1. Manuals
  2. Brands
  3. Kaz Manuals
  4. Fan
  5. HY-254 SeriesHY-280 Series
  6. Owner's manual

Kaz HY-254 SeriesHY-280 Series Owner's Manual

Hy-254 series hy-280 series tower fans
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Table of Contents

Owner's Manual
IMPORTANT SAFETY
INSTRUCTIONS
READ AND SAVE THESE SAFETY
INSTRUCTIONS BEFORE USING
THIS FAN
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
FOR US MODELS ONLY – This product
employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product
from the outlet. Replace the fuse as per the
user servicing instructions (follow product
marking for proper fuse rating) and check
the product. If the replacement fuse blows,
a short-circuit may be present and the
product should be discarded or returned to an
authorized service facility for examination and/
or repair.
1.
Use this fan only as described in this
manual. Other use not recommended as
it may cause fire, electric shock or injury
to persons.
2.
This product is intended for household
use ONLY and not for commercial,
industrial or outdoor use.
3.
To protect against electric shock, do not
place fan in window, immerse unit, plug
or cord in water or spray with liquids.
QUIETSET
®
WHOLE ROOM TOWER FAN
HY-254 Series
HY-280 Series
4.
This appliance has a polarized plug
(one blade is wider than the other). To
reduce the risk of shock, this plug is
intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety
feature.
5.
Close supervision is necessary when any
appliance is used by or near children.
6.
Turn the fan OFF and unplug the fan from
the outlet when not in use, when moving
the fan from one location to another and
before cleaning.
7.
To disconnect the fan, first turn the unit
OFF, grip the plug and pull it from the wall
outlet. Never pull the plug by the cord.
8.
Do not operate the fan in the presence of
explosive and/or flammable fumes.
9.
Do not place the fan or any parts near
an open flame, cooking or other heating
appliance.
10. Do not operate the fan with a
damaged cord or plug or if the product
malfunctions, is dropped
or damaged in any manner
(see warranty).
11. Avoid contact with moving fan parts.
12. The use of attachments not
recommended by the manufacturer may
be hazardous.
13. Place the fan on a dry level surface.
14. Do not hang or mount fan on a wall
or ceiling.
15. Do not operate if the fan housing is
damaged.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HY-254 SeriesHY-280 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Kaz HY-254 SeriesHY-280 Series

Summary of Contents for Kaz HY-254 SeriesHY-280 Series

  • Page 1 Owner’s Manual QUIETSET ® WHOLE ROOM TOWER FAN HY-254 Series HY-280 Series IMPORTANT SAFETY This appliance has a polarized plug (one blade is wider than the other). To INSTRUCTIONS reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet.
  • Page 2 Electric Shock, Do Not Use This Fan With fan was purchased, or request a return Any Solid-State Speed Control Device, authorization to return to Kaz USA, Inc. for other than the one supplied. examination and/or repair. FUSED SAFETY PLUG - FOR US ONLY Thank you for your purchase.
  • Page 3 ASSEMBLY INSTRUCTIONS A. Pedestal Assembly Fig. 1 • L ine up the left and right pedestal assembly and firmly snap together (Fig. 1). B. Base Assembly • A lign the two portions of the circular base and snap together by gently pushing the 4 extrusions (Fig. 2, Item A) into the adjacent Pedestal Assembly circles of the connecting piece (Fig. 2, Item B). Fig. 2 C. Securing the Pedestal to the Base Extrusions • A lign the 3 screw holes on bottom of pedestal with the 3 holes in the base such that the power cord holder is at the rear of the unit . (Fig. 3) • S ecure the base assembly to the pedestal by inserting and Base Assembly tightening the 3 screws in the 3 holes located on the bottom Fig. 3...

  • Page 4: Cord Management

    CORD MANAGEMENT The cord management feature is located on the back side Fig. 8a Fig. 8b of the fan. Simply double up the excess cord length, and place the two pieces of cord in the notch (Fig 8b). The notch will hold the cord so that the excess length will not drag on the ground. ASSEMBLY INSTRUCTIONS REMOTE CONTROL BATTERY INSTALLATION/ REPLACEMENT INSTRUCTIONS Fig. 9 A. Remove battery door by sliding downward in direction of arrow. B. Insert 2 AAA batteries into the remote following the directional guides in the recessed slots (Fig. 9). Batteries are included. C. R eplace battery door by sliding upward opposite of arrow direction until door snaps in place. NOTE: DO NOT MIX OLD AND NEW BATTERIES. DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES. SEE RECYCLERS IN YOUR AREA FOR PROPER DISPOSAL OF BATTERIES. HY-254 SERIES FAN OPERATION FAN OPERATION FAN OPERATION On/Off Model HY-254 To turn fan on, press the Power button ( ) located on the left side of the control panel.
  • Page 5 HY-254 SERIES REMOTE CONTROL OPERATION On/Off Press the Power button ( ) once to turn the fan on. Press the Power button a second time to turn the fan off. Speed Control The fan will automatically start on “Sleep” speed when initially turned on. To adjust the speed up or down, press the Fan Speed button ( ) repeatedly to increase level Oscillation Fig. 10 To activate the Oscillation feature, press the Oscillation button ( ) once. Press the Oscillation button again to turn the Oscillation feature off. Remote Control Storage When it is not in use, the remote control may be stored in the recessed area located behind the controls (Fig. 10). HY-280 SERIES FAN OPERATION On/Off Model HY-280 To turn fan on, press the Power button ( ) located on the left side of the control panel.

  • Page 6: Speed Control

    HY-280 SERIES FAN OPERATION CONTINUED Temperature Model HY-280 A. Press and hold the Temperature Control ® Button to enter temperature mode. B. C urrent room temperature is displayed for 3 seconds, then display begins to flash at 1 second intervals. If temperature is not selected, unit will revert back to “speed mode” after 10 seconds. C. P ress the temperature button repeatedly to increase the temperature by one degree intervals starting from room temperature. You will have to cycle through 90° to get back to the 60° point. (This is the minimum.) For Canada, the temperature cycle range is 15°C to 30°C. D. O nce the desired temperature is selected, the fan will revert back to room temperature display. Note: The fan speed will adjust automatically to achieve the desired temperature. The fan will stop if the room temperature drops below setpoint and will turn on again if the room temperature climbs above setpoint. • If the user hits the “Power” button, this will override all functions and the unit will shut “OFF”. The temperature setting will be cleared. • If the Timer button is selected, the temperature will not be affected. The chosen temperature will remain in effect and the room temperature will continue to be displayed. Timer will function with or without Temperature Mode.

  • Page 7: Remote Control Storage

    HY-280 SERIES REMOTE CONTROL OPERATION CONTINUED Temperature Mode can be accessed through the remote control. A. Press the Temperature Mode button ( ) once and release. Fig. 11 Display will begin to flash. B. Press the “+” and “-” buttons to change the setpoint. Note: Once the setpoint is selected, the fan speed will adjust automatically to achieve the desired temperature. The fan will stop if the room temperature drops below the setpoint and will restart if the room temperature climbs above the setpoint. Remote Control Storage When it is not in use, the remote control may be stored in the recessed area located behind the controls (Fig. 11). USER SERVICING INSTRUCTIONS CLEANING AND STORAGE • Ensure the fan is turned off and unplugged. •...

Table of Contents