Download Print this page

LG 4300 Instructions

Dual-handed swingbolt or deadbolt electronic lock.
Hide thumbs
   

Advertisement

Lock Choices
4300
Dual-Handed Swingbolt
4300 is a new part
number replacing the
6260
STANDARD FEATURES
MANAGER CODE (Factory set to 1-2-3-4-5-6 or 7-8-9
depending on code length)
CODE LENGTH
• Activate/Delete Users
• Enable/Disable Users
• Set Time Delay Values
• Open Lock
USER CODE
• Open Lock
• Change Code
TIME DELAY
• Delay period 1 - 99 minutes
• Open period 1 - 19 minutes
DUAL CODE
• Two codes required to open
SIGNAL TO DISABLE LOCK OPENING
Required)
• Input signal disables opening of lock by valid code
WRONG TRY PENALTY
• Four (4) consecutive invalid codes initiates five minute
delay period.
LOW BATTERY WARNING
• Repeated audio and visual signal (LED flashing and
repeated beeping) during opening indicates battery low.
AUDIO AND VISUAL SIGNAL
• Double signal (LED flashes and unit beeps) indicates
entry is valid or accepted.
• Triple signal indicates invalid or not accepted.
AUDIT TRAIL
• For audit features see LPAUDIT Software Package
PC PROGRAMMABLE FEATURES
MULTIPLE USERS
Up to nine (1 Manager and 8 Users)
User # Installed 2
3
4
TIME DELAY OVERRIDE
• Ability to add second combination to override delay
period
SILENT SIGNAL ALARM
(Optional Alarm Box Required)
• Duress signal if last number of code(s) is entered using
one number higher or one number lower.
SIGNAL TO DISABLE LOCK
• Input signal disables all lock functions by valid code
e KEY II
e KEY or
• Use of key and code required
© copyright 2006
4300 Dual-Handed Swingbolt or 6040-DB Deadbolt Lock Instructions
MANAGER PROGRAMMING
Suggested Keypad
6040-DB
Deadbolt
3750-K
Round Entry
(Optional Alarm Box
5
6
7
8
9
(Optional Alarm Box Required)
12-239v3
All locks are shipped from the factory in Pre Set-up
mode, with no features installed.
Lock will open when 1 is pressed.
Please follow LPAUDIT PC software instructions to
initially configure locks to default settings.
OPENING THE LOCK (Without e KEY or e KEY II )
1 Enter valid six (6) digit code.
2 The unit will indicate a valid code entry with a double signal.
3 Within four (4) seconds open lock by either rotating the keypad
3125 Round
to open position (Clock-wise) or turning the handle to the open
Entry
position.
4 Pull door open.
ACTIVE
• Invalid Code Entry - Unit will signal three (3) times.
CHANGING YOUR CODE (Without e KEY or e KEY II )
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
If your unit is programmed for Dual Code, each code must be
changed independently.
1 Enter existing code and hold down the last digit until unit
double signals twice and the LED stays on.
2 Press the "0" key.
3 Enter your NEW six (6) digit code two times.
m If a mistake is made wait thirty (30) seconds and repeat steps 1
- 3.
4 Test unit operation several times before closing the door.
• Valid Code Entry - Double signal after valid six (6) digit code is
entered.
• Invalid Code Entry - Triple signal and old code is still valid.
MANAGER CODE MUST BE CHANGED PRIOR TO
PERFORMING ANY ACTION OTHER THAN OPENING THE
LOCK
ACTIVATING USER (Manager Only, without e KEY or e KEY II )
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1 Enter Manager code and hold down last digit of code until unit
double signals twice and the LED stays on.
2 PRESS 1. Unit signals twice.
3 Press User number, 2 to 9. Unit signals twice.
4 Enter NEW six (6) digit User code two times.
5 If a mistake is made wait thirty (30) seconds and repeat steps
1 - 4.
• Valid Code Entry - Double signal after valid six (6) digit code is
entered.
• Invalid Code Entry - Triple signal and old code is still valid.
DISABLE USER (Manager Only, without e KEY or e KEY II )
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1 Enter Manager code and hold down last digit of code until unit
double signals twice and the LED stays on.
2 PRESS 2. Unit signals twice.
3 Press User number, 2 to 9. Unit signals once.
4 User is temporarily disabled.
5 If a mistake is made wait thirty (30) seconds and repeat steps
1 - 3.
• Valid Code Entry - Double signal after valid six (6) digit code is
entered.
• Invalid Code Entry - Triple signal and old code is still valid.
LA GARD INC - A Member of The Kaba Group

Advertisement

   Related Manuals for LG 4300

   Summary of Contents for LG 4300

  • Page 1

    4300 Dual-Handed Swingbolt or 6040-DB Deadbolt Lock Instructions MANAGER PROGRAMMING Lock Choices Suggested Keypad All locks are shipped from the factory in Pre Set-up • mode, with no features installed. Lock will open when 1 is pressed. • 6040-DB Please follow LPAUDIT PC software instructions to •...

  • Page 2

    e KEY II ) REINSTATE USER e KEY or (Manager Only, without ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN 1 Enter Manager code and hold down last digit of code until unit double signals twice and the LED stays on. 2 PRESS 1.

  • Page 3

    KEY II ) OPENING THE LOCK (With e KEY or e 1 Enter valid six (6) digit code and insert key. 2 The unit will indicate a valid code and key entry with a double signal. 3 Within four (4) seconds open lock by either rotating the keypad to open position (Clock-wise) or turning the handle to the open position.

  • Page 4

    LOCKS USING THE KEY FEATURE MUST BE ORDERED THAT WAY FROM THE FACTORY. PLEASE SEE PRICE LIST FOR KEY II USE . PART NUMBERS FOR LOCKS SET-UP FOR e KEY or e KEY II ) SET/CHANGE TIME DELAY VALUES (Manager Only, with e KEY or e 1 Enter Manager code and hold in key until unit double signals twice and the LED stays on.

This manual also for:

6040-db

Comments to this Manuals

Symbols: 0
Latest comments: