Subscribe to Our Youtube Channel
Summary of Contents for Labgear LAB3522
- Page 1 User’s Manual 4CH DVR 4-Channel Standalone DVR Installation Guide & User’s Manual Version 3.60 — 0 —...
-
Page 2: Table Of Contents
User’s Manual 4CH DVR Directory DVR Feature......................Outlook ........................2.1. Front Panel...........................2 2.2. Rear Panel ...........................2 2.3. Remote Controller ........................3 DVR Installation ......................3.1. Install Hard Disk ........................3 3.2. Connect Camera and Monitor ....................4 3.3. Connect Power Cord ......................4 DVR System Boot..................... 4.1. -
Page 3: Dvr Feature
User’s Manual 4CH DVR 1. DVR Feature 4 Channel BNC camera input. 1 Channel BNC monitor. NTSC / PAL optional. Video loss prompt. Motion detection with area setting. One ATA-100 Hard Disk interface, support over 300GByte. Time Schedule record / Motion Triggered record. IR Remote Controller. -
Page 4: Remote Controller
User’s Manual 4CH DVR 2.3 Remote Controller 1.CH1 Select or enlarge CH1 2.CH2 Select or enlarge CH2 3.CH3 Select or enlarge CH3 4.CH4 Select or enlarge CH4 5.QUAD Quad View 6. REW Rewind 7.PLAY Play record 8.FWD Forward 9.RECORD Record or Increase Value 10.PAUSE Pause 11.STOP... -
Page 5: Connect Camera And Monitor
User’s Manual 4CH DVR 3.2 Connect Cameras and Monitor There are 4 cameras input and 1 monitor output with BNC connector. 3.3 Connect Power Cord Please use the power adapter supplied with DVR. 4. DVR System Boot 4.1 Detect Installed Hard Disk After connecting the power, system will boot-up HDD Checking……….. -
Page 6: Restore Recording Process
User’s Manual 4CH DVR 4.3 Restore Recording Process POWER ERROR DETECTED When power-error happened during recording RESTORE HARD DISK OK process, system will automatically restore RESTORE REC MODE…………… OK recording process after power Re-connected. 4.4 Main Screen First, start up the DVR. After system booting it will be sense of four cameras shown on the mo nitor. -
Page 7: Camera Select
User’s Manual 4CH DVR Menu Directory Camera Select Record Select Record Mode Record Frame Rate Main Menu Video Quality Auto Record Password Setup Record Schedule Password Change Sub Menu Picture Setup Time Setup Hard Disk Setup Language Setup Motion Setup Restore Factory Default 5.2 Camera Select DVR system can display 4 cameras and video... -
Page 8: Record Mode
User’s Manual 4CH DVR 5.4 Record Mode There are two modes for video recording, Each Mode： Compress and record each channel video separately, therefore, user can enlarge single channel video to full screen display. For example, user can turn off record function of CH1 and CH2 and then system only record CH3 and CH4 video. -
Page 9: Sub Menu-Auto Record
User’s Manual 4CH DVR λ “-” No Record. λ “T” Continue (System Default). λ “A” Motion Triggered. 「 Up」 「 Down」: Move the prompt. 「 Select」: Select Method. 5.8 Sub Menu-Auto Record When you choose “ON” DVR will be active to record automatically if DVR has not been operated in five minutes. -
Page 10: Sub Menu－Picture Setup
User’s Manual 4CH DVR 5.12 Sub Menu-Time Setup TIME SETUP ∨ 2007/01/18 08:30:00 Configure DVR system time. Press「 Up」and「 Down」to move prompt and press「 Select」 PRESS(UP,DOWN), THEN(SELECT) PRESS(MENU) TO EXIT to modify. Press「 Menu」to save and exit. 5.13 Sub Menu-Language Setup Press 「... -
Page 11: Ntsc/Pal Output Select
User’s Manual 4CH DVR MOTION RECORD DURATION: MOTION SETUP The number indicates how many seconds motioned MOTION RECORD DURATION MOTION ALARM DURATION recording lasts after the movements in front of the camera. MOTION DETECTION SETUP MOTION ALARM DURATION: PRESS(UP,DOWN), THEN(SELECT) The number indicates how many seconds motioned display PRESS(MENU) TO EXIT on the screen “... -
Page 12: Restore Factory Default
User’s Manual 4CH DVR 5.17 Restore Factory Default Press “EDIT” Button to make the system load factory default. 6. Record 6.1 Start Recording Press “ Record ” to start recording. System will display some information on Screen. Only EACH MODE can enlarge single channel to full screen display QUAD REC [M] (T) 2008/07/01 16:22:30... -
Page 13: Stop Recording
User’s Manual 4CH DVR 6.2 Stop Recording Press “ Stop” and if the order of “password setup” is ON, system will prompt to input password. Only correct password can stop recording process. 6.3 Force Record mode When the time correspond to the record schedule is “-”, please press the “Record” button once, and then hold the same button over 3 seconds, the DVR enter the force record mode, If you want to exit the force record mode, please press the “Stop”... -
Page 14: Playback
User’s Manual 4CH DVR User can calculate and estimate record hours by below formula 120G Byte @ 7 frames per second @ Normal quality 120 (G Byte) x 1024 (M Byte) x 1024 (K Byte) 15 (K Byte/frame) x 7 (frame/sec.) x 60 (sec.) x 60 (min.) Estimate hours is 332 Hours 7. -
Page 15: Specification
User’s Manual 4CH DVR 8. Specification ITEM DESCRIPTION NOTE Video Format NTSC / PAL Operation System None STAND-ALONE Camera Input Channel 4 channel Composite BNC Video Output Channel 1channel Composite BNC NTSC 120 frames/second 4 x 30 frames/second Display Frame Rate 100 frames /second 4 x 25 frames/second Recording Frame Rate... -
Page 16: Appendix
User’s Manual 4CH DVR 9. Appendix 9.1 System Connect Sketch Map Fittings Come Along With DVR 1. Power Adapter 1pcs 2. Power Cord 1pcs 3. Remote Control 1pcs 4. User Manual 1pcs — 15 —... - Page 17 User’s Manual 4CH DVR — 16 —...
Need help?
Do you have a question about the LAB3522 and is the answer not in the manual?
Questions and answers