Page 1
GSM/GPRS/GPS TRACKER USER MANUAL Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release.
1 Summary Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS. 2 Main functions · GSM quad-band frequency; · Real time tracking by SMS/GPRS; · Recover original password; ·...
4. SIM card installation 4.1 Preparation Please insert SIM card before turning the device power switch to on; The SIM card need open the GPRS function; Please make sure SIM card with full balance. 4.2 Device light description Color Represents power yellow GSM signal...
5.2 Device wiring diagram 6. Device Parameter Settings 6.1 Initialization Send SMS “#begin#” to the tracker, it will reply “begin ok” and initialize all the settings. (Default password: 123456). Remark: initialization is resetting all the parameters to factory defaults. For example, send SMS “#begin#”, If succeeded, it will reply“begin ok”. 6.2 Set password 6.2.1Set Password:...
For Example, send SMS: “#password#123456#666888#” to device, it will reply SMS: “password OK”. 6.2.2 Make sure the new password is in 6 digits arabic numbers, or the device cannot recognize the password. 6.2.3 Resume original password: send SMS: “#resume#” to the device, it will reply SMS: “resume password, password is 123456”.
Note: when GPS signal is weak, you will receive the last location when GPS is available. If it is different with its exact current location, pay attention to check the time included in the SMS. 6.5 Get geographical location 6.5.1 Must set the SIM Card APN parameter firstly before using this function, if there is APN user name and password, Please refer to point 6.13 to set.
6.6.3 Cancellation: Send SMS “#noat#password#” to the device. 6.7 Voice Surveillance & Two-way calling It need connect external microphone, two-way calling function is optional. 6.7.1 Device has 3 mode to switch, the default mode is “tracker” mode (Tracking status). 6.7.2. Send SMS “#monitor#password#” to the device, and it will reply “monitor ok!”...
“#stockade#password#semidiameter#” to unit to set the restricted district. For example, send SMS: “#stockade#123456#3#”, “3” represents 300 meters. In case of breach, it will send SMS “stockade!+Geo-info” to the authorized number. 6.8.2 Cancel: Send SMS: “#nostockade#password#” to deactivate this function, it will reply “no stockade ok”. 6.9 Overspeed alarm 6.9.1 Set up: Send SMS:“#speed#password#speed number in 3 digits#”...
6.11 SOS alarm When connect external SOS wire, if press the SOS button, device will reply "SOS alarm! +IMEI number+Long&Lat" to authorized number. 6.12 Time Zone Setting Remark: UTC+8 is default time zone. 6.12.1 Send SMS “#timezone#password#direction#time zone value in hours#time zone in munites#”.
Send SMS “#supplyelec#password#” to device, it will reply “supply electricity ok”, recover circuit successfully. 6.15 Power failure alarm Built-in backup battery to send SMS “cut power alert! +IMEI number+Long&Lat” to the authorized number when the power was cut. 6.16 Check device setting parameters Send SMS “TCP”...
Notes: CMNET is the APN content of China Mobile (it has no APN user name and password). 6.17.2 IP and Port setting Send SMS “#IP#password#ip address#port number#”. If succeeded, “set ip address and port ok” will be returned by SMS. E.g, Send SMS command “#IP# password #58.64.200.27#6780#”...