Page 1
Application case B: Configure MR-900W for connecting web video device Application case C: Configuring MR-900W for serial port DTU function Application case D: Configuring MR-900W for using Ethernet port and serial port simultaneously Application case E: MR-900W used for remote connecting to LAN by VPN...
Page 2
Brief Introduction Thank you for choosing E-Tung high speed WCDMA 3G product MR-900W。This manual will help you to know the function and usage of this product. Please read carefully about this manual. MR-900W Specification Product Outlook Port RJ45 Serial Port RS232...
Page 3
Data interface :RS232/RJ45 Network:WCDMA network Buffer Size:RAM 64M FLASH 4M Frequency:UMTS/HSDPA/HSDPA850/1900/2100MHz Quad-BandGSM850/900/1800/1900MHz Working Temperature:-25℃ ~ +70℃ Working Max Humidity:95%@+40℃ Size:80x104x38mm (Not include antenna and mounting kit) Basic Function Adjustable Network Interface IP Supporting NAT Online Sharing Supporting DHCP Server Supporting DNS Proxy Supporting Interface Mapping Supporting DMZ Host(IP Address Mapping)...
Page 4
MR-900W Serial Port Configuration(Standard RS-232 DB9 Female Port)Socket definition is as following: Types RS-232 Socket Definition RXD(out) TXD(in) MR-900W user serial port: Types RS-232 RS-485 Socket Definition RXD(in) TXD(out) RTS(out) CTS(in) Accessory 3G Sucking Antenna Cross Cable...
Page 5
Power Supplier MR-900W Common Networking Application Chart...
Page 7
MR-900W Configuration Procedure Step 1:Plug in cables • Put in the SIM card with WCDMA function • Using a cross cable to connect MR-900W’s Ethernet port with a computer’s Ethernet port • Plug in Power Supplier Step 2:Sign in for configuration •...
Page 8
Application case A: Configure MR-900W for high-speed internet connection MR-900W may be directly connected to one computer Ethernet port to achieve wireless online, and also it may be connected to a switcher or a HUB to make a few computers sharing the internet. We will illustrate these 2 types of connection as following.
Page 9
If you would like to set a IP address for MR-900W, then you should set the IP address for MR-900W as 192.168.1.1,and IP address as 192.168.1.20,(as show in the following figure):...
Page 10
(3) Put an WCDMA SIM card into the MR-900W wireless router, and turn on the power. MR-900W will dial up for online automatically, then we can browse website and send/receive email. We can also check the device’s working status through the following interface. We Key in “http://192.168.1.1” on the address bar, and then type in the user name as “root”...
Set up procedure: (1) Connecting MR-900W to the upstream port of a switcher or a HUB through a cross cable, and connecting all the computers which are in the network to the downstream port of the switcher or the HUB.
Page 12
If you would like to set a IP address for MR-900W, then you should set the IP address for MR-900W as 192.168.1.1,and IP address as 192.168.1.20,(as explained above ): (3) Put a WCDMA SIM card into the MR-900W wireless router, and turn on the power. MR-900W will dial up for online automatically, then we can browse website and send/receive email.
Page 13
Log into the configuring interface for MR-900W. The default gateway IP address for MR-900W is “192.168.1.1”,Please key in “http://192.168.1.1” on the IE browser,and then put user name as “root” and password as “1234”. You will be able to see the configuring interface for MR-900W. (As show in the following figure:...
Page 14
The IP address we get from WCDMA is the dynamic IP (IP address changes for each dialing online). If we configure the DDNS for MR-900W, then we can access the device, no matter what IP address we get from each dialing.
Page 15
Configuring DMZ Host: Log-into MR-900W configuration interface, and configure the IP address of web camera as the IP address of DMZ host from MR-900W. After all these steps, click on “restart”, and restart the device. 3. Video Access First, set up the MR-900W and then connect the MR-900W to webcam network port with a crossover cable, and then turn on the power for both devices.
Page 16
Must use crossover cable for connecting MR-900W to computer and webcam; MR-900W and the network camera must be in the same network segment. The factory default gateway IP for MR-900W is: 192.168.1.1, therefore you should set up the webcam’s IP between 192.168.1.2 and 192.168.1.254.
Page 17
When the MR-900W connected to the mServer, it will appear online on the mServer. At this point, the MR-900W can be mapped to a virtual serial port or a TCP port over mServer. It can also remotely send and receive data through DCC interface and PC software.
Page 18
2、 Configuring MR-900W You may go to the configuring interface and setup the following parameter (As show in the following figure): IP address (or domain name) for primary data center primary data center port user serial port configuration (match to PLC serial port parameter) Then, configure the parameter for network camera (configuring DMZ host and DDNS).
Page 19
When the MR-900W connected to the mServer, it will appear online on the mServer. At this point, the MR-900W can be mapped to a virtual serial port or a TCP port over mServer. It can also remotely send and receive data through DCC interface and PC software. At the same time, you may type in configured domain name into the IE browser, and visit the device that connecting to MR-900W.
Page 20
MR-900W Remote Access LAN by using VPN Mode 2. Hardware and network preparation One network router supporting VPN function (Supporting PPTP connecting mode as well), This router connects to a LAN and is able to access internet, One set MR-900W(Include accessory),...
Page 21
Of cause, the configuration interface and the selection items could be different for various routers. Configuring MR-900W Login the configuration interface for MR-900W, and click on “VPN function” for the following configuration: Type ——PPTP IP or domain name for VPN server —— The corporate LAN side IP (If the corporate LAN side IP is not fix, then you may acquire a domain name and type in the domain name here) User name ——...
Page 22
Check for dialing up status After login MR-900W, we may check the dialing up status as show in the following figure:...
Page 23
LAN, you may access to the login interface for MR-900 and, other data information within the LAN as well. As this point, if the MR-900W was connected to a video server, and made a port mapping or DMZ host, you may access to video surveillance by visiting “http://192.168.0.207” within the corporate LAN.
Page 24
Example 1 Configuring MR-900W to be connected with AIXS 205 (webcam) for wireless video surveillance 1. System structure 2. Hardware preparation 1、 One set MR-900W (include accessory) 2、 One WCDMA card 3、 One AXIS 205 network camera 4、 One computer with internet connection 3.
Page 25
The IP address we get from WCDMA is the dynamic IP (IP address changes for each dialing online). If we configure the DDNS for MR-900W, then we can access the device, no matter what IP address we get from each dialing.
Page 26
Configuring DMZ Host: Log-into MR-900W configuration interface, and configure the IP address of web camera as the IP address of DMZ host from MR-900W. After all these steps, click on “restart”, and restart the device. (as show in the following figure)
Page 27
Must use crossover cable for connecting MR-900W to computer and webcam; MR-900W and the network camera must be in the same network segment. The factory default gateway IP for MR-900W is: 192.168.1.1, therefore you should set up the webcam’s IP between 192.168.1.2 and 192.168.1.254.
Page 28
One computer with internet connection 2. System Setup Setup mServer on your server See mServer setup manual, or call us at +86-10-64880675. First-time customer can also use Etung’s testing server, and the IP address for mServer is 123.196.114.95, port 7000. Read-Back control card information You may connect the C-Power5000(DS06T) control card to the computer through the serial port, run LedCenterM (3.51version) software, and define a LED screen corresponding to a C-Power5000(DS06T)
Page 29
After defining the serial communication with the LED screen, you may read-back the current control card information. (As show in the figure)
Page 30
IP, 5200 for port, and “192.168.1.1” for gateway. Configuring MR-900W 1) Turn on the power for MR-900W, and connect to the computer with a crossover cable (note: set the computer as obtain IP address automatically). You may type in http://192.168.1.1 to log into web configuring interface for MR-900W.
Page 31
The IP and port for this User Agent Client is the IP and port that just read-back from the LED control card. After setup click on “restart”, at this point, the MR-900W is connecting with LED control card with the crossover...
Page 32
Configuring LED control card to connecting with MR-900W 1) When the MR-900W is connected to the mServer, you may find it appear as on line on mServe. At this time, you may map the MR-900W to TCP port 5200 by selecting the MR-900W and then click “Mapping Management”...
Page 33
As show in the figure, you may change the communication mode as networking communication mode. If you would like to use Etung’s server, the IP address would be showing in the figure. If you install mServer and LedCenterM3.51 on the same computer then the IP address could be 127.0.0.1. If you install mServer and LedCenterM3.51 on different computers but in the same LAN, then you may set the IP as a LAN IP such as...
Page 34
Since the TCP port 5200 has been occupied by ① MR-900W, you need to map the ② MR-900W to a port other than TCP 5200 port over the mServer, such as TCP 5300 port.
Page 35
Appendix MR-900W Configuration Menu Description...
Page 38
Within the WCDMA network, the device obtains a random IP for each dial-up, so the IP changes time to time, and it cause to trouble for remote access. In order to facilitate access, MR-900W bundled with Dynamic Domain Name software. You may apply for a free domain name, and then configure this domain name in DDNS of MR-900W.
Page 39
How to restore factory settings In IE browser, enter the Ethernet IP (default is 192.168.1.1) to login the configuring interface for MR-900W Click on “System tool” “restore factory settings” After step (b), the device will restart, and finish restore factory settings...
Page 40
How to update firmware 1、 Get the update firmware for MR-900W from the manufacture (.img software) 2、 In IE browser, enter MR-900W’s Ethernet port IP (default 192.168.1.1), and login the configuration interface of MR-900W. 3、 Click on “System Tools” “Update firmware”, and then select the firmware that need to update, and click on “Upload”...
Page 41
Check the working status for the device: Inside the configuring interface of MR-900W, Click on “System Tools”, if you would like to view the dialing status for MR-900W, then click on “System Log”. For the connecting status with data center, you may click...
Page 42
Trouble shoot for device cannot on-line Step 1: check if SIM card can access internet and all accessories are properly connected to the device...
Page 43
Step 2: Check the configuration of user equipment Others Welcome to visit our website at “http://www.etungtech.com.cn” or call us at 010-64880675 Etung Technology Co., Ltd. 305 GengFang Plaza, Jia 13 Huayuan Road, Haidian District Beijing, Chian TEL: 010-64880675 FAX: 010-64857815...
Need help?
Do you have a question about the MR-900W and is the answer not in the manual?
Questions and answers