DIGISYSTEM POS-7650 Instruction Manual

80mm series thermal receipt printer

Hide thumbs

Table of Contents

Quick Links

Download this manual

80mm Series Thermal Receipt Printer

Instruction Manual

Table of Contents

Need help?

Do you have a question about the POS-7650 and is the answer not in the manual?

Questions and answers

Summary of Contents for DIGISYSTEM POS-7650

Page 1 80mm Series Thermal Receipt Printer Instruction Manual...
Page 2 Version Feb,2016 All rights reserved & Intellectual Property Rights Protected It contains proprietary information protected by Copyright, No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission from us.
Page 3: Safety Precautions
Safety Precautions This section presents important information intended to ensure safe and effective use of this printer. WARMING: Scratch Warning: Never try to touch the auto cutter or jagged teeth. ！！ Scald Warning:To avoid been burned, please do not touch the printer head . ！...
Page 4: Product Information
1.Product Information Our Newly 80mm Thermal printer possesses following features: - High-quality printing,High-speed and strong stability; - Interface ( Serial / RJ45 Ethernet / USB /WiFi ) - Android device support if connect with USB /WiFi method; - IOS device support if connect with RJ45 Ethernet / WiFi method; 1.1 Technical Parameters and Features Printer Method Line Thermal...
Page 5: Usb Cable
1.2 Application: It can be used for all kinds of commercial in retail POS systems, Restaurant system, Industrial control systems in areas such as. •Light weight and portable •Beautiful shape •Low cost and High-quality thermal printing •Cash drawer drive supported •Easy paper-roll installation, Easy maintenance and Rational structure •Low-power waste, low-run cost (without the ribbons, ink cartridges) •Built-in data buffers (be capable of receiving print data while printing)
Page 6: Communication Ports
2.Communication Ports 2.1 Universal Serial Bus（USB Port） Connect the printer with the standard usb cable(usb device types are automatically) , once printer is connected with the PC, install the driver , then choose the corresponding port accordingly. RJ45 Ethernet Port (10M/100M) (suitable for 80-III type) With this port, we can use the network cable and connect the computer directly, communication and the port number is 9100;...
Page 7: Basic Function Operation
•Data Length: 8 Bits •1bit Stop Bit: 1Bit •Parity: None The wiring method of the serial interface printer following the standard rules of Serial Interface EIA standard. Consumer can get the current default baud rate from “ Print Test Page ”and also can adjust the baud rate via DIP switch ( DIP switch is on the bottom of the printer ) 3.Basic Function Operation 3.1 Indicator Light &...
Page 8: Cleaning Steps
release the “FEED” button about 3 seconds after the “ ERROR” indicator off ; The way to quit Hexadecimal printing model is just press “ FEED” button by three times. • Aging model printing: power off the printer, press “ FEED” and hold it until the “...
Page 9: Installation Wizard
2. We have to wait for a while if we just finished the printing. Use a soft brush or wrung-out ethanol immerged cotton to clean the print head. Remember to turn on the gear while lubricating to ensure a completely lubricated;...
Page 10 1、Select the language you need and click the button”Confirm”,and show the imgae as below,then click the button”next step 3 、please read the related terms carefully,and install it as agreement as below...
Page 11 4 、 Click”next step” ans show as below(customer is available for modifying channel of driver installation or default one)
Page 12 5 、Click the button”next step”again and show as below and install it: 6、After installation,the related interface will be shown as below,select operation...
Page 13 system of your computer and printer model,click”USB port for testing”, if you communication with USB port, USB port of computer will be identified automatically .Click he button”next step”and install continuously as below : 7、Click the button”Start Installation” and shown as below. And select installation:...
Page 14 8.Finish the driver installation as below:...
Page 15: Usb Port Connection
5.2.1 USB Port Connection ( If your desired port is USB ) 1: Open “ Properties “ then choose “ Ports ”...
Page 16 We can see many usb ports if there is other usb printer used in this PC. Select the unoccupied usb port and click “Apply” Remarks: Ensure the printer is power on & cable connects to the computer for the time use. Or we can not find “ USB001” ; check if we can find “ USB Print supporting ”in below location : Path: My Computer - Properties - Management - Devices Manager - Universal Serial Bus Controller ), if not , please recheck the cable and printer connecting way.
Page 17: Ethernet Connection
If the print test page works well, that mean all setting is ok. Remarks: If “ Printer Error “ , we should back to “ Ports” and try the USB ports one by one until it is ok. 5.2.2 Ethernet Connection ( If your desired port is Ethernet 1: Get the IP address from a Self Printing Test Paper Switch off the printer then press “FEED”...
Page 18 Open “ Properties” then click “ Ports ” 2: Select “ Add Port”we can see below jpg...
Page 19 3: Click “ Next ” 4: Next and choose “ Generic Network Card “ then click Next...
Page 20 5: Next 6: Click Finished and we can check the added ports as below jpg...
Page 21 7: Let’s back to “General”and click “Print Test Page ” If the print test page works well, that mean all setting is ok. We can also change the setting by clicking “ Device Settings ” ( print method...
Page 22 setting ,cash drawer setting, paper cutter setting etc ) - Below jpg for reference ; 5.2.3 Serial Port Connecting ( If your desired port is Serial ) 1: Following “ Printer - Properties - Ports ” as below...
Page 23 2: Select “COM1” - “Configure Port ” - default setting as below jpg...
Page 24 We should refer to the default baud rate from the self test page and input the same baud rate above or there will be error in the printing. Once setting parameters confirm, click “ Apply “ we come to below jpg; Click “...
Page 25 3: Back to “ General”and try “ Print Test Page” If the print test page works well, that mean all setting is ok. Try below setting if we the printing speed is too slow: - Cl ick “ Device Settings “ ---- “Print Mode” ---- select “ Print as soft font “...
Page 26 5.2.4 Bluetooth port to be used (if you choose models support Bluetooth printing) 1: Make sure you are using the device (such as a laptop) is Bluetooth-enabled, then activate Bluetooth, Bluetooth started successfully, you can see the computer icon on the bottom right of the display.
Page 27 2:Power on the Bluetooth printer. 3:To add the Bluetooth printer, please left-click the click “Add a Bluetooth Device” ,then you will enter wizard screen , please choose “My device is set up according and ready to be found”click “Next”(showed as below).
Page 28 4:if you can see screen as below,then the device is searching the bluetooth printer,please wait.
Page 29 5:Once the Bluetooth printer is found. You can see it listed on the screen, Here, for example,LY80 Bluetooth printer is successfully found. Please click “-LY80”, click “Next” 6:Choose “Let me choose my own passkey”, then enter “1234”(this is factory default passkey, if you want to change it, you have to inform us to set the new passkey for you in our factory before shipping),then click “Next”.
Page 30 7:if you can see the screen as below, that means the Bluetooth printer is already connected. Please notice the assigned COM ports ,then Click”Finish”.
Page 31 (Note: The Bluetooth device will automatically assign a COM port.) 8: Now if you want to test if the printer is OK to print, you could use a com tool , and send printed data to Outgoing COM port( just as above image shown: COM5). (Com tool setting is 9600,N,8,1.) 6.
Page 32 Image 6.1 3, modify the IP address of the computer and printer are in the same network segment, subnet mask and gateway set to the same printer. As shown in “image 6.2”, and then press the "OK"...
Page 33 Image 6.2 4, open the PC browser, enter the IP address on the self-test page in the browser address bar, as shown in “image 6.3” Enter after entering the link. Enter into the interface shown in “image 6.4”. Image 6.3 Image 6.4 Information 2, choose the left “Configuration”...
Page 34 Image 6.5 Configuration 3, restart the printer, enter the IP address of the modified computer inside the browser address bar, enter the printer settings link. 4, re-enter the web will be displayed after the relevant Ethernet modify information on the new settings page after page, then you can enter the Printer Test option which test the printer can achieve normal correlation function, as shown in “Image 6.6”.
Page 35 Image 6.6 Printer test 7,: normally we don’t advise clients to modify the printer Mac address, as that "Mac Address" option “image 6.5” interface, because arp cache problem router or computer can cause the system to wait after modifying the Mac automatically refresh or that manually refresh arp after the cache in order to properly connect the printer to the computer, to achieve a normal Ethernet communication;...
Page 36 Image 6.7 Run “cmd” Image 6.8 DOS environment 3, type arp -d at the interface shown in “Image 6.7”, as shown in the drawings 6.8 Enter after running.
Page 37 Image 6.9 run “arp -d” 4, After the operation the operation to the printer on again, this time to go up the interface shown in “image 6.9” ping the printer, the format for ping ip address (eg ping 192.168.1.100), as shown in “Image 6.10”. As follows after the ping can reply to the white box shown in “Image 6.10”...
Page 38 Image 6.10 Test connection 7.WIFI IP Address Setting The setting parameters of 80 wifi thermal printer through the browser configured, the steps as below: 1, Plug and switch on the printer. 2,Find the wireless network and link it. Then find the file named “ HF-A11” and link it –...
Page 39 Enter “ admin” for the user name and default password is also “admin”. Press ok and then Next: Select “AP+STA mode” , and save. Note: When the module is selected to STA mode (NIC), then re-start the module, you can not reuse the wireless configuration, SSID number can not be found.
Page 40 4, Select “ STA Setting ” as below; 5, Then click “Scan”, it will appear selection as below: Above are all your current wireless network, select one of your wireless device available to be used, then click “ OK ”.
Page 41 6, Input the correct configuration within the dialog, as below: STA setting is complete, click "save". 7, Select "Other Setting", setting as below: After finish the setting, click “ Save”.
Page 42 8,Restart the module, as below: Module configuration is complete 9, Click computer “Start” “ Run”, Input word “CMD”，as below： Input “ping 192.168.1.105 -t” as below...
Page 43 If details shows as below , means connection is Ok Return to the driver -" properties " - " port "-" add port ", consistent with the add ports: 8.Operating Manual for Android OS This manual applies to all of our android OS compatible printers...
Page 44 ( both 58mm & 80mm width printer) Currently, the common communication ports we used for android OS are ( USB、Ethernet、Bluetooth and WiFi ) If you want to use Android Device connected with our printer, first of all make sure that printers can be supported Android Operate System, proceed as follows ( Bluetooth as example): Step 1: - Insert the CD driver disc into the CD-ROM, connect your cell...
Page 45 Step 4: - Find this icon and open it. (Ethernet interface need to enter the IP, you can get it from the self-test page, WIFI need to enter your IP of own setting), click on the "Connect Printer" after the connection successfully, click on the "Print Test Page", the printer will work.
Page 46 9.Operating Manual for IOS APP 1. Download the Test Tools “Printer-X” from App Store,as below: (Image 1) 2. Turn on the Apple mobile Bluetooth , then click “Printer-X”:...
Page 47 (Image 2) 3. In“Printer-X”will search “BlueTooth Printer” (Image 3)
Page 48 4. Connect successful, put content into Edit Box to test printing. Test: bold, underline, double width, double height, (minimum font) (Image 4)
Page 49: General Troubleshooting
(Image 5) 10.General Troubleshooting 1: Why serial port printer printing messy code? Ensure the baud rate setting in the PC is same as the printer baud rate. ( we can see printer baud rate from self test page) 2: Self printing test is ok,but printer does not work after driver installation. Recheck the installation according to above installation wizard and see if we selected the right port or ask service center for advice if needed.
Page 50 8: Messy code printing except Arabic numeral printing. language switching incorrectly,please turn on the SW-4 switch on the DIP switches. 9: Fuzzy printing of Chinese character ON Please turn on the SW-3 switch ( DIP switches on the bottom of the printer ) 10: Malfunction of the auto paper cutting See if the SW-1 is off and ensure the cutting function is Enabled or...
Page 51 Solution for 2. Please replace the printer head and try again. Contact service center for repair if same problem after replace the printer head. 17: How can we reset to default setting? Find the card slot on the bottom of the printer.Press the black key ( just press and release ---Reset the IP to default Only ) 18: How to reset the WiFi default setting? A:Find the card slot on the bottom of the printer.Press the black key &...