Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Elium IRD 1080
-
Page 1: Operating Instructions
Operating Instructions 19“ DVB SD/HD IRD Integrated Receiver Decoder... - Page 2 We thank you for your confidence in our product and congratulate you to the purchase of your Digital Receiver of ELIUM GmbH. As this product is provided with an immense array of features, we recommend you to review the contents of this manual before proceeding.
-
Page 3: Table Of Contents
Table of contents 1. Information Accessories ....3 Safety Regulations ... . . 4 Remote Control ....5 2. -
Page 4: Information
Information 1.1 Accessories ▪ Digital SD/HD IRD Integrated Receiver Decoder ▪ Remote Control / Batteries (optional) ▪ Operating Instructions (Service CD) -
Page 5: Safety Regulations
Information 1.2 Safety Regulations Pay attention to the following before using this unit. To be sure read these instructions carefully and use the set prop- erly. Be sure to keep this manual for future reference, should any question or problem arise. Power Cord Handle the power cord carefully. -
Page 6: Remote Control
Information 1.3 Remote Control The remote control enables the interaction with the HCR receiver. Therefore it is very important to know about the main functionality. 1 - On / Off (StandBy) 2 - Channel selection or data input 3 - Switch between TV and radio mode 4 - Not active 5 - RCL return to last channel 6 - Mute... -
Page 7: Installation
Installation 2.1 OSD Settings After switching on the SD/HD IRD with the StandBy button (1) of the remote control you should see a welcome screen on the TV set. Now you can start setting up the OSD (On Screen Display) settings. How to set up the OSD: ▪... -
Page 8: Video Settings
Installation 2.2 Video Settings After setting the OSD you may set up the video settings. How to set up the video functions: ▪ To move between the different options press the up or down button (7). ▪ To select a setting press the OK button (10). ▪... -
Page 9: Audio Settings
Installation 2.3 Audio Settings After setting the video settings you may set up the audio settings. How to set up the audio configuration: ▪ To move between the different options press the up or down button (7). ▪ To select a setting press the OK button (10). ▪... -
Page 10: Antenna Settings Only Dvb-S
Installation 2.3 Audio Settings HDMI AUDIO In HDMI you can switch between Audio 1 (Analog L-R) and Audio 2 ( Digital / AC3 ). ▪ To save the adjustment of the sound settings press the exit button (9). ▪ To leave the sound settings press the exit button (9) again. -
Page 11: Search For Channels / Programs
Installation 2.4 Antenna Setting DVB-S Setting up the antenna. Depending of the receiving part of your SD / HD IRD vary the settings of the channel search. The SD/HD IRD is preset for astra satellite. But you can set up the antenna installation as well as the channel search for other satellites. -
Page 12: Channel Search
Installation 2.5 Channel search How to do a channel search. Depending on the reception option of the unit, you have different options shown for the channel search. In this menu the signal strength and quality is indicated. To change the frequency press the left or right button (8). There are two options and additional option for the channel search: ▪... -
Page 13: Edit Channels
Channels 2.6 Edit Channels After the channel search you can edit the found channels. You can select to edit TV channels or Radio channels. Also you can edit the volume of each channel separately. The description is for both TV and Radio list. ▪... -
Page 14: Technical
Technical 3.1 Technical Menu The Technical Menu shows you different information. Here you can set up technical information regarding the unit such as date and time. There are different options shown in this menu: ▪ Box Info: Shows you technical information of the unit like the current firmware. -
Page 15: Network Settings
Technical 3.2 IP Settings Available settings: Optional you can select between one or two Ethernet ports. ( Regulated by your SD/HD IRD ) Ethernet 1 = Streaming and control Ethernet 2 = Control The IP addresses of the Ethernet 1 and Ethernet 2 have to be in different IP areas. -
Page 16: Menu Via Display
Technical 3.3 Menu via Display It is possible to change the settings via the front panel. By pressing the „M“ button the following menu structure appears in the display: OSD Language Choose the OSD Language OSD Transparency Choose the transparency on menu OSD Colours Set the OSD colours OSD Background... - Page 17 Technical 3.3 Menu via Display Technical Menu Box Info Readout software, hardware version and more ... Stream Info Readout transponder, picture format, ... Control Startup functions Fan Settings Fan settings eSATA Settings for the hard drive / format hard drive Time Zone Set time zone Access Module...
-
Page 18: Phone Support
Technical 3.4 External Boxeditor / Telefonsupport External Channellisteditor - BOXEDIT ▪ Connect your PC and the receiver via a RS232 cable. ▪ Start the Boxedit. Following functions are available: ▪ Load from Box: Loads TV and Radio channel list to the PC and displays it. ▪... -
Page 19: Esata
Technical 3.5 eSATA Important: The connected hard drive have to be formatted to the right format by the device: Menu/ Technical Menu/ eSATA/ Interface 1/ Format HDD Interface 2/ Format HDD Make sure the cables are correct connected. ( eSATA 1 = Bottom interface on device ) ( eSATA 2 = Top interface on device) In the eSATA menu you can change the sleep time and the running noise of the hard drive. - Page 20 Technisches 3.5 eSata With the PVR button „15“ you get into the movie menu: The movieNET menu allow to play movies from the hard drive. ▪ With the “stop” button „21“ you start a selected movie. ▪ With the buttons rewind „16“ fast forward „17“ you can rewind or fast forward a movie. ▪ With the Play / Pause button „18“...
-
Page 21: Additional Functions
Technical 3.6 Additional Function In the following some diverse function of the unit are listed which you can select using the Remote Control. ▪ TV - Radio button (3): Using this button you can switch between TV Channels and Radio Channels. ▪... -
Page 22: Network Access
Technical 3.7 Network Access Connect the device with your computer or network. Make sure the device communicates with your computer. To play videos, audios, images or recordings from your computer you have to create a folder on computer and share it to your network (for example “media” in image 1). To detect the videos, audios, images or recordings you have to create folder for them. -
Page 23: Livestreaming => Network
Technical 3.8 Live Streaming => Network ( Streaming Server ) Connect the device with your computer or network. Make sure the device communicates with your computer. Important: The IP addresses have to be in the same network address. For live streaming the HDR / IRD-HD Decoder have to be connected with a network cable. HDR / IRD-HD Decoder settings for broadcast: Then activate the Stream to Network option in the menu of HDR or IRD-HD Decoder (Image 1 and 2). - Page 24 Technisches 3.8 Live Streaming => Network The default port for RTP and UDP protocol is 1234, this port have to be the same as in the VLC Player. The HTTP protocol uses the 31339 port. Please take care the ports are not in use. VLC Player Einstellungen: Open VLC Player.
- Page 25 Technisches 3.8 Live Streaming => Network For a HTTP protocol variant 3: Network address for a HTTP Stream: „http://10.1.1.65:31339/ watch?tv=1“ Switch single programs. Back to program list with the stop button of the VLC player. Image 7 In the VLC menu bar, Playback ---> Program.., you can switch between the programs of the streamed transponder (Image 8).
-
Page 26: Livestreaming <= Network
Technical 3.9 Live Streaming <= Network ( Streaming Client ) Connect the device with your computer or network. Make sure the device communicates with your computer. HDR / IRD-HD Settings: The settings you find in: Menu -> Channelsearch -> Network Protocol: rtp or udp (raw) Multicast:... -
Page 27: Information Window
Technisches 4.0 Information-Window With the <EXTMSG msg> command you can display a permanent message. With the <EXTPOPUP msg> command you can display a temporary message. -
Page 28: Update
FAT 32 format. NOTE: Only FAT 32 formatted usb drives are suitable for the update. Current firmware updates can be found in ELIUM website: http://www.elium.de/files/download/elium_ird_update.zip http://www.elium.de/files/download/IRD_RS232_Protocol.pdf http://www.elium.de/files/download/Boxedit.exe 1. Save the selected firmware update to your USB drive. - Page 29 Technical 4.1 Update 3. When update completes „Flashing ... OK“ prompt appears on LCD and you can remove the usb drive from receiver. Restart the device by turn the device off and on again. For reboot, please push OK 4. Please confirm the reboot by pushing the OK button once, after it´s prompted on LCD.
Need help?
Do you have a question about the IRD 1080 and is the answer not in the manual?
Questions and answers