Advertisement
/
Dust Indicator
\
.
Telescopic Pipe
\
The telescopic
suction
pipe can be
adjusted
in length for the operator
convenience.
After each adjustment
turn
the
ring
as illustrated
and
tighten it securely.
{
Remote Power Control Switch
\
(
Power Control Indicator
=
-r
I
The
degree
of dust suction
power
can be changed by sliding the lever.
slide
the
lever
to an appropriate
position
depending
on the cleaning
needs.
Use only
the
hose with
Remote
Power
Control
Switch
for
this
cleaner.
If
used with
other
cleaners,
the
hose can M a cause of damage to
them.
I
Tfw Power Control indicator
show
The dust indicator
shows when
the
du$t compartment
is full.
When
the dust indicator
has turned
from green to red, empty the dust.
Empty the dust when the red indicator
lights up
P0wt3a
CONTROL
the suction power of the cleaner.
DUSTINDICATOR
(Ql '/
Adju~ing
ring
L
J
SOFA
I
BARE FLOOR
RUG (Low Pile)
{When checking the dust)
Push the POW6T control lever to the
'aMAX." position.
Ltft the turbocleen off the flcxx.
Remwe the crevice tool.
red marker line.
\
I
/
Turboclean
7
/
.
f-
Hoae StoPPer
1
/
Handy Attachment
Compartment
Y
I
The
two-way
turboclean
has a lever
with two positions.
Insert
the hose all the
way
up
to
the
hose
stopper.
To detach it, press the
hose stopper
and pull
The
compartment
stores a dusting
brush
and a
crevice tool, a quick selection for all your cleaning
needs.
Crevica tool
\
Dusting br.d
F
The tilting
angle of the dusting brush neck IS adpJst-
Attach
the dusting
brush to the end of the hose or
k
Use to clean the curtain,
window frames, lamp shades,
I
Note:
Do not clean bare floors with
lever position "RUG".
This might damage the floor.
DUST DISPOSAL
Turn the motor off, pull the hose out of the unit and empty
out the dirt as follows:
A
severely
soiled
or clogged
filter
Note
&
should
be thoroughly
washed
with
Never
insert the cloth
fresh tepid water.
A neutral detergent
filter
into the body of
could be used if required.
o
the
unit
unless it
is
1. Washing
completely
dry.
2, Orying
;
[;...:.
Never
wash
the filter
with
boiling
water
or
1. Open the dust compartment
cover
by pushing the clamp button.
2. Take out the filter frame.
+$iii2
Clamp button
-.
%
0"
Cloth fil{
~-
expose
it to an open
flame to dry.
CARE OF THE SECONDARY
FILTER
3. Open the fastener of the filter
and
4. Close the fastener completely,
than
put the filter frame.
If suction does not get stronger,
even after the dirt is emptied
out and the cloth filter
properly
cared for, pull out the plug and clean the secondary
filter.
empty out the dirt.
Fastener
1. Pull the
knob
with
the finger
tip
2. Take
out
the secondary
filter
and
and remove the filter cover.
wash with water.
K
Filter cover
*
er cover
secondary
filter
5. Close the dust compartment
cover.
Attaching and removing filtar
After removing the hook, the filter can
be removed from the filter frame.
When
attaching
the filter,
first
insert
the
lower
part
of the
filter
into the
groove and snap in place.
3. Shake
off
excess
water
and
dry
4. Put
the
secondary
filter
back
in
thoroughly.
place in the filter
cover and set as
shown in the sketch.
Sat
t he these positions
–;#–
m
Hook
Groove
Advertisement
