Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PET Bigfoot
Summary of Contents for PET Bigfoot
-
Page 2: Table Of Contents
Table of Contents Technical Information-----------------------------------1 Warning Statement--------------------------------------2 Read Before Riding-------------------------------------3 List Of Parts-----------------------------------------------4 Front Bar---------------------------------------------------6 Tool Kits In The Tool Bag------------------------------7 Assembling The Bigfoot-------------------------------8 Charging The Batteries--------------------------------9 Using The Alarm----------------------------------------10 Riding The Bigfoot -------------------------------------12 Maintenance---------------------------------------------14 Wiring Diagram-----------------------------------------15 Trouble Shooting Guide------------------------------17 Warranty--------------------------------------------------19... -
Page 3: Technical Information
Bigfoot Model No. PET Bigfoot 67.7 L x 41 W x 32.7 H inch Product size (172 L x 105 W x 83 H cm) Type of motor DC brushless motor Motor power 60 V 1000W Battery type Li battery... -
Page 4: Warning Statement
Bigfoot... -
Page 5: Read Before Riding
Bigfoot... -
Page 6: List Of Parts
Bigfoot... - Page 7 Bigfoot Throttle Multi-function Instrument Brake lever Seat Frame Rear fender Brake lamp Rear brake assembly Motor Rear brake plate Rear tire Battery Front fork Front brake assembly Front tire Front fender...
-
Page 8: Front Bar
Bigfoot 1 Rear brake lever 2 Horn switch 3 Multi-function Instrument 4 Key switch 5 Front brake lever 6 Throttle... -
Page 9: Tool Kits In The Tool Bag
Bigfoot Screwdriver Allen wrench （8mm） Wrench (12 x 14mm) Charger... -
Page 10: Assembling The Bigfoot
1. Unpack the PET Bigfoot carefully so that you do not misplace any of the parts. 2. Place the PET Bigfoot on a flat level surface. Remove the bolts in the front stem. Place the handle bar(A) into the front stem(B). After aligning the holes, place the bolt through the handle bar assembly. -
Page 11: Charging The Batteries
Bigfoot Before you ride the PET Bigfoot for the first time ● you must charge the batteries for 5-6 hours using only the supplied charger. To charge the batteries, plug the charger into ● the charger socket located on the side of the battery/ controller compartment. -
Page 12: Using The Alarm
Bigfoot 1. “1” is the Alarm Button. when shutting off the main key, pressing one time gently, the horn will ring one loud, the scooter will be on alert. When touching the scooter or driving the scooter, the horn will ring 15 seconds. If forcing to move the scooter, the horn will ring continuously. - Page 13 Bigfoot one time gently, the horn will ring five seconds and alerts us the scooter’s location. When the power is shut down, pressing “4” ● button until horn rings. Ringing one loud stands for sensitivity level 1(highest), ringing two loud stands for sensitivity level 2……...
-
Page 14: Riding The Bigfoot
Once you have completed the initial charge you ● are ready to ride. Remember, this is not a toy. The PET can reach speeds up to 22.8 mph depending on the terrain and the weight of the rider. You must wear a helmet and protective pads. - Page 15 Bigfoot hand will control the throttle and front brakes. As you turn the throttle towards yourself, the speed will be increased. Release the throttle and apply the brake to stop the scooter. You will control the speed of the scooter by using both the throttle and the brake.
-
Page 16: Maintenance
To prolong battery life, recharge the battery after each use. You must also charge your PET if it has not been used for 30 days. If you need to replace the battery pack, it is located inside the battery compartment on the footboard. -
Page 17: Wiring Diagram
Bigfoot... - Page 18 Bigfoot...
-
Page 19: Trouble Shooting Guide
3. Replace throttle. Call Customer Service to order a new throttle. Power is on, 1. The battery 1. Repair again. but PET Bigfoot connection 2. Replace throttle. still does not loose. Call Customer work. 2. The throttle is Service to order a destroyed. - Page 20 Bigfoot The charger 1. The charger 1. Fasten the plug. does not work. plug fall off or 2. Replace the fuse. plug and socket 3. Weld the battery connection connection lines well. loose. 2. The fuse burnout. 3. The battery connection lines fall off.
-
Page 21: Warranty
Any part of the PET product manufactured or supplied by PET and found in the reasonable judgment of PET to be defective in material or workmanship will be repaired or replaced by an authorized PET service dealer without charge for parts or labor. - Page 22 Bigfoot cancellation or rescission of the contract of sale of any PET product. Proof of date of purchase will be required by the dealer to substantiate any warranty claim. An authorized PET service dealer must perform all warranty work. The...
- Page 23 PET’s obligation under this warranty is strictly and exclusively limited to the repair and replacement of defective parts and PET does not assume any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
- Page 24 PET Customer Service - warranty repair Tel. 1-707-521-9257 www.petscooters.com DO NOT RETURN YOUR PRODUCT TO ANY ADDRESS. Please call or write for the location of the PET authorized service center nearest you and for the procedures for obtaining warranty claims.