Do you have a question about the Phontech 6200 and is the answer not in the manual?
Questions and answers
Summary of Contents for jotron Phontech 6200
Page 2
Amendment Record INIT DATE CHAPTERS VERSION REASON FOR CHANGE K.A.T. 01.09.14 Initial release Jotron AS| Phontech 6200: Call Logging Unit Page ii P/N: 89459 (v.A)
Page 3
The information in this book has been carefully checked and is believed to be accurate. However, no responsibility is assumed for inaccuracies. Jotron AS reserves the right to make changes without further notice to any products or modules described herein to improve reliability, function or design. Jotron AS does not assume any liability arising out of the application or use of the described product.
You can also find the address of the call logging unit by looking in the “Information” menu on the front panel display on the physical unit. Click any of the navigation buttons to clear the “Jotron” logo and click the “Enter” button when you are at the “Information” menu item. Then click “Enter” again on the “Number and IP”...
To see detailed call reports for a single user, click on the extension for that particular user. This will open the page for this individual user which is further explained in chapter 1.3. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-2...
To see the detailed call log for a given PIN click on the PIN number in the left most column. This will show the individual PIN page which is further explained in chapter 1.3. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-3...
“Export XML” button. Note that this will change the balances of all the users and pins that are located in the import file. This operation cannot be undone. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-4...
Billed - The number of seconds that should be billed for the call. This does not include the time taken by the user to dial or enter a pin number. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-5...
Those calls include calls between users inside the system and incoming calls if enabled through the Phontech 6200 Storage Configuration. Under the call log list there’s a filter button so you can change if the log should display billed calls only or include the documentation lines as well.
‘Documentation’ will have billing seconds set to 0 as they are only present to document the call, not bill it. Those calls include calls between users inside the system and incoming calls if enabled through the Phontech 6200 Storage Configuration. ...
If pre-paid billing meters are active on trunk lines the users and/or PINs in use must have a positive balance equal to that of at least 1 minute worth before they can be used to access a trunk line. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-8...
Note that any change to the configured rates will not affect already logged calls. Only new calls made after the change to the rates will be affected. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-9 P/N: 89459 (v.A)
Page 14
‘_’ will allow the previous number or match to be repeated multiple times. This may be used to match numbers of arbitrary lengths. Some examples are shown below. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-10...
‘Delete’ button it will delete all records that are older than the given date. Note that this operation is irreversible. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-11 P/N: 89459 (v.A)
Page 16
You can also perform a factory reset by clicking the ‘Factory reset’ button at the bottom of the page. This will delete all information visible in the web interface such as billing rates, balances and call records. Jotron AS| Phontech 6200: Call Logging Unit Web Interface Page 1-12 P/N: 89459 (v.A)
Need help?
Do you have a question about the Phontech 6200 and is the answer not in the manual?
Questions and answers