Advertisement
Quick Links
Advertisement
Summary of Contents for ccpix H series
- Page 1 Manual H Series Digital video recorder 4 channel D1 H264 DVR Models: H401 H402 H411...
- Page 2 Note: DVR can run and monitor normally without a hard disk, but will not record and playback. 1.2 Mouse Connection The H series has two USB ports on the back panel for mouse and flash drive. 2 Turning on Plug the lead into the rear of the DVR and connect power supply to the mains, then switch on the plug socket.
- Page 3 4 Login When the DVR boots up, the user must login and the system provides the corresponding functions with the user preview. There are two user settings which are admin, and guest; and by default they have no passwords set. “Admin” is the super user; “Guest” for other users. Password protection: If the password is entered incorrectly three times, the alarm will sound.
- Page 4 6 Recording Configuration Set the recording parameters in the surveillance channel. You can enter [Main Menu]> [Record]> [Record Config] to set. The system’s default set is for 24 hours continuous recording. Picture2 Record Config 【Channel】Choose the corresponding channel number to set the channel.
- Page 5 regular： Perform the regular recording in the set time section. The video file type is “R”. detect：Trigger the “motion detect”, “camera mask” or “video loss” signal. The video file type is “M”. 7 Video Playback There are two methods to play the video files on the hard disk. 1.
- Page 6 Table2 Playback control key Note: Frame by frame playback is only performed in the "pause" playback state. Special functions: Exact playback: Input time (h/m/s) in the time column and then click playback. Local zoom: When the system is in single-window full-screen playback mode, you can drag your mouse in the screen to select a section and then left click mouse to zoom.
- Page 7 Picture5 Network Setup Network setup through Main Menu>System>Network 【IP address】Set the IP address. The default is: 192.168.1.10. 【Subnet Mask】Set the subnet mask code. The default is: 255.255.255.0. 【Gateway】Set the default gateway. The default is: 192.168.1.1. Ensure the equipment’s IP address and the router are in the same network segment.
- Page 8 Step2. Choose one channel and adjust sensitivity level, then set the time period of alarm surveillance. Set the monitor area (click the “set” button, choose the areas you want, a“default” chooses all areas, then right click to choose "up window". Step3.
- Page 9 Picture 7 CMS Interface 2.2 WEB After connecting to the network, enter the IP address of your DVR in Internet Explorer. For example, the IP address of the equipment is 10.6.0.114, and then you should enter http://10.6.0.114 on the address bar to connect. Step1.
- Page 10 Picture 8 Web Login Interface Step3. Login. Enter user name and password, the default Administrator User ID is admin, and the password is admin. The user should change the administrator password after loging in. (If you choose "Local Area Network", it's Main streams, if "wide Area Network", it's Sub streams.) You will see as follows interface after logging in.
- Page 11 Picture 9 WEB operation interface 3. Basic Web Operation 1) Screen Split Choose image preview mode; 2) Playback Enter playback mode, which supports multi-channel play back simultaneously. 3) Log Display log information； 4) Local Config Alarm and System setting 5) Channel operation Open the videos.
- Page 12 Picture 10 Encode setup 1.1 Encode setup for every channel Note: Only part of DVR mode support resolution switch. Step1. Local operation through 【Main Menu】>【System】> 【Encode】 （remote setup click right mouse and choose “config” in 【System】>【Encode】 ）. Step2. Choose channel 1, set the resolution as D1 (25fps, 1536Kb/s) Step3.
- Page 13 1.2 Extra Stream Setup Extra stream is used for remote client monitor and mobile monitor area. Step1. Enable extra stream Step2. Set frame rate and bit rates,operation way is the same as main stream. 2 Multi-channel Playback Simultaneously 4 channel DVR can support 4 channel playback simultaneously Picture11 Video Playback Step1.
- Page 14 Picture12 CMS Interface Step1. Enable extra streams(MainMenu->System->Encode) Step2. Open CMS, and then login. Step3.After add devices,rightclick device name to select "Connect all video(Main stream)" 4 Mobile Monitoring Smartphone viewing Step1. DVR config, go to MainMenu->System->Encode-> Extra Stream, enable it. Step2. Setup mobile monitor, go to MainMenu->System-> NetService->Mobile Monitor, choose "Enable"...
- Page 15 Picture13 mobile client software Interface Step5.Mobile setup. Click "setting" button at the right corner, then go to below picture 15. picture 14 mobile client software setting User name: login name of DVR Password: password of DVR Server: IP address or domain name of DVR Port: mobile monitor port of DVR, pls refer to Step 2.
-
Page 16: Appendix 1. Remote Controller Operation
MEYE_SB_S60_3rd.sisx Symbian S60 the 5th operation system mobile monitoring client software: MEYE_SB_S60_5th.sisx Android mobile monitoring client software:MEYE_Android.cab Blackberry mobile monitoring client software:MEYE_RIM.cod Iphone mobile monitoring software: use the app store to search "vMeye" and install it online. File download Using U disk and movable hard disk download to a local device, DVR supports the chosen file are high-speed backup to the storage devices. -
Page 17: Appendix 2.Mouse Operation
Serial number Name Function Multi-channels Multi-channels preview button Number button Password input/number input/ channel switch 【Esc】 Back to up window Direction button Direction and OK button Playback operate Playback Basic operation Record control Enter into record menu Remote Input the number of DVR to controller control it Assistant function... - Page 18 double click again resume multi-channel display Left click Choose according option in the menu Pop desktop shortcut menu in preview state Right click Current shortcut menu in the menu Add or subtract number value in the number setting Wheel button Switch the items in the combo box Page up or down in the list Choose the widget or move the item in the...