS-RCP RS422 PORT SWITCHER REMOTE CONTROL PANEL User Manual Rev 1.01...
-
Page 5: Table Of Contents
KEYBOARD TEST b. SYSTEM PORT TEST REFERENCE . . . SPECIFICATIONS POWER CONNECTOR RS422 SERIAL CONNECTOR GPI CONNECTOR FRONT PANEL LAYOUT DNF CONTROLS LIMITED WARRANTY Manual Version ............1.01 090407 Document No: ......SW32PS-RCP_User_Manual.doc SW32PS-RCP Port Switcher Controller Page... -
Page 6: Revision History
1. REVISION HISTORY 080505 Original document. 090407 1.01 Corrected ID Switch numbering. SW32PS-RCP Port Switcher Controller Page... -
Page 7: Getting Started
“RS422” on the back of the SW32PS port switcher. Dip Switches Configuration for SW32PS-RCP. Every SW32PS-RCP has to have a unique ID from 1 to 10. The ID should match the External Device number set in the SW32PS. For example, if you use only one SW32PS-RCP with the SW32PS, the External Device should be set to 1 and the ID of the RCP should be 01. -
Page 8: Connection Diagram
“Power”. Then connect the IEC to Edison cable to the power supply. Connect the power cable to 90 VAC to 240 VAC source. Caution: Do Not Hot Plug the Power Supply DB9F connector! Installation is complete. 4. CONNECTION DIAGRAM TYPICAL CONNECTION DIAGRAM SW32PS-RCP Port Switcher Controller Page... -
Page 9: Operation
Press [PRESET]. The PRESET indicator will turn on. The first line of the display will show “Restore Preset 1”. Turn the Wheel to select preset number 1-8. Press [TAKE] to restore selected preset. Press [ESC] to exit without restoring. SW32PS-RCP Port Switcher Controller Page... -
Page 10: Setup Gang
Press [VIEW]. Turn the Wheel to find the GANG to be disconnected. Press [GANG]. The display will prompt “Disconnect switches?” Press [TAKE] to break all the routes that are part of gang. Press [ESC] to exit. SW32PS-RCP Port Switcher Controller Page... -
Page 11: Self-Test Procedure
Turn the Wheel to see Wheel count on the display change: (F0-00-10). SYSTEM PORT TEST Plug an RS422 looping plug into RS422 connector on the back of the SW32PS-RCP. The display should say: “port- OK”. Unplug the RS422 looping plug. SW32PS-RCP Port Switcher Controller Page... - Page 12 SW32PS-RCP Port Switcher Controller Page...
-
Page 13: Reference
POWER CONNECTOR 9-Pin D-Type, Male Pin # +5v DC Ground RS422 SERIAL CONNECTOR 9-Pin D-Type, Female Pin # 1 Frame Ground Receive Common Receive A Receive B Transmit B Transmit A Transmit Common Frame Ground Spare SW32PS-RCP Port Switcher Controller Page... -
Page 14: Gpi Connector
Input #3, No Function Input #4, No Function Input #5, No Function Input #6, No Function Input #7, No Function Ground + 5v + 5v No Connection No Connection No Connection No Connection No Connection Ground SW32PS-RCP Port Switcher Controller Page... -
Page 15: Front Panel Layout
8. FRONT PANEL LAYOUT Front Panel SW32PS-RCP Port Switcher Controller Page... - Page 16 SW32PS-RCP Port Switcher Controller Page...
-
Page 17: Dnf Controls Limited Warranty
DNF Controls, at its option, will repair or replace the defective unit. DNF Controls will return the unit prepaid to the customer. The method of shipment is at the discretion of DNF Controls, principally UPS Ground for shipments within the United States of America.
Need help?
Do you have a question about the SW32PS-RCP and is the answer not in the manual?
Questions and answers