Advertisement
Quick Links
Introduction：
XC4697 is a USB 3.0 enabled dual-SATA hard drive
enclosure. It supports simultaneous use of two 2.5" or 3.5"
SATA hard disk for both data read and data write. It also
backward compatible with USB 2.0 and USB 1.1. The
maximum transfer speed of USB 3.0 can reach 5Gbps. The
actual transfer speed of XC4697 is 400M/s.It supports Offline
Clone, which is able to copy data and system files from Source
HDD to Target HDD completely via finger touch. XC4697
provides high storage capacity, high data transfer rate, and best
data protection.
Function Chart：
1、 Power indicator 2、 Bay 'A' indicator 3、 Bay 'B' indicator
4、Clone processing indicator
7、 Bay 'A'
10、DC input
XC4697 Manual
8、 USB3.0 input
5、Clone button 6、 Bay 'B'
9、 Power switch (ON/OFF)
- 1 -
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Jaycar Electronics XC4697
- Page 1 XC4697 Manual Introduction： XC4697 is a USB 3.0 enabled dual-SATA hard drive enclosure. It supports simultaneous use of two 2.5” or 3.5” SATA hard disk for both data read and data write. It also backward compatible with USB 2.0 and USB 1.1. The maximum transfer speed of USB 3.0 can reach 5Gbps.
- Page 2 Caution: 1. Once using E-SATA interface, it can only recognize one HDD in PC. If 2 HDDs are inserted in the dock, it can only recognize Bay ‘A’ HDD. If only insert one HDD in the dock, both Bay’A’ and Bay ’B’...
- Page 3 CLONE: Please note the below conditions before clone: Bay ‘A’ = SOURCE HDD, Bay ’B’ = TARGET HDD TARGET HDD ‘s capacity MUST be larger than SOURCE HDD, otherwise the CLONE cannot be completed. (Same capacity is also not acceptable) Before CLONE function starts, make sure the information TARGET HDD is not important;...
- Page 4 Bays indicators are on, that means XC4697 is ready for clone. c、Press and hold the clone button for 3 seconds until the indicator light is on, press the button once more for Clone confirmation. Offline clone is starting to process.
- Page 5 d、Clone progress indicator flashes and shows the progress (25%, 50%, 75%, 100%). e、Once clone is finished, all progress indicators will light up. f、Turn off power and take out the HDD carefully - 5 -...
- Page 6 2, USB Clone Drive Installation a、Please insert the CD drive and click “setup.exe”. Choose your language and click “ Next” b、Fill in the S/N # accordingly (you can find the S/N# on the cover of CD drive) - 6 -...
- Page 7 c、Click “Install” for installation d、Installation progress is showed - 7 -...
- Page 8 3, Clone from Source HDD to Target HDD a、Please insert Source HDD and Target HDD well to the docking, connect XC4697 to PC via USB cable. Turn on the power, you can find the clone icon on the right bottom of window, then double click the CLONE Icon to start the program.
- Page 9 b、Clone drive activated, please click “Start” c、Press start to proceed with Clone. - 9 -...
- Page 10 d、Clone progress is showed e、Click “OK” once clone is finished - 10 -...
- Page 11 f、You should find the same contents of Source HDD in Target g、If your target HDD has extra space, the system will allocate it to “unallocated” area automatically, please refer to the below picture. （Windows system only allows a maximum of four primary partitions, if the original disc already exist four primary partitions, then it can not distinguish the extra space but logical drives can have more than one ）...
- Page 12 HDD Partition a、Open Disk management and select the unallocated area b、Right click 〝New partition〞for further action - 12 -...
- Page 13 c、“Next” d、Base on your need and click “Next” - 13 -...
- Page 14 e、Please enter the new partition capacity and click “Next” for further action f、Assign the drive letter and “Next” - 14 -...
- Page 15 g、Select “quick format” to format the new partition h、Click “finish” - 15 -...
- Page 16 i、Partition completed, the new partition can be found. - 16 -...
Need help?
Do you have a question about the XC4697 and is the answer not in the manual?
Questions and answers
does it require software
Yes, the Jaycar XC4697 requires software installation for some functions. According to the manual, users must insert a CD, run “setup.exe,” and complete the installation process. Additionally, software is used to perform cloning operations.
This answer is automatically generated