Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Easylam EXPERT 140 C
- Page 1 Laminator EXPERT 140 C Operating instructions Version 1.2...
-
Page 2: Technical Information
Please read this operating instructions before installation and keep this for later use technical information model ......................EASYLAM EXPERT 140C length ......................175 cm width ......................50 cm height ......................135 cm height working area ..................970 cm max. media width ...................143 cm usable roll length ....................1420 mm max. -
Page 3: Electricity Connection
Further advises for installation: Power supply: The connection sockets have to be close to the machine. • single-phase current 110 V - 230 V • frequency: 50 – 60 Hz • strength of electric current: 5 A Location The location to place the machine must provide enough space to work. Don’t forget that space is also needed to insert and remove the material. - Page 4 - 4 -...
-
Page 5: Safety Devices
Make sure that your hands do not get between the rolls while the machine is ope- rating. EMBLEM EASYLAM EXPERT 140C is eqipped with a safety mechanism which uses a slip clutch to stop the rotation of the rollers. In this way serious inju- ries or pinching of the fingers are avoided. -
Page 6: Operation Of The Machine
Operation of the machine When you start working stay directly in front of the machine. The laminator has to be turned on with the main switch (right down, inside the machine). The main switch is lighted in green. With the keys SPEED I or SPEED II you decide the speed of lamination. You can also use the footpedal to adjust the speed of the laminator. - Page 7 Insert the scroller into the right Insert the scroller into the right insert this end of the scroller into connection. Move the scroller that connection. Move the scroller that the left connection way, so the pin fits into the holding way, so the pin fits into the holding fixture.
- Page 8 EASYLAM-CUTTER To equip your laminator with lamination fi lm in a simple and economical way we recommend our EASYLAM-CUTTER (Art.-Nr.: 24959). Its knife has a special blade to minimize the danger of getting hurt or of damaging the rolls considerably. Advantages: you save time and material while insertingthe lamination fi lm including liner no exposed knife point The following description of the procedure allows an economical consumption of the lamination fi lm while equipping the lamina- tor with foil. The cutter simplifi es the preparation of the machine and helps to learn it faster. You can get this tool at your local dealer or at www.dataplot.de.
- Page 9 Place the lamination film between Hold the film tight and clamp the Make sure the lamination film is the rollers rollers rolled tight Feed foreward approx. 5cm of Position the blund part of the knife Cut the liner carefully lamination film between film and liner Use the sharp end in front of the Fix the liner to the core...
- Page 10 Laminate with backing paper: • Open the lamination roller by pressing the button MANUAL Ç/È and put in the laminate as shown in the pic- ture. Push an empty roller core onto the roll-up axle R3 so that the protective liner/backing paper can be rolled • After you have attached the laminate to the roll-down axle R4, separate the backing paper and use tape to fas- ten it to the cardboard core on the roll-up axle R3. Ensure that the protective liner has been fastened uniformly without cross creases.
- Page 11 Proceed as described above for simultaneous lamination of both sides. Also use the roll-down axle R1 and roll-up axle R2 • First mount the material and the empty roller core onto the lower roll-down and roll-up axles R1 and R2 • Both cores used have to be of the same width. Mount them so that they are line up precisely with each other. To achieve this, measure the distance to both sides of the rollers. Mounting already laminated paper material to a sheet. • Take a base plate that is already equipped with double-sided adhesive film.
- Page 12 Montage von geschütztem mit doppelseitiger Klebefolie beschichtetem Bild LINER PICTURE RUBBER ROLLER SHEET Montage von geschütztem Bild auf eine bereits mit doppelseitiger Klebefolie beschichtete Platte LINER PICTURE RUBBER ROLLER SHEET - 12 -...
- Page 13 Company manufacturer of the brand EMBLEM, declares under our own responsibility, that the machine: Brand: EMBLEM Model: Easylam Expert 140C Easylam Expert 160C Easylam 160W Is in conformity with: The requirements of EU Directive 2006/42/EC. The requirements of EU Directive 2004/108/EC.
- Page 14 - 14 -...
- Page 15 - 15 -...
- Page 16 Dataplot GmbH • Gutenbergstraße 15 • D–24558 Henstedt–Ulzburg • Germany Tel. +49 41 93 995 0 • Fax +49 41 93 995 220 info@dataplot.de • www.dataplot.de - 16 -...