Page 1 OPEL ZAFIRA TOURER Infotainment System...
Page 3 Contents Navi 950/650 / CD 600 ....5 Navi 900/600 / CD 400plus/ 400/300 ........77...
Page 5 Navi 950/650 / CD 600 Introduction ........6 Basic operation ......16 Radio ........... 24 CD Player ........30 External devices ......32 Navigation ........39 Speech recognition ...... 58 Phone .......... 62 Index ..........72...
Page 6: Introduction
Introduction Introduction General information Optionally, the Infotainment system can be operated using the instrument The Infotainment system provides panel controls, the controls on the you with state-of-the-art in-car steering wheel or the speech infotainment. recognition function. General information ....... 6 The radio can easily be used by The well-thought-out design of the Theft-deterrent feature ....
Page 7 Introduction doubt, stop the vehicle and may issue a warning that must be operate the Infotainment system accepted. Therefore, pay while the vehicle is stationary. particular attention to one-way streets and other roads and entrances that must not be driven 9 Warning into.
Page 8 Introduction Control elements overview Navi 950 / 650...
Page 9: Table Of Contents
Introduction ; button CD/MP3/WMA: skip track 12 CONFIG button forwards ........ 31 Open settings menu ....21 Access Home Page ....16 External devices: skip 13 INFO button Station buttons 1...6 track forwards ....... 34 Radio: information on Short press: select station ..26 T button current station Long press: save station ..
Page 10 Introduction 16 BACK button FM ......... 24 Menu: one level back .... 16 DAB ........24 Input: delete last character or entire entry ......16 17 RPT / NAV button Repeat last navigation message ....... 53 18 CD slot ........31 19 O button Take phone call or activate/deactivate mute ..
Page 11 Introduction CD 600...
Page 12 Introduction ; button FAV 1-2-3 button 12 Multifunction knob Open favourites list ....26 Turn: mark menu options Access Home Page ....16 or set alphanumeric values . . 16 AS 1-2 button Station buttons 1...6 Press: select/activate the Short press: open Long press: save station ..
Page 13 Introduction 18 SRCE (Source) button Steering wheel audio controls If radio is active: turn up/ down to select next/ Press to toggle through the previous preset radio different audio sources station ........24 CD/MP3 player ...... 30 If CD player is active: turn up/down to select next/ USB ........
Page 14 Introduction Usage or close call list ...... 65 Automatic switch-off If the Infotainment system is switched or activate/deactivate mute ... 14 on using the X knob while the ignition Control elements is switched off, it switches off again or deactivate speech The Infotainment system is operated automatically after 10 minutes.
Page 15 Introduction Mute ■ Bluetooth audio 3 32 Press the O button (if Phone portal ■ AM radio 3 24 is available: press for a few seconds) ■ FM radio 3 24 to mute the audio sources. ■ DAB radio 3 29. To cancel mute again: turn the X VOL knob or press the O button Navigation...
Page 16 ■ To mark a menu option. System settings ......21 ■ To set an alphanumeric value. Press the multifunction knob (Navi 950 / Navi 650: press the outer ring): Using the multifunction knob, you may then access the different ■ To select or activate the marked applications.
Page 17 Examples of menu operation Press the multifunction knob (Navi 950 / Navi 650: press the outer Selecting a screen element If there are more menu items ring) to display the second Home...
Page 18 Basic operation Adjusting a setting Press the multifunction knob to The last character in the character activate the menu item. A checkmark sequence can be deleted using the or a point appear within the box or ring Del screen button or the BACK beside the respective menu item.
Page 19: Basic Operation
Basic operation Treble Use this setting to enhance or attenuate the high frequencies of the audio sources. Adjust the setting as desired. EQ mode (EQ: Equaliser) Use this setting to optimise the tone for a specific style of music, e.g. Rock or Classical.
Page 20: Volume Settings
Basic operation Press the CONFIG button and then Adjusting the Startup Volume select the Radio Settings menu item. Press the CONFIG button and then select the Radio Settings menu item. Select the Audio Cue Options menu item. Select Startup Volume to display the respective menu.
Page 21: System Settings
Basic operation Adjusting the Chime Volume To adjust the volume of the audio Language settings source possibly playing in the When operating the controls in the Press the CONFIG button and then background, select Background and vehicle, beeping sounds confirm your select the Languages menu item.
Page 22: Software Information
Basic operation Set time Software update To access the menu from the Home Page, select the Menu screen button To adjust the time settings, select the To update your system software, at the bottom of the screen. Set Time menu item. Adjust the contact your Opel Service Partner.
Page 23 Basic operation Scroll to the position on the home page where you wish the icon to be located. Press the multifunction knob to confirm. The icon is moved to the new location. The icon that was located in that position before is now displayed in the position of the moved icon.
Page 24 Radio Radio Usage Manual station tuning In the FM and DAB waveband, press Activating radio the multifunction knob to open the respective menu and then select Press the ; button and then select Usage .......... 24 Manual tuning. The frequency the AM, FM or DAB icon.
Page 25: Station Search
Radio Note Some stations also change the PTY Updating the station lists If no station list has been created code depending on the content which If the stations stored in the waveband- beforehand, the Infotainment is currently transmitted. specific station list can no longer be system performs an automatic received, the AM and the DAB station The Infotainment system stores these...
Page 26: Favourite Lists
Radio Storing stations manually Stations can also be stored manually in the autostore lists. Set the station to be stored. Press the AS button to open the autostore list or to switch to another autostore list. To store the station in a list position: press the corresponding station button 1...6 until a confirmation message is displayed.
Page 27: Radio Data System (Rds)
Radio Retrieving a station Advantages of RDS If required, briefly press the FAV ■ On the display the programme button to open a favourite list or to name of the set station appears switch to another favourite list. Press instead of its frequency. one of the station buttons 1...6 to ■...
Page 28 Radio If Regional is deactivated, alternative Radio traffic service Traffic Volume frequencies of the stations are To adjust the volume of traffic (TP = Traffic Programme) selected without regard to regional announcements, select the Traffic Radio traffic service stations are RDS programmes.
Page 29: Digital Audio Broadcasting
Radio If you wish the time and date settings ■ As long as a given DAB receiver background and continually to be updated automatically, activate can pick up the signal sent out by a searches for the best receivable FM the RDS Auto Time Adjust menu item.
Page 30: Cd Player
CD Player CD Player General information MP3 CDs The following file formats can be used: ISO9660 Level 1, Level 2, Important information about (Romeo, Joliet). audio CDs and MP3/WMA CDs General information ..... 30 MP3 and WMA files written in any The Infotainment system's CD player format other than listed above may Usage ..........
Page 31: When An Audio Source Is Already
CD Player Usage Depending on the data stored on the Function buttons audio CD or MP3 CD, more or less Skipping to previous or next track detailed information on the CD and Starting CD playback the current music track are shown on Press the t or v buttons once or Push the CD with the labelled side the display.
Page 32: External Devices
External devices External devices General information When connected to the AUX input, the audio signal of the auxiliary device Sockets for the connection of external is transmitted via the speakers of the devices are located in the centre Infotainment system. console on a hinged panel.
Page 33 External devices When connected to the USB port, the File formats Caution devices mentioned above can be Audio files operated via the controls and menus Avoid disconnecting the device of the Infotainment system. Only devices formatted in the FAT32, during playback. This may NTFS and HFS+ file systems are Note damage the device or the...
Page 34: Playing Audio
External devices Gracenote Example: USB main menu Pausing playback Press the T button to pause The Gracenote database contains playback. information on media data currently available on the market. Audio menus When connecting external devices, To display the respective audio the tracks or files are recognised by menu, press the multifunction knob.
Page 35: Function Buttons
External devices To play the tracks on the respective To delete a playlist generated by the device in random order, activate the system, select the Delete Automatic Shuffle menu item. Playlist menu item. A list of all generated playlists is displayed. To return to the normal playing order, Select the playlist you wish to delete.
Page 36 External devices Slide show Slideshow Timer Activating the Tethering function To start a slideshow of all pictures To adjust the time sequence in which on the smartphone stored in the respective picture folder, one picture is shown during a slide Activate the Tethering and the select the 6 screen button at the show, select the Slideshow Timer...
Page 37 External devices Then a keyboard for the entry of an Select the desired app. A submenu email address is displayed. Enter with detailed information on the To display a list of all apps available, your email address. respective app is displayed. select the All screen button at the bottom of the screen.
Page 38 External devices Settings The settings menu provides options for the management of the accounts. Press the ; button and then select the Apps icon to display the apps main menu. Select the Settings screen button at the bottom of the screen to display the respective submenu.
Page 39: Navigation
Navigation Navigation General information followed. If a navigation instruction contradicts traffic regulations, the The navigation application will reliably traffic regulations always apply. guide you to your destination without the need to read maps. General information ..... 39 Functioning of the navigation The current traffic situation is taken Usage ..........
Page 40 Navigation Route guidance is provided by voice If route guidance is not active, the Route guidance active commands and a direction arrow, as following information is displayed: well as with the aid of a multi-colour ■ In the top line: information on the map display.
Page 41 Navigation ■ Current position: indicated by a red Map manipulation Changing the map mode triangle within a grey circle. The map may be displayed in three Moving the visible map section (route guidance not active), ■ Route: indicated by a blue line. The visible map section on the map respectively five (route guidance ■...
Page 42 Navigation Map modes Map display Changing screen information Press the multifunction knob to Press the multifunction knob to The route information displayed on display the Navigation Menu. Select display the Navigation Menu. Select the screen during active route the Map Modes menu item to display the Map Settings menu item and then guidance may be customised.
Page 43 Navigation Position information Saving a position Use Last Known Position To set the last position provided by a The current position or a destination Current position GPS signal as starting point, select position may be saved in the address the Use Last Known Position menu Press the multifunction knob to book.
Page 44 Navigation Select the Cancel Route Simulation menu item. Additional route simulation menu When route guidance is active in the simulation mode, an additional menu is displayed in the Navigation Menu. Press the multifunction knob to display the Navigation Menu. Scroll through the list and select the Route Simulation menu item to display the respective submenu.
Page 45 Navigation Note To enter special characters not The house number entered must available on the letter keyboard, have as many digits as the biggest select the ÄÖ screen button at the house number in the respective right side of the letter keyboard. The street, e.g.
Page 46 Navigation To manually display a list of matching Press the DEST / NAV button to Select the Category entry field to entries for the current input, select the display the Destination Entry menu display a POI category list. Select the respective List screen button at the and then select the Points of Interest desired category and then a...
Page 47 Navigation Telephone number search mask Previous Destinations Enter or select the desired address. Select the Country entry field to The confirmation menu is displayed. The last destinations selected or display a list of all available countries. entered for route guidance are stored Select the desired country.
Page 48 Navigation If activated 3 40, the address book entries are indicated on the map by POI icons. To change the icon indicating an address entry, select the Icon entry field. A list of all POI icons available within the system is displayed.
Page 49 Navigation Make your changes and confirm your Destination selection from the input. The changes are stored in the address book. Destinations (addresses or POIs) may also be set via the map. Phone Book Press the NAV button to display the Addresses stored in the phone book map.
Page 50 Navigation A confirmation menu is displayed. Selecting the home address Select the Start Guidance menu item Press the DEST / NAV button to to start route guidance. display the Destination Entry menu and then select the My Home icon. Note Route guidance to the home address If there is more than one POI located is started immediately.
Page 51 Navigation Select the Add screen button at the Moving waypoints The waypoint route is saved. position where you wish to add a To change the order of the waypoints Creating new favourite routes waypoint. The Destination Entry in the route, select the Sort Press the DEST / NAV button to menu is displayed.
Page 52 Navigation Selecting a favourite route Press the DEST / NAV button to display the Destination Entry menu and then select the Favourite Routes icon to display a list of the favourite routes saved. Select the desired route from the list. The route confirmation menu is displayed.
Page 53 Navigation To start route guidance, select the Voice prompts Start Guidance menu item. Navigation voice prompts announce which direction to follow, when Deleting saved destinations approaching an intersection at which To delete destinations stored in the you need to turn. system, press the CONFIG button, Press the CONFIG button and then select the Navigation Settings menu...
Page 54 Navigation Select Volume Test to get an audio Traffic incidents Choose between Automatic example of the settings. Recalculation and Recalculation after The TMC traffic information system Confirmation of a corresponding receives all current traffic information Guidance alerts message. from TMC radio stations. This Guidance alerts show in a close-up information is included in the Traffic incidents on the map...
Page 55 Navigation TMC stations To display a list of the traffic events The TMC stations broadcasting traffic concerning the current route, select information, may be set automatically the Traffic Events on Route menu or manually. item. Select the Traffic Stations menu item The traffic incidents lists may be to display a selection mask.
Page 56 Navigation To display a list of all tracking Turn List Avoid List sessions, select the Saved screen The Turn List displays all streets and When streets have been excluded button. Select the desired tracking turning manoeuvres on the calculated from the original route, they are session to display the Bread Crumb route starting from the current displayed in the Avoid List.
Page 57 Navigation Exit list To display a list of the next exits and motorway stations while driving on a motorway, press the NAV button and then press the multifunction knob to display the Navigation Menu. Scroll through the list and select the Exit List menu item.
Page 58: Speech Recognition
Speech recognition Speech recognition General information In the first command, you indicate the type of action to be performed, e.g. The speech recognition of the "Navigation destination entry". The Infotainment system enables you to system replies with prompts that lead operate various functions of the you through a dialogue for entering General information .....
Page 59: Phone
Speech recognition In such a case you need to select For changing the display language, The audio system mutes, the w another language for the display if see "Language" in chapter "System symbol on the display is highlighted, you want to control the Infotainment settings"...
Page 60 Speech recognition Interrupting a voice prompt Operation via speech song name, or "Tune to" followed by the radio frequency and the commands As an experienced user, you can waveband. interrupt a voice prompt by briefly The speech recognition can pressing the w button on the steering Navigation destinations, however, understand commands that are either wheel.
Page 61 Speech recognition Selecting list items The "Help" command When a list is displayed, a voice After saying "Help", the help prompt prompt asks to confirm or select an for the current dialogue step is read item from that list. A list item may be aloud.
Page 62 Phone Phone General information Important information for operation and traffic safety The Phone portal provides you with the possibility of having mobile phone 9 Warning conversations via a vehicle General information ..... 62 microphone and the vehicle Mobile phones have effects on Bluetooth connection ....
Page 63 Phone Via the Bluetooth menu, pairing (PIN Bluetooth menu phones is prohibited, if code exchange between Bluetooth To open the Bluetooth menu, you interference is caused by the device and Infotainment system) and may optionally: mobile phone or if dangerous connecting of the Bluetooth devices situations can occur.
Page 64 Phone A six-digit PIN code for the pairing Device list Deleting a device process is displayed on the Select the device you wish to delete. The device list contains all Bluetooth Infotainment system. A submenu is displayed. devices paired to the Infotainment system.
Page 65 Phone Answer when the service personnel Not every telephone supports all 9 Warning questions you about the emergency. functions of the phone application. Therefore, deviations from the range Bear in mind that you can make 9 Warning of functions described are possible. and receive calls with the mobile phone, if it is in a service area with Phone main menu...
Page 66 Phone Phone book Press the O button and then select the Phone Book menu item. The Phone Book Search menu is displayed. Enter the desired number. Select the desired entry in the telephone book to display the Select the Del screen button or press numbers saved under this entry.
Page 67: Incoming Calls
Phone Call lists Press the O button and then select the Call Lists menu item. The Call Lists menu is displayed. Ending a phone call To take the call, select the Answer To end the call, select the Hang up screen button.
Page 68 Phone Text messages To transfer the call back to the Infotainment system, select the As soon as a connection via Transfer call menu item in the Private Bluetooth has been set up between Call menu. your mobile phone and the Infotainment system, you can operate Second phone call the messages inbox of your mobile...
Page 69 Phone The Messages icon in the Home Reply menu of the Infotainment system is To directly answer the message, then selectable. select the Reply screen button. A list of predefined messages is displayed. Incoming text message Select the desired message and When a new text message is confirm your input.
Page 70 Phone Mobile phones and CB Seek advice on predetermined Caution installation points for the external radio equipment antenna or equipment holder and Mobile telephones and radio ways of using devices with a Installation instructions and equipment may lead to transmission power exceeding operating guidelines malfunctions in the vehicle 10 watts.
Page 71 Phone...
Page 72: Index
Index Activating AUX......34 Category list........24 Activating Bluetooth music... 34 CD player........30 Activating CD player..... 31 Chime volume....... 20 Activating radio......24 Control elements Activating the Infotainment system 14 Infotainment system....8 Activating the navigation system. . 40 Steering wheel......
Page 73 Audio files........32 Menu operation......16 Turn list........53 Picture files........ 32 Messages........16 Voice prompts......53 Midrange........19 Waypoint trip......44 Mobile phones and CB radio Navigation system......39 General information 30, 32, 39, 58, 62 equipment ........ 70 Navigation volume......
Page 74 Phone call Route guidance......53 Treble........... 19 Initiating........65 Route simulation......40 Turn list......... 53 Taking........65 Picture files........32 Software update......21 Usage....14, 24, 31, 40, 59 Pictures......... 35 Speech recognition....... 58 AUX........... 34 Playing audio........ 34 Station list........24 Bluetooth music......
Page 75 Waveband selection..... 24 Waypoint trip......... 44...
Page 77 Navi 900/600 / CD 400plus/400/300 Introduction ........78 Radio ......... 102 CD Player ........118 AUX input ........124 USB port ........126 Digital picture frame ....130 Navigation ........133 Speech recognition ....178 Phone ........192 Index .......... 210...
Page 78 Introduction Introduction General information to your destination, and, if desired, will automatically avoid traffic jams or The Infotainment system provides other traffic problems. you with state-of-the-art in-car Optionally, the Infotainment system infotainment. General information ..... 78 can be operated using controls on the For the AM, FM and DAB (if available) steering wheel, or via the speech Theft-deterrent feature ....
Page 79 Introduction Theft-deterrent feature Important information on 9 Warning operation and traffic safety The Infotainment system is equipped In some areas one-way streets with an electronic security system for 9 Warning and other roads and entrances the purpose of theft deterrent. (e.g.
Page 80 Introduction Control elements overview Navi 600 / Navi 900...
Page 81: Station Buttons 1
Introduction RADIO (BAND) ....102 Search forward ....102 11 TP ........111 Activate radio or change Radio: search forward ..102 Activate or deactivate waveband ......102 radio traffic service ....111 CD/MP3/WMA: skip track CD/AUX ......118 12 CD ejection ......120 forward ........
Page 82 Introduction 15 Multifunction knob ....90 21 NAV ........134 Turn: mark menu options Press once: Display map ... 134 or set numeric values ... 90 Press twice: Navigation Press (the outer ring): menu ........134 select/activate the marked option; confirm set value; switch function on/off ....
Page 83 Introduction CD 400 / CD 400plus...
Page 84: Short Press: Select Station
Introduction RADIO (BAND) ....102 FAV (1/2/3) ......104 12 INFO ........80 Activate radio or change Lists of favourites (preset Radio: information on the waveband ......102 radio stations) ..... 104 currently played station ..102 CD ........118 AS (1/2) .......
Page 85 Introduction 18 AUX ........124 Change to external audio source ......... 124...
Page 86 Introduction CD 300...
Page 87: Cd/Mp3/Wma: Skip Track Backwards
Introduction RADIO (BAND) ....102 Radio station buttons 1...6 . 103 14 INFO ........80 Activate radio or change Long press: save station ..103 Radio: information on the waveband ......102 currently played station ..102 Short press: select station . . 103 CD ........
Page 88 Introduction 20 AUX ........124 Steering wheel audio controls If radio is active: turn upwards/downwards to Change to external audio select next/previous source ......... 124 preset radio station ..... 102 If CD player is active: turn upwards/downwards to select next/previous CD/ MP3/WMA track ....
Page 89 Introduction Usage Setting the volume To cancel mute again: turn the X knob or press the v/G button again Turn the X knob. The current setting (if Phone portal available: press for a Control elements is shown on the display. few seconds).
Page 90 Introduction Audio players Press the multifunction knob to open BACK button a submenu with options for the input Press the CD/AUX button to open the Press the BACK button briefly to: or selection of numbers. CD, USB, iPod or AUX menus (if ■...
Page 91 Introduction Turn the multifunction knob to move Setting a value Switching a function on or off the cursor (= coloured background) to the desired option. Press the multifunction knob to select the marked option. Submenus An arrow on the right-hand edge of the menu indicates that after selection of the option a submenu with further options will be opened.
Page 92 Introduction Entering a character sequence CD 400 / CD 400plus Activating a setting Selecting an option To enter character sequences, e.g. Turn the multifunction knob to mark telephone numbers or road names: the desired setting. Turn the multifunction knob to move the cursor (= coloured background) to Turn the multifunction knob to select Press the multifunction knob to...
Page 93 Introduction Setting a value Switching a function on or off Entering a character sequence Turn the multifunction knob to change Turn the multifunction knob to mark For the input of character sequences, the current value of the setting. the function to be switched on or off. e.g.
Page 94 Introduction CD 300 The arrow pointing to the right (3) Setting a value indicates: the first submenu level is Menu elements and symbols active (two arrows = second submenu level active). The down arrow (4) indicates: further options are available in the active submenu.
Page 95 Introduction Tone settings Switching a function on or off Entering a character sequence Navi 600 / Navi 900 In the tone settings menu the tone characteristic can be set differently for each radio waveband and each audio player source. Press the multifunction knob to open Press the multifunction knob to open the corresponding settings menu.
Page 96 Introduction Setting bass, middle and treble Setting the volume distribution Setting the volume distribution between front - rear between right - left Select Bass, Middle or Treble. Select Fader. Select Balance. Set the desired value for the option selected. Set the desired value. Set the desired value.
Page 97 Introduction Optimising the tone for the style of Select Bass:, Midrange: or Treble:. music Set the desired value for the selected option. Setting the volume distribution between front - rear Press the TONE button to open the tone menu. Select EQ (Equalizer). Setting bass, middle and treble The displayed options offer optimised bass, middle and treble presettings...
Page 98 Introduction Volume settings Setting the volume distribution Optimizing the tone for the style of between right - left music Navi 600 / Navi 900 Maximum startup volume Select Balance:. Select EQ: (Equalizer). Set the desired value. The displayed options offer optimized bass, middle and treble presettings Setting an individual setting to “0”...
Page 99 Introduction Speed dependent volume Volume of the traffic announcements CD 300 / CD 400 / CD 400plus (TA) Maximum startup volume The volume of the traffic announcements can be increased or reduced proportionately to the normal audio volume. Press the CONFIG button to open the system settings menu.
Page 100 Introduction Personalisation Speed compensated volume Volume of the traffic announcements (TA) (only CD 400plus) The volume of the traffic Various Infotainment system settings announcements can be increased or can be separately memorised for reduced proportionate to the normal each vehicle key (driver) of the car. audio volume.
Page 101 Introduction ■ last position in Audio/MP3 CD including track number and folder ■ state of shuffle songs setting (CD player) ■ state of TP (Traffic Programme) setting ■ cursor position for each menu on the display Activating/deactivating personalization Press the CONFIG button to open the system settings menu.
Page 102 Radio Radio Usage Station search Control buttons Automatic station search The most important buttons for Briefly press the button s or u Usage ........102 control of the radio are as follows: to play the next station in the station Station search ......
Page 103 Radio Note DAB waveband Note Manual station search: If the radio The currently received station is (not available for CD 300 / CD 400) does not find a station, it switches highlighted. Press the multifunction knob to open automatically to a more sensitive the DAB menu and select DAB CD 400 / CD 400plus: search level.
Page 104 Radio Automatic station storing Retrieving a station 6 stations can be stored in each favourite list. The number of available Press and hold the AS button until an Briefly press the AS button to open an favourite lists can be set (see below). autostore message is displayed.
Page 105 Radio Defining the number of available CD 300 / CD 400 / CD 400plus To store the station in a list position: favourite lists press the corresponding station button 1...6 until a confirmation message is displayed. Retrieving a station Briefly press the FAV button to open a favourite list or to switch to another favourite list.
Page 106 Radio Press the CONFIG button. Navi 600 / Navi 900 Select Radio settings and then Radio favourites. Select the desired number of available favourite lists. Waveband menus Alternative facilities for station selection are available via waveband specific menus. With the radio main menu active, Select the required station.
Page 107 Radio Turn the multifunction knob. Updating station lists once in the station list at a sudden change in reception area. In such If the stations stored in a waveband- All receivable DAB stations 3 115 in circumstances, the updating of the specific station list can no longer be the current reception area are station lists can be accelerated using...
Page 108 Radio The currently received DAB service (programme) is interrupted when any announcements of previously activated categories are pending. Activating announcement categories Select DAB announcements in the DAB menu. A list of programme types available at Select the required station. the moment is displayed. The category list is also updated Select desired programme type.
Page 109 Radio CD 300 / CD 400 / CD 400plus All receivable DAB stations 3 115 in the current reception area are displayed. Note If no station list has been created beforehand, the Infotainment system performs an automatic station search. Select the required station. Note Favourites list The currently received station is...
Page 110 Radio If the stations stored in a waveband- The Infotainment system stores these specific station list can no longer be stations, sorted by programme type, received: in the corresponding category list. Select the corresponding command To search for a programme type to update a station list.
Page 111 Radio Radio data system (RDS) The currently received DAB service Navi 600 / Navi 900 (programme) is interrupted when any RDS is a service of FM stations that announcements of previously considerably facilitates the finding of activated categories are pending. the desired station and its fault-free Activating announcement categories reception.
Page 112 Radio If regionalization is switched on, only TA volume alternative frequencies (AF) with the The volume of the traffic same regional programmes are announcements (TA) can be preset selected. 3 98. If regionalization is switched off, Radio traffic service alternative frequencies of the stations (TP = Traffic Programme) are selected without regard to Radio traffic service stations are RDS...
Page 113 Radio ■ If a radio traffic service station has EON (Enhanced Other Networks) Select Radio settings and then RDS been found, [TP] is indicated on the With EON you can listen to radio options. display in black. If no radio traffic traffic announcements even if the CD 300: Select Audio settings and service stations are found, TP is...
Page 114 Radio Note RDS-scrolling text Switching the radio traffic service on If RDS is switched off, it will be Some RDS stations hide the and off automatically switched on again programme name in the display line To switch the traffic announcement when a radio station is changed (by in order to display additional standby facility of the Infotainment...
Page 115 Radio Listening to traffic announcements Digital audio broadcasting (DAB) is CD 400plus: only an innovative and universal Switch on the radio traffic service and broadcast system. completely turn down the volume of DAB stations are indicated by the the Infotainment system. programme name instead of the broadcasting frequency.
Page 116 Radio ■ As long as a given DAB receiver improved, whereas AM or FM Configuring DAB can pick up the signal sent out by a reception is considerably impaired Navi 600 / Navi 900 broadcasting station (even if the in such cases. signal is very weak), sound ■...
Page 117 Radio can be raised to a point where the The following options are available in can be raised to a point where the quiet sounds are audible, without the configuration menu: quiet sounds are audible, without the loud sounds being too loud. the loud sounds being too loud.
Page 118 CD Player CD Player General information ■ Self-recorded CD-Rs and CD-RWs are more vulnerable to mishandling than prerecorded CDs. Correct Navi 600 / Navi 900 handling, especially in the case of The Infotainment system's CD player self-recorded CD-Rs and CD-RWs, General information ....
Page 119 CD Player Maximum folder structure depth: Important information about audio names and folder names may not 11 levels. CDs and MP3/WMA CDs be displayed correctly. Maximum number of MP3/WMA Note Caution files that can be saved: 1000. ISO 13346 is not supported. It may be required to manually select ISO WMA files with Digital Rights Under no circumstances place...
Page 120 CD Player ■ Avoid leaving fingerprints when you Applicable playlist Starting CD replay change CDs. extensions: .m3u, .pls, .asx, .wpl. Push CD with the labelled side upward into the CD slot until it is ■ Put CDs back in their sleeves ■...
Page 121: Forwards
CD Player Skipping to the next track or previous Selecting tracks using the audio CD During MP3 replay track or MP3 menu Briefly press button s or u once During audio CD replay or several times. Track search forward or backward Briefly press button s or u and then press and hold s or u again until the desired track is...
Page 122 CD Player CD 300 / CD 400 / CD 400plus Inserting a CD Insert a CD with the printed side facing up into the CD slot until it is drawn in. Changing the standard page view (only CD 300) During audio CD or MP3 replay: press the multifunction knob and then select Default CD page view or Default MP3 page view.
Page 123 CD Player Selecting tracks using the audio CD During MP3 replay To open a menu with additional or MP3 menu options for track search and selection (only CD 400plus): select Search. During audio CD replay What options are available depends on the data saved on the MP3 CD.
Page 124: Aux Input
AUX input AUX input General information In the centre console on a hinged panel there is an AUX socket for the connection of external audio sources. General information ....124 Usage ........125 CD 300 / CD 400 / CD 400plus: Navi 600 / Navi 900: It is possible, for example, to connect a portable CD player with a 3.5 mm...
Page 125 AUX input Note The socket must always be kept clean and dry. Usage Press the CD/AUX button once or several times to activate the AUX mode. Navi 600 / Navi 900: An audio source that is connected to the AUX input can be operated only via the control elements of the audio source.
Page 126: Usb Port
USB port USB port General information Navi 600 / Navi 900 In the centre console on a hinged panel there is a USB socket for the connection of external audio data General information ....126 sources. Playing saved audio files ... 128 Note The socket must always be kept clean and dry.
Page 127 USB port Important information Applicable playlist Note extensions: .m3u, .pls The socket must always be kept MP3 player and USB drives clean and dry. ■ The MP3 players and USB drives Playlist entries must be in the form connected must comply with the of relative paths.
Page 128 USB port Playing saved audio files iPod iPod functions Navi 600 / Navi 900 MP3 player / USB drives Press the CD/AUX button once or Depending on the data saved, there several times to activate the audio are various options for the selection iPod mode.
Page 129 USB port CD 400plus Operation and the screen displays The search process on the USB are described for USB drives only. device may take several minutes. Operation of other devices like iPod During this time the station last played or Zune is mainly the same. will be received.
Page 130 Digital picture frame Digital picture frame General information ■ Only pictures in JPEG standard format (file extensions, e.g., .jpg Using the digital picture frame or .jpeg) are supported. function (only Navi 600 / Navi 900) Example: "F:\myPicture.jpg", you can view your favourite pictures General information ....
Page 131 Digital picture frame Press the CONFIG button, select Display settings, and then select Picture frame. The menu shown below is displayed. The menu shows a list with the file Select max. 10 pictures that you want names of all pictures (note the to be downloaded (added) to the restrictions described in "Important Infotainment system's memory or...
Page 132 Digital picture frame Press the CONFIG button, select As long as a picture stays selected in Display settings, select Picture the Picture selection menu, it can be frame, and then select Picture displayed at any time using the selection. The menu shown below is INFO button.
Page 133 Navigation Navigation General information followed. If a navigation instruction contradicts traffic regulations, the The navigation system will reliably traffic regulations always apply. guide you to your destination without the need to read maps, even if you General information ....133 Functioning of the navigation have no local knowledge whatsoever.
Page 134 Navigation The route guidance is provided by Dynamic route guidance only works if display (if route guidance active) and voice output and an arrow, as well as traffic information is received via the split screen display, see "Information with the aid of a multi-colour map TMC traffic information system.
Page 135 Navigation Adjusting the volume of route If route guidance is not active, the Route guidance active guidance messages while they are following information is displayed: If route guidance is active, the announced: turn the X knob. following information is displayed ■...
Page 136 Navigation ■ A small arrow representing the next Distances to the next service areas, but one driving recommendation. parking areas, intersections and/or exits on the highway. ■ Distance to the next intersection. ■ When reaching a highway ■ Streets leading off the current intersection information regarding street to follow.
Page 137 Navigation On the right side of the display the Note following information is shown: To change to full map display: press NAV button twice. ■ A compass symbol that indicates the north direction. Setting up the navigation ■ If no GPS signal (see chapter system "General information"...
Page 138 Navigation Sort criteria Import individual POIs To remove all imported POIs of a Select whether traffic messages are certain category: import an empty Only applicable if a USB drive with to be displayed in an order based on POI data file of the regarding points of interest (POI) data stored on distance or street name.
Page 139 Navigation of interest stored in the myPOIs ■ Individual POIs: favourite Advantages of POI export and import memory, see "myPOIs announcer" destination addresses that were The export and import of points of below. stored in the myPOIs memory. interest data offer you, e.g., the following advantages: You can export these individual Exporting and importing POI...
Page 140 Navigation Exporting and importing individual For each exported POI category, e.g. POIs and address book entries Restaurant or Private, you will find a correspondingly named file in that Brief description: folder. 1. Connect a USB drive to the USB port of your car's Infotainment Examples: system.
Page 141 Navigation To start the import: press the 3. Store the text files with your POI Each text file name need to consist of CONFIG button, select Navigation data on a USB drive. the category name, a single settings, select Import individual underscore, the category's number 4.
Page 142 Navigation The POI data of each destination address need to be entered in a single separate line, see image above. Storing the text files on a USB drive The text files with POI data need to be stored in a folder named myPOIs that is located in the root directory of the USB drive.
Page 143 Navigation After the import is finished, the Detailed descriptions on POIs stored imported POIs are selectable as in the myPOIs memory, see destinations via the Enter "Exporting and importing POI data" destination menu, see chapter above and chapter "Destination input" "Destination input"...
Page 144 Navigation After selecting the desired option, the list of POI categories is displayed again. If you selected Announce POIs early for a category, the regarding list entry is now set to <On. If you selected Announce POIs late for a category, the regarding list entry is now set to On>.
Page 145 Navigation ■ Address book: selection of a Infotainment system. See destination address stored in the "Selecting a point of interest" address book. See "Selecting an below. address from the address book" ■ Select from map: selection of a below. destination from the map display See also "Storing an address in the using the eight-way switch 3 80.
Page 146 Navigation Description on route guidance, see chapter "Guidance" 3 162. Entering an address directly Press the DEST button and then select Enter address to open the menu shown below. To start a search for petrol stations Below the list detailed information on close to the vehicle's current position: the currently marked petrol station is select Petrol stations.
Page 147 Navigation j : List function - once two letters have been entered (in some cases just one letter), all names available with these letters are displayed. The more letters are entered, the shorter becomes the list. OK : Complete entry or accept search term.
Page 148 Navigation After completing the address, select The Navigation menu is displayed. Starting route guidance Select Start navigation to start route guidance to the displayed address. Description on route guidance, see chapter "Guidance" 3 162. Storing the address Select Store if you want to store the displayed address in the address Select the desired address book A list of the most recently used...
Page 149 Navigation The Store menu is displayed, see Select the desired option. A menu "Storing an address in the address with various sorting options is book or myPOIs memory" below. displayed. Selecting an address stored in the myPOIs memory Press the DEST button and then select myPOIs to open the menu shown below.
Page 150 Navigation Selecting a point of interest Select Automotive & Petrol Stations. Press the DEST button and then A menu is displayed that provides select Points of Interest. options for further refinement of the petrol station search. A menu with various options for the selection of points of interest (e.g.
Page 151 Navigation After marking the desired fuel types: select Start search with selected filters or, for further refinement of the search, select Continue with next filter (petrol station brands/chains). After starting a search, a list of all petrol stations that meet the previously selected filter criteria is displayed.
Page 152 Navigation Along freeway Search by name Selection of motorway related points Selection of points of interest by of interest (e.g. petrol stations or entering a name. service areas) along the route. Only After selecting the option, a country available when you are currently list is displayed.
Page 153 Navigation Once the entry is specific enough, a Description on route guidance, see list with possible points of interest is chapter "Guidance" 3 162. displayed. Sometimes it may be Storing the address necessary to select j to display the Select Store if you want to store the list.
Page 154 Navigation Description on route guidance, see chapter "Guidance" 3 162. Storing the address Select Store if you want to store the displayed address in the address book or myPOIs memory. The Store menu is displayed, see "Storing an address in the address book or myPOIs memory"...
Page 155 Navigation Entering the Longitude coordinate Storing an address in the address or Last destinations), see 1. Select Longitude. regarding descriptions on address address book or myPOIs input or selection above. memory 2. Turn the multifunction knob to select W or E (west or east of the After entering or selecting the desired The Infotainment system provides prime meridian in Greenwich).
Page 156 Navigation A telephone number can be entered Select OK to store the destination Editing or deleting a stored optionally. address in the address book using the address displayed name and category. The default category Private can be Address data (including the category changed to Business: A maximum of 100 destination and telephone number) stored in the...
Page 157 Navigation The following options are available: by simply saying the assigned Editing or deleting Individual POIs name, see chapter "Speech Select Individual POIs, select the ■ Address: opens the Enter address recognition". desired sorting option (e.g. Vicinity menu. You can edit the displayed current position), select the desired address using the speller function, ■...
Page 158 Navigation regarding address book entry or Setting the home address myPOIs entry (selectable via Before you can set an address as Individual POIs). home address, you need to store this address in the address book or ■ Or you can import updated address myPOIs memory, see corresponding data from a USB drive, see descriptions above.
Page 159 Navigation If you want to set the address of an Various options for the selection of Adding a tour imported POI as home address: points of interest based on travel guide criteria (e.g. accommodation, You first need to store the address in sights, leisure etc.) are displayed.
Page 160 Navigation Adding intermediate destinations to Select an option for destination input the tour then select/enter the desired intermediate destination 3 144. A menu is displayed that shows the address data of the selected/entered intermediate destination. Accept the entered name using OK. The name is displayed on the Tours menu.
Page 161 Navigation Starting a tour To start route guidance: select Start tour. All predefined intermediate destinations are taken into account for route calculation. If you want to skip predefined intermediate destinations on the tour and start direct route guidance to a certain destination: select Start tour from.
Page 162 Navigation Guidance Editing a tour To insert the cut out destination at the end of the list: press the multifunction Select a tour in the Tours menu then Press the NAVI button and then the knob again. select Edit tour to display a submenu multifunction knob to display the with the following options: To insert the cut out destination...
Page 163 Navigation ■ Edit: change/edit the displayed Select a TMC traffic message to address, see "Editing or deleting a display detailed information on the stored address" in chapter related traffic issue. "Destination input" above. Navigation options ■ Route criteria: set/change criteria The corresponding menu provides for route calculation, see options and a multitude of relating...
Page 164 Navigation Note For each trip the following data will any time to a USB drive connected to The logbook function of the automatically be recorded: the USB port 3 126 of the Infotainment system meets no Infotainment system. ■ A unique serial number for the trip official legal requirements.
Page 165 Navigation a "1", see "Sample logbook data" ■ Export logbook: exports all Description of the individual data below. recorded trip data currently stored items: in the Infotainment system's ■ Set filename: using the speller ■ 0000000023 = serial number memory to a USB drive connected function (see chapter "Destination ■...
Page 166 Navigation Route criteria The selected settings will be taken Select Dynamic guidance to activate/ into account for route calculation, if deactivate dynamic route guidance. The calculation of the route can be Economic is currently selected, see If dynamic route guidance is controlled by various criteria.
Page 167 Navigation If desired select one or several of the Using the Highway lane guidance If Highway lane guidance is activated following options in the Route option, you can determine which type the following type of illustration will be criteria menu: of illustration should be displayed displayed: when reaching a highway...
Page 168 Navigation Using the Popup information option, Select between map orientation ■ Latitude you can select whether route (North up/Head up) and dimension ■ Longitude guidance information from the (2D/3D) on the map display (3D only ■ Map display navigation should be displayed in available for Navi 900).
Page 169 Navigation Functions for active route Select whether All traffic messages or ■ Destination information only Traffic messages along route guidance ■ Overview current route should be displayed in the TMC Route list messages list, see below. Stop navigation All streets on the calculated route are After selecting Stop navigation, the Navigation options listed with the related distances.
Page 170 Navigation Destination information Route blocking Description, see "Functions with The following options are available to route guidance inactive" above. manually exclude certain areas/route sections from the route guidance: Overview current route The following information on the current route is displayed: To exclude a street from the route guidance: Mark the regarding street name and...
Page 171 Navigation By distance Remove all route blockages Nearby traffic problems are also By setting a distance the section of After selecting this option, all areas/ reported if route guidance is not route from the current position to the route sections previously selected as active.
Page 172 Navigation Dynamic route guidance only works if and roads may differ from those in ■ Do not bend the SD card. Do not traffic information is received via the use at the time the map data was use any SD card that is bent or RDS-TMC traffic information system.
Page 173 Navigation Fold down the panel. Inserting the SD card Removing the SD card Push the SD card with the cut-out edge on the right side (see image Press on the inserted SD card to above) carefully into the SD card slot unlock it, and then carefully pull the until the card engages.
Page 174 Navigation Symbols overview...
Page 175 Navigation Explanation Explanation Current position Closed list Destination Shopping centre not available Toll road not available Tourist information not available Sight Sport & leisure Road works Going out Slippery road Museum Smog Car rental Snow Travel information Storm Leisure activity Caution/warning Provision of services Closed road...
Page 176 Navigation...
Page 177 Navigation Explanation Explanation Chemist Petrol station Cinema Service area Airport Restaurant Amusement park City Historical monument Bank Hospital Traffic message Emergency Ferry Police Border Harbour Tunnel Mountain pass Kiosk Public place Grocery Related to the car Hotel/motel Garage Motorway exit Cemetery Car park Park &...
Page 178 Speech recognition Speech recognition General information from this, the speech recognition acknowledges important commands The speech recognition of the and will enquire if necessary. Infotainment system enables you to To ensure that conversations inside operate various functions of the General information ....178 the vehicle do not lead to navigation system (only Navi 900;...
Page 179: Navigation Control
Speech recognition To be able to enter voice Note most important commands currently commands in English, you first If you change the language shown available is shown on the display, see need to activate the phone main on the Infotainment system's "Help menus"...
Page 180 Speech recognition Cancelling a dialogue sequence Afterwards, the current dialogue Help menus sequence will be continued Dependent on the currently active There are various possibilities to automatically. mode of operation (radio, CD player, deactivate the speech recognition navigation etc.), a help menu with the and to cancel a dialogue sequence: Important notes on voice input most important available voice...
Page 181 Speech recognition ■ One of the commands shown on Example: General help menu (main You can simply try out if there are the help menu. commands) shortened variants available for The general help menu primarily certain commands. ■ One of the additional commands shows the commands required to available for the radio mode, see ■...
Page 182 Speech recognition <87.5..108.0>", you need to Example: Autostore lists On-screen messages and acoustic exchange "<87.5..108.0>" for a prompts / feedback specific figure between 87.5 and During dialogue sequences you are 108.0. You could say, e.g., often prompted via on-screen "Frequency 96 dot 3". messages (see image below) and voice output messages, which kind of Help messages...
Page 183 Speech recognition As soon as you hear a beep and the System: "Radio". Selecting a preset station symbol in the upper right corner of the Action: the user wants to select a System: activates the radio mode. on-screen message (see image station stored in the second autostore To perform a certain radio function via above) has changed its colour from...
Page 184 Speech recognition After assigning a name to a station, Selecting a preset station via the Selecting a track on an audio CD you can select that station by simply assigned name User: activates speech recognition. saying the assigned name. User: "All tracks". Note Action: the user wants to assign a If you use a name which was...
Page 185 Speech recognition User: "Points of interest". Entering an address Action: user wants to enter the System: shows a list with search destination address for an upcoming options. trip. User: "Nearby". User: activates speech recognition. System: shows a list with points of User: "Enter destination"...
Page 186 Speech recognition Note System: displays an alphabetically destination" to store the displayed The last calculated destination ordered list of street names that address in the address book or possibly has no valid address sound similar to the name the user myPOIs memory, see chapter elements available that can be used said.
Page 187 Speech recognition Example: the language of the Afterwards you can select one of Note Infotainment system is set to English, these destination addresses by If you change the language shown Country is set to "GERMANY (D)", simply saying the assigned name. on the Infotainment system's and you want to enter the city name display, all names currently...
Page 188 Speech recognition Infotainment system (e.g. the RADIO ■ Do not enter (say) any commands ■ "Delete" button) or the SRC (Source) button on for some time. ■ "Directory" the steering wheel. ■ After the third unrecognised ■ "Pair" command. ■ "Select device" Phone control Operation ■...
Page 189 Speech recognition Recognition works best, if a pause of without knowing the prefix for calls ■ "Help" at least half a second is made after made abroad in that country. Then ■ "Cancel" every three to five digits. The say the required country code. Example of a dialogue Infotainment system then repeats the Example of a dialogue...
Page 190 Speech recognition ■ "Redialing" both name inputs, otherwise the Voice output: "Please, say the speech recognition will reject the number to save" ■ "Help" inputs. (for number input see the dialogue ■ "Cancel" A maximum of 50 voice tags can be example for Entering a telephone Example of a dialogue stored in the telephone book.
Page 191 Speech recognition Listening to stored names Voice output: "Do you want to add or User: "Yes" delete a device?" The voice output of all stored names Voice output: "Do you want to pair the (voice tags) is started with the User: "Add"...
Page 192 Phone Phone General information Important information for operation and traffic safety The Phone portal provides you with the possibility of having mobile phone 9 Warning conversations via a vehicle General information ....192 microphone and the vehicle Mobile phones have effects on Bluetooth connection ....
Page 193 Phone Controls on steering wheel: Navi 600 / Navi 900 phones is prohibited, if q, w: take call, activate speech interference is caused by the Bluetooth menu recognition. mobile phone or if dangerous situations can occur. n, x: end/reject call, deactivate speech recognition.
Page 194 Phone Device list Handsfree mode Connecting a mobile phone as a When the mobile phone is added as handsfree device When a mobile phone is connected to a handsfree device the user can the Phone portal via Bluetooth for the make or receive calls and use other first time, the mobile phone is saved functions via the Phone portal.
Page 195 Phone As soon as the Phone portal has Select Change Bluetooth code. On Select the desired mobile phone from detected the mobile phone, the the menu displayed, edit the actual the list. The SAP passcode prompt is connection set-up can be confirmed. Bluetooth code and accept the shown on the Infotainment display modified code using OK.
Page 196 Phone Enter the displayed SAP passcode in Connecting a mobile phone saved in Removing a mobile phone from the the mobile phone (without spaces). the device list device list The mobile phone PIN code is shown Select the desired mobile phone from on the Infotainment display.
Page 197 Phone The security dialogue is displayed. ■ Call diverting: select diverting CD 300 / CD 400plus options depending on the situation. Activating/Deactivating PIN request Bluetooth menu ■ Call barring: configure call barring Select PIN request On or Off. options depending on the situation. Enter the PIN code of the mobile For details on network services phone SIM card and confirm.
Page 198 Phone Device list Handsfree mode Connecting a mobile phone as a When a mobile phone is connected to When the mobile phone is added as handsfree device the Phone portal via Bluetooth for the a handsfree device the user can first time, the mobile phone is stored make or receive calls and use other in the device list.
Page 199 Phone As soon as the Phone portal has Select Change Bluetooth code. On Select the desired mobile phone from detected the mobile phone, the the menu displayed, edit the actual the list. The SAP passcode prompt is connection set-up can be confirmed. Bluetooth code and accept the shown on the Infotainment display modified code using OK.
Page 200 Phone Enter the displayed SAP passcode in Connecting a mobile phone saved in Removing mobile phone from device the mobile phone (without spaces). the device list list The mobile phone PIN code is shown Select the desired mobile phone from on the Infotainment display.
Page 201 Phone Emergency call The security dialogue is displayed. ■ Call diverting: select diverting options depending on the situation. Activating/Deactivating PIN request ■ Call barring: configure call barring 9 Warning Select PIN request On or Off. options depending on the situation. Enter the PIN code of the mobile Connection setup cannot be For details on network services...
Page 202: Introduction
Phone Operation the mobile phone is possible via the functions are active. You can Infotainment system only to a limited enquire about this with the local extent. Introduction network operators. Not every telephone supports all As soon as a connection via The emergency call number can functions of the Phone portal.
Page 203 Phone Dialling a telephone number Entering a number manually If the SIM card or telephone are different, the telephone book is reloaded. This process can take a few minutes depending on the phone model. Selecting a telephone number from the telephone book With the telephone main menu active, Select Enter number, then enter the press the multifunction knob to open...
Page 204 Phone Call lists Messaging functions Note Telephone book entries are carried Via the menu Call lists the incoming, When the mobile phone is paired over as they are transferred from the outgoing and missed calls can be using the SAP mode, messages can mobile phone.
Page 205 Phone Incoming call ■ Switch calls: switch between calls, Dialling a telephone number if there are several calls. When there is an incoming call a menu is displayed for you to accept or ■ Mute call: mute a call. decline the telephone call. Note Select the required option.
Page 206 Phone Entering a number manually If the SIM card or telephone are different, the telephone book is reloaded. This process can take a few minutes depending on the phone model. Selecting a telephone number from the telephone book Note Telephone book entries are carried Select Enter number and then enter over as they are transferred from the the desired number sequence.
Page 207 Phone Call lists Incoming call When there is an incoming call a menu is displayed to accept or decline the telephone call. Select required option. Functions during a telephone call If you currently have a telephone call, press the multifunction knob to open a submenu.
Page 208 Phone ■ Switch calls: switch between calls, Recommendations for fault-free For reasons of safety, do not use the if there are several calls. operation: phone while driving. Even use of a handsfree set can be a distraction ■ Mute call: mute a call. ■...
Page 209 Phone...
Page 210 Index Activating CD player....120 Emergency call......201 Activating speech recognition..Enhanced Other Networks..111 ........179, 188 EON..........111 Activating the navigation system 134 Activating the radio..... 102 Favourite lists......104 Address book......144 Address input......144 Autostore lists......103 General information....
Page 211: Repeat Last Navigation Message
volume of the traffic importing/exporting POIs..134 announcements......98 Logbook........162 Personalisation......100 volume settings......98 map SD card......172 Phone myPOIs........144 adjusting ring tones....193 myPOIs announcement..134 Bluetooth......... 192 Maps .......... 172 navigation display....134 Bluetooth connection....193 Map SD card navigation options....
Page 212 selecting the waveband..102 Storing stations....103, 104 station lists......106 Switching the Infotainment station search......102 system on or off......89 usage........102 Switching the radio on....102 waveband menus....106 Symbols overview ...... 174 Radio data system (RDS) ..111 RDS..........
Page 213 Copyright by ADAM OPEL AG, Rüsselsheim, Germany. The information contained in this publication is effective as of the date indicated below. Adam Opel AG reserves the right to make changes to the technical specifications, features and design of the vehicles relative to the information in this publication as well as changes to the publication itself.

This manual is also suitable for:

Navi 650 Navi 900 Navi 600 Cd 400plus Cd 400 Cd 300 ... Show all

ADAM OPEL Navi 950 Manual

Navi 950/650 / CD 600

Introduction

Basic Operation Basic Operation

24 Radio Radio Usage

Quick Links

Chapters

Need help?

Questions and answers

Summary of Contents for ADAM OPEL Navi 950

This manual is also suitable for:

Table of Contents