Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for CNC 6040z-s65j
- Page 2 Congratulations! You already have your own numerical control engraving machine, but you need to carefully know it and master it, in order to make it your good assistant as soon as possible. Before installing and using this machine, you must read carefully about this manual. Please properly preserve this manual for reference in the future.
- Page 3 ②Design the content that needs to be engraved through design software, and output G code or nc, Tab files that can be recognized by Mach3; ③Firmly clamp the materials need to be engraved on the operating platform of engraving machine; ④Import engraving code to the control software Mach3, send out command to the engraving machine after passing through the code, and then the engraving machine will start to operate.
- Page 4 6040Z+S80 CNC Engraving Machine CONTENTS ■Read Read Read before before using using Read before before using using----------------------------------------------------------------1 ■T T T T o o o o know know know know your your your your engraving engraving engraving engraving machine machine machine machine------------------------------------------4 ·Composition name of the machine...
- Page 5 ■To know your engraving machine ◆Composition name of the machine ◆Sketch Sketch Sketch map of of of of installation installation installation wiring wiring Sketch map installation and and wiring wiring...
- Page 6 ■T T T T o o o o test test test your your engraving engraving machine machine test your your engraving engraving machine machine ◆Installing the control software ·Software is not included in this machine, so please purchase appropriate software in line with your fondness;...
- Page 7 ③ ④ ⑤...
- Page 8 Please Please carefully carefully read read above above picture picture setup, setup, mistake mistake mistake of of of of any number number number or or or or option option option Please Please carefully carefully read read the the above above picture picture for for setup, setup, and...
- Page 9 ◆Definition of triaxial coordinate The following is the reference drawing of the triaxial coordinate definition provided by us. During the process of trial run, if we found the running direction of the axis is incorrect, we can change the "Dir LowActive"...
- Page 10 If the test shows that water pump and spindle motor are normal, you may begin go engrave. ■Attention: you must first start the water pump before starting the spindle motor at any time, to ensure that the cooling water circulation is normal. Otherwise, the rotation speed of 24000 cycles may let the spindle motor generate extremely high temperature within short time, and let it be burned.
- Page 11 ■To To To To use your your engraving engraving machine machine use your your engraving engraving machine machine ◆Primary engraving practice: Engraving of graphic pictures and texts Let's do the primary engraving practice by taking the right picture as an example. This is a simple graphic engraving of pictures and texts, and it is also the main purpose of engraving machine.
- Page 12 ①First, we operate the XY axis through manual control, and move the principal axis close to the initial point; Install a flat base pointed knife. ②Turn off the power switch of electric cabinet (the phase step motor will not be self-locked when the stepping motor power is cut off), and then slowly wring the hand wheels for fine control on three , to...
- Page 13 ①leave certain margin when clamping materials, so as to avoid the cutter from touching screws; ②remember to reset the triaxial coordinates after tool setting; ③remember to adjust the speed adjustment button of the principal axis to the zero position in anticlockwise direction.
- Page 14 ◆Secondary engraving practice Now, we can use the auxiliary operating platform. Double color plate is one of the most commonly used engraving materials, which is shown as the following picture: ①Stick double-faced adhesive tape on the back of the double color plate; ②Paste it on the milled plane of the auxiliary operating platform, and press it to make it stickfast;...
- Page 15 a tool, and if you want it to play a more important role and engrave better objects, you must have the ability to "send command" to it. The command that can be executed by the engraving machine is called "processing code", and in order to produce these "processing codes", you have to learn some software.