Page 3
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 12. For added protection for this monitor during a lightning storm, 2. Save these instructions for later use. or when it is left unattended and unused for long periods of time, 3. Unplug this monitor from the unplug it from the wall outlet.
Page 4
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a NOTE : Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
INTRODUCTION INTRODUCTION This manual explains how to correctly install, operate and get the best performance from your CCTV. Please read this user’s guide carefully before installing your CCTV, then keep it near your CCTV for quick reference. First, please check that the contents of the box corresponds with the following checklist : TFT LCD CCTV •...
PRODUCT FEATURES The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. The CCTV complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless.
SETUP SETUP CONNECTION CAM2 CAM1 S-VIDEO DC 24V HDMI 1.DC 24V IN 4pin Din Jack 2. Head Phone Out 3. PC Stereo Input 4. HDMI HDMI signal input 5. VGA RGB signal input 6. DVI DVI-D signal input 7. CAM2 R/L Audio signal input left and right for CAM2 8.
REMOTE CONTROL REMOTE CONTROL R1 POWER Turns the set on from stand-by or off to Stand-by mode. R2 INPUT SOURCE Select the signal source from the multiple input sources. R3 MUTE Turns the sound on and off R4 NUMBER Button Not used.
Page 10
R13 OK R23 ZOOM Select menu items. Select the screen format (CAM/HDMI mode only) R15 VOL +/- R24 SIZE Adjust the sound level Select the size of PIP display. R16 PR +/- R25 SKIP Not used. Not used. R18 PC R26 PIP Directly select pc mode R19 S MODE...
OPERA TION & ADJUSTMENT OPERA TION & ADJUSTMENT CONTROL PANEL 1 POWER INDICATOR The power indicator is Primary Function : Choose located on the front of the automatically the proper CCTV horizontal Position and vertical position & size of the screen IR SENSOR WINDOW image.(VGA MODE ONLY) Secondary Function : Allows for...
Page 12
KEY PROCESS ① To select OSD press the MENU button. ② Use LEFT-RIGHT button to select the menu. ③ Use DOWN button to select the sub menus. ④ Press SOURCE button, then using LEFT-RIGHT buttons you can make adjustments as necessary ⑤...
Page 13
ADJUSTMENT PROCEDURE <VGA MODE> Perform the Auto tracking Is the H.SIZE proper? Adjust the control. CLOCK Perform the H-POSITION. Is the noise displayed on the screen? Adjust the until PHASE the screen is cleared. Is the noise displayed on the screen yet? English - 8...
OSD FUNCTION VGA MENU (VGA/HDMI/DVI) P I C T U R E 1. Contrast Adjust the contrast of image, the difference between light and dark areas on the screen. 2. Brightness Adjust the brightness of image. 3. Color Mode Choose different preset color temperatures or set your own customized color parameters.
Page 15
G E O M E T R Y 1. H-Position Adjust the position of the display horizontally (left or right). 2. V-Position Adjust the position of the display vertically (up or down). 3. Clock Adjust the width (horizontal size) of the Screen image.
Page 16
P I P 1. Multi Window Activate or cancel the PIP function. 2. Sub Source Select the input source the PIP screen. (CAM1/CAM2/SVIDEO) 3. Size Select the PIP display size. (Small/Middle/Large/Double 1/Double 2) 4. Position Adjust the PIP display position. (R-Up/R-Down/L-Down/L-Up) 5.
Page 17
CAM MENU (CAM1/CAM2/S-VIDEO) P I C T U R E 1. Contrast Adjust the contrast of image, the difference between light and dark areas on the screen. 2. Brightness Adjust the brightness of image. 3. Tint Adjust the Tint of image. 4.
Page 18
F U N C T I O N 1. 3D NR. Reduce the noise in the picture due to poor reception or poor picture quality. (OFF/LOW/MIDDLE/HIGH) 2. MADi Generation advanced color engine automatic picture enhancement gives. (2D/3D) 3. H-Size Adjust the width (horizontal size) of the Screen image.
Page 19
P I P 1. Multi Window Activate or cancel the PIP function. 2. Sub Source Select the input source the PIP screen. (VGA/HDMI/DVI) 3. Size Select the PIP display size (SMALL/MIDDLE/LARGE/DOUBLE 1/DOUBLE 2) 4. Position Adjust the PIP display position. (R-UP/R-DOWN/L-DOWN/L-UP) 5.
Page 20
PIP TABLE MAIN HDMI CAM1 CAM2 S-VIDEO HDMI CAM1 CAM2 S-VIDEO : Supported X : Non Supported English - 15...
Page 21
SELF DIAGNOSIS If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the CCTV screen is No Signal, Out of range or None support. No Signal screen is displayed when the D- Sub signal connector is connected but the status of the CCTV is on DPMS mode.
TROUBLESHOOTING TROUBLESHOOTING Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card.
Page 24
Symptom Low sound. Adjust the volume on the OSD Menu. Adjust the volume of the sound card in the computer. VIDEO screen Check if VIDEO mode has been set. cannot be seen. Check if the video terminal is properly connected. No video.