1) Package Content and Views of G07......................................................................................................................2
2) Installing Mounting for G07 .................................................................................................................................3
3) Powering On G07..................................................................................................................................................4
4) Connecting G07 to the Network...........................................................................................................................5
G07 User Manual Congratulations for choosing a world-class Total Solution with Controller Gateway using ZigBee, Ethernet, and Wi-Fi wireless transmission technology. This manual is designed to help set up and get the most from the sensor in a few short minutes.
(if not using wall plugs) Size 1 Phillips screwdriver a) Locate G07 with at least 15cm (approx.. 6 inches) spacing on each side (except on mounting side) avoiding the following sources of interference: direct sunlight, air flow from vents, fans, doors, windows, heaters, sources of steam, oil vapor, etc.
Connect DC 12V adapter and plug into power socket. b) G07 will take about 1-2 minute(s) to boot up. During the booting process, the NETWORK and ALERT LEDs may both flash for about 2 seconds and light on for about 10 seconds.
Computer (running Windows) Repeater or Ethernet switch (supporting DHCP connection mode) with internet connection and an available Ethernet LAN port reserved for G07 NOTE: If you want to use Wi-Fi connection, please use a Wi-Fi repeater with several available Ethernet LAN ports, or you can include a Wi-Fi repeater or access point within the same local network hosting both your computer and your G07.
Page 6
Use an Ethernet cable to connect G07 to the same repeater or Ethernet switch that your computer is connected to, or you can use an Ethernet cable to connect G07 to a repeater or Ethernet switch that belong to the same local area network (with internet connection) of your computer.
G07 User Manual NOTE: Your G07 may take about 1-2 minutes to boot. If you cannot find your gateway in Gateway Finder, you may wait for your G07 to finish booting and search again. h) When the login page appears, enter the username and password (default username and password are both ‘admin’), then click Login to enter the G07 Web Setting Homepage.
Page 8
This category sets G07’s local and internet network options. G07 provides Ethernet, Wi-Fi, and 3G options to connect to a computer or to the cloud. When G07 is powered on or rebooted, it will first search Ethernet for network connections. If no network connection exists on the Ethernet, G07 will then sequentially search Wi-Fi and 3G for network connections.
Page 9
DHCP (we recommend you to choose DHCP). Cloud Server Setting: Sets parameters required for your G07’s cloud connection. o IP : The default IP address is that of Nietzsche Sentrol Cloud server, 119.163.1.159. If you want to connect to another cloud server, you can change the IP address to that of another cloud server.
Page 10
Please select or enter information provided by your 3G network service provider. Date/Time: Time Setting: Set up your G07’s System Time and Time Zone settings by configuring the following parameters: NTPD Service: Enables or disables NTPD (Network Time Protocol Daemon, a service that automatically synchronizes G07’s current date and time settings periodically) (Enable /...
Page 11
If NTPD is enabled, specify NTP Server and Update Interval. NTP Server: Specify the NTP Server’s IP address (default is 118.163.1.157). Update Interval: Specify the time interval after which your G07 will update time with the NTP server (default is every 24 hours).
Page 12
Reset button to reboot G07 with the upgraded firmware. Reboot: Click Reboot to restart your G07, as this action is required for any changes made in this web setting homepage to be effective (unless stated otherwise). ZigBee Status : ...
6 Sentrol Cloud Gateway Register a) Go to http://www.sentrolcloud.com/nhr/view/front/newgateway.php b) Enter the last 8 digits of G07’s MAC address in the space below “Gateway Mac”. c) Enter the CAPTCHA code according to the page as shown below. d) Click Continue button to proceed to the next page.
G07 User Manual 7 Replacing G07 in Existing IoT Network a) Login to Sentrol Cloud with your Sentrol Cloud account: http://www.sentrolcloud.com . b) Select Administration Gateway. c) Find the old gateway to be replaced and click that gateway’s corresponding Replace button.
Apply 1 quick press to the Join button on G07, the green LED will flash once every 3 seconds for up to 60 seconds to indicate the Permit Join status, allowing other devices to join to its IoT (Internet of Things) network.
Sharp-pointed instrument a) Network Reset: In the case where the G07 is no longer connected to the cloud, G07 will need to be reset by applying a 10-second press to the Reset button (with a sharp-pointed instrument) until both the Network LED and Wireless LED flash 3 times together.
Page 17
Built-in 1G memory card when connection to Cloud is lost End Device NHR HA Devices Enabling Devices Repeater S05-R / WZB-01USBR / WZB-02485R Interoperability Sentrol Cloud Thank you for choosing NHR’s G07 Gateway. We are looking forward to working with you!