Subscribe to Our Youtube Channel
Related Manuals for Clarke CRD1100
Summary of Contents for Clarke CRD1100
- Page 1 ROTARY HAMMER DRILL MODEL NO: CRD1100 PART NO: 6479610 OPERATION & MAINTENANCE INSTRUCTIONS LS1016...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE Hammer Drill. The CRD1100 is designed for general drilling/masonry drilling/chiselling/drill & hammer use in light industrial applications. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
-
Page 3: Safety Precautions
SAFETY PRECAUTIONS WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED BELOW REFERS TO YOUR HAMMER DRILL. WORK AREA 1. Keep work area clean and well lit. Cluttered and dark areas invite accidents. - Page 4 5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application.
- Page 5 SAFETY SYMBOLS Read instruction Wear dust mask manual before use Class 2 Double Wear ear defenders Insulated CE Mark Wear safety glasses Weee Directive ENVIRONMENTAL RECYCLING POLICY Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling &...
- Page 6 ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Connecting it to any other power source may cause damage.
- Page 7 OVERVIEW NO DESCRIPTION NO DESCRIPTION Depth Stop Rear Handle SDS Chuck Hammer On/Off Control Rotation On/Off Selector Switch Motor Brush Access Panel Grease Port Cover Front Handle Trigger Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 8: Before Use
BEFORE USE INSERTING A DRILL BIT / CHISEL The chuck clamps SDS drill bits and chisels without the need for a chuck key. 1. Pull back the collar. 2. Insert the bit. 3. Turn the bit in the chuck until it latches. - Page 9 POSITIONING THE FRONT HANDLE The front handle can be positioned left, right or centre as required. 1. Loosen the front handle by twisting it clockwise (when viewed from above). 2. Rotate the front handle to the required position. 3. Secure the front handle by twisting it anticlockwise (when viewed from above).
- Page 10 SELECTING THE OPERATING MODE Mode Hammer Action selector Rotation selector Drill Only Drill Only Hammer Drill Hammer Assisted Drilling Hammer only (no rotation) Hammer Assisted Drilling HAMMER ACTION SELECTOR 1. With the drill not operating, set the hammer action selector to the required setting.
- Page 11 USING THE DRILL BEFORE STARTING WORK 1. Before drilling into walls and floors etc., check first that there are no hidden electrical cables, gas or water pipes etc. 2. Check the mains voltage before plugging in and switching on. 3. Ensure the work area is as hazard free as possible. STARTING WORK 1.
- Page 12 DRILLING TIPS • Always use sharp, good quality drill bits. The performance of your drill is dependant on the quality of the bits used. • After drilling material to the full depth, do not simply pull out the drill but maintain chuck rotation to ease withdrawal.
- Page 13 CHANGING THE MOTOR BRUSHES 1. Remove the screw indicated and lift off the motor brush access panel. 2. Use a flat screwdriver to undo the cap. 3. Lift off the cap. 4. Lift out the brush and replace with a new one. 5.
- Page 14 MAINTENANCE AND SERVICING 1. After use, remove the drill bit and tap the side of the chuck to remove any dust or chippings etc. 2. Keep the handle clean and free from oil and grease. 3. Worn or damaged parts must be replaced by qualified personnel. 4.
-
Page 15: Specifications
SPECIFICATIONS Chuck capacity/type SDS plus 13mm keyed chuck adapter Rotational Speed 950 rpm Impact Rating (blows/min) 4200 Maximum Drilling Capacity: Wood - 40 mm Steel - 13 mm Concrete - 28 mm Sound Pressure Level 88.8dB LpA Sound Power Level 99.8 dB L Vibration Level Rotary hammer 17.914m/s... - Page 16 PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 17: Parts List
PARTS LIST ID DESCRIPTION DESCRIPTION Rubber Cap Piston Circlip Piston Pin Coller Connecting Rod Spring Steel Cover Chuck Housing Switch Assembly Oil Seal O-ring Circlip Hex Bolt Washer Gear Box Casing Bearing Grease Port Cover 10 Screw O-ring 11 Spring Washer Oil Seal 12 Flat Washer Gear Bevel... - Page 18 ID DESCRIPTION DESCRIPTION 61 Key Switch Assembly 62 Dome Pin Screw 63 Bearing Handle Left Side 64 Steel Cover Handle Right Side 65 Middle Cover Screw 66 Fan Cover Trigger 67 Bearing Screw 68 Rotor Screw 69 Stator Capacitor 70 Bearing Cable Clamp 71 Main Housing Inductor...
- Page 19 DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CRD1100 and is the answer not in the manual?
Questions and answers