Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Golden Motor EPO-03HP
- Page 3 To the owner Concerning this manual, please consult your Thank you for choosing a ELECTRIC ELECTRIC PROPULSION OUTBOARD KIT dealer. To PROPULSION OUTBOARD KIT.This Owner’s Manual ensure long product life, ELECTRIC PROPULSION contains information needed for proper OUTBOARD KIT recommends that you use the operation,maintenance and care.
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1 Safety Information 1.1 Outboard motor safety 1.2 Boating safety 2 Components and Specification 2.1 Tiller Control Version 2.2 Teleflex Remote Control Version 2.3 Specification 2.4 Wire Connection 2.5 Safety Notice 2.51 Safety red cord 3 Operation 4 Maintenance 5 Return and Repairs 6 Warranty... -
Page 5: Safety Information
1 Safety Information 1.2 Boating safety This section includes a few of the many important 1.1 Outboard motor safety safety precautions that you should follow when boating. Propeller Alcohol and drugs People can be injured or killed if they come in contact with the propeller. -
Page 6: Passenger Training
make it hard for others to avoid you or Standing or sitting in non-designated Understand where you are going. locations may result in being thrown either · Avoid areas with submerged objects or shallow overboard or within the boat due to waves, wakes, water. -
Page 7: Components And Specification
2 Components and Specifications 2.1 Tiller Control Version... - Page 8 ⑦ ⑤ ⑥ ④ ② ③ ① ①speed display :0-`100% 100% is the max WARNING! Attach the “cord “to a secure place on speed. ; your clothing, or your arm or leg while operating. Do ②Twist throttle:you twist it to start the motor not attach the”...
-
Page 9: Teleflex Remote Control Version
2.2 Teleflex Remote Control Version... - Page 10 ① ① press the power switch ②:Put forward the remote speed ②: control joystick set,so that the boat will go forward, at the same time , ③:Manipulate the stainless steel steering wheel,when you need to turn a corner or change direction ③...
-
Page 11: Specification
2.3 Specification Golden Motor Technology Co Ltd Electric Propulsion Outboards Specifications （Item Measurement NO.) EPO-03HP EPO-06HP EPO-10HP(L/S) EPO-15HP(L/S) EPO-20HP(L/S) units Parameter Length mm(in.) 960（37.8） 873（34.4） 873（34.4） 873（34.4） Width mm(in.) 450（17.7） 332（13.1） 332（13.1） 332（13.1） S：1040（40.9） S：1040（40.9） S：1040（40.9） Height mm(in.) 310（12.2） 1011（39.8）... -
Page 12: Wire Connection
2.4 Wire Connection... -
Page 13: Safety Notice
2.5Safety Notice 2.51Safety red cord The” Fuse” must be attached to the “button “for the motor to run. The “cord” should Be attached to a secure place on the operator’s clothing, or arm or leg. Should the operator fall overboard or leave the helm, the “cord “will pull out the”... - Page 14 2.52 Battery Power Connection Notice That is the power wire,red is “+” and black is “-”,when you get the outboard,what you need to do is to connect this power wires,bear in mind thar you need to connect as per the picture...
-
Page 15: Operation
3 Operation Operation The information presented in this section is intended as reference only. It is not possible to provide complete instructions for every possible boat and motor combination. Proper mounting depends in part on experience and the specific boat and motor combination. ·Overpowering a boat could cause severe 1. - Page 16 ·Check that the idle hole stays high enough to keep out water getting inside engine even if the boat is in stationary with maximum load. ·Incorrect motor height or obstructions to the smooth flow of water (such as the design or condition of the boat, or accessories such as transom ladders or depth finder transducers) can create airborne water spray while the boat is cruising.
-
Page 17: Maintenance
4 Maintenance Clamp screw mounting models ·Do not place the outboard motor on its side When transporting or storing the outboard before the cooling water has drained from it motor while removed from a boat, keep the completely, otherwise water may enter the cylinder outboard motor in the attitude shown. -
Page 18: Periodic Maintenance
Cleaning the outboard motor After use, wash the exterior of the outboard motor with fresh water. Flush the cooling system with fresh water. 1. Water surface 2. Lowest water level 5. Cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. -
Page 19: Removing Propeller
Golden Motor recommends that you do 2. Install the spacer (if equipped), thrust this service twice as often as specified in the washer, washer (if equipped), and propeller maintenance chart. - Page 20 3. Install the spacer (if equipped) and the washer. Tighten the propeller nut to the specified torque. Propeller nut tightening torque: 17.0 Nm (1.73 kgf-m, 12.5 ft-lb) 4. Align the propeller nut with the propeller shaft hole. Insert a new cotter pin in the hole and bend the cotter pin ends.
-
Page 21: Return And Repairs
Contact us before you make a return. Motor Authorized Dealers. (If you need local Goods must be returned within 7 days of receipt. repair and a Golden Motor dealer is not Goods must be in original packaging. nearby, contact us for assistance in Goods must not be fitted or used. - Page 22 Unauthorized changes/modification or tampering with any part of this product, or operation in any way other than as detailed in this User Manual, will render manufacturer’s warranty void. Golden Motor Technology Co.,Ltd www.goldenmotor.com sales@goldenmotor.com Mobile:86 519 81004118...
Need help?
Do you have a question about the EPO-03HP and is the answer not in the manual?
Questions and answers