Summary of Contents for Cartadis CM4000
- Page 1 Cartadis CM4000 Multi-Coin Operated Copy Vending Unit User's and technical Manual V5.0...
- Page 2 Cartadis CM4000 Multi-Coin Operated Copy Vending Unit User's and technical Manual V5.0 Cartadis is a trade mark of C.M.F. tel: (33) 1 48 77 40 60 -...
- Page 3 User's Manual V5.0 - Cartadis CM4000 ! SAFETY # ! Intervention This CMF product and supplies Any installation, removing or are manufactured and certified to intervention on the Cartadis unit strict safety regulations, require previously to unplug the electromagnetic regulations and copier or the multifunction.
-
Page 4: Table Of Contents
TABLE OF CONTENTS SECTION PAGES USER'S MANUAL INTRODUCTION ..............CM4000 and THE END USERS ..........CM4000 and THE OPERATOR ..........3.1. Menu organization ............ 3.2. Statistics ..............3.3. Price setup ..............3.4. Discount price setup ..........3.5. Stactistics printing ............. - Page 5 User's Manual V5.0 - Cartadis CM4000...
-
Page 6: Introduction
INTRODUCTION Thank you for your choosing a Cartadis CM4000 to manage your copy vending. This unit is dedicated to copy vending and thus shall be attached to a photocopier of any brand. It vends photocopies in an unattended environment against coins, the main features... - Page 7 - a portable printer allows the statistics to be printed out. The Cartadis CM4000 is available for almost all the countries, in case new coins are issued, the unit can be upgraded at the factory or at your local Cartadis distributor.
-
Page 8: Cm4000 And The End Users
CM4000 and THE END USERS Cartadis CM4000 shows it is ready for work by displaying: Picture 1 Number of copies available Shows the paper size selected The left side of the display shows the type of the copy selected, 4 types are available: F1, F2, F3 and F4. - Page 9 If the copier can print copies in different sizes or colours but does'nt supply status signals then it will not be possible to manage them differently at the CM4000 level. To know your configuration ask the technician who made the installation on your copier.
-
Page 10: Cm4000 And The Operator
In the same way to leave the menu and switch back the CM4000 to user mode you have to remove the lockable free key copy. Within the software menu three keys allow the operator to move from one function to an other or to enter values. - Page 11 User's Manual V5.0 - Cartadis CM4000 The meaning of keys within the menu is: Enter in a submenu or move the cursor to the right. Move to the next menu item or modify the blinking digit. Leave the current menu or move the cursor to the left.
- Page 12 CM4000 and the Operator Cash Stat turnover nbr.F1 Number of F1 format copies nbr.F2 Number of F2 format copies nbr.F3 Number of F3 format copies nbr.F4 Number of F4 format copies Fre.F1 Free F1 format copies Fre.F2 Free F2 format copies Fre.F3...
- Page 13 • User's Manual V5.0 - Cartadis CM4000 bonus Pr b1 Price for Bonus 1 (F1 format) Nbr.b1 Number of copies for Bonus 1 Pr b2 Price for Bonus 2 (F1 format) Nbr.b2 Number of copies for Bonus 2 Deci Decimal mode...
-
Page 14: Statistics
CM4000 and the Operator 3.2 Statistics The Cartadis CM4000 keeps in its memory 9 counters related to the copies made. These counters are not resetable and so are always relative to the date of installation. Since only 5 digits can be displayed at the same time, some counters are displayed in two stages as shown in the following example. -
Page 15: Price Setup
User's Manual V5.0 - Cartadis CM4000 3.3. Price setup The Cartadis CM4000 can manage 4 formats (or types) of copies, each format being sold at a different price: Pr.F1,Pr.F2, Pr.F3 and Pr.F4. In most of cases Pr.F1 is the price of an A4 copy format. -
Page 16: Discount Price Setup
In most cases Pr.F2 corresponds to an A3 copy format. 3.4. Discount price setup The Cartadis CM4000 allows to set up 2 levels of discount prices for the format F1. These prices are entered in a price table: Number of copies... -
Page 17: Stactistics Printing
The discount price is given to the user only if copies are not made in between the coins insertion. A discount price is computed by the CM4000 for the F2 to F4 format copies. This computation is based on the ratio F1 Price to the selected format price. - Page 18 CM4000 and the Operator Print out example: CM4000 software version CA400 V1.6 # 8740 ------------------------- CM4000 serial number SERIAL coins recognition EURO V1.2 identification table - Statististics - CASH 2 561.55 NBR.F1 9 365 NBR.F2 1 756 NBR.F3 NBR.F4 FRE.F1 FRE.F2...
-
Page 19: Free Copies
: RTS/CST 0 Volt 3.6. Free copies The CM4000 is fitted with a lock on the top panel, the two possible positions of the key are: unlocked position, the key can be removed and coins have to be inserted to make copies. -
Page 20: Installation
CM4000 pedestal. Four holes on the back side of the Cartadis CM4000 allow to screw it on the copier. 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7... -
Page 21: Electrical Connection
"seen" by the photocopier as a key counter and has therefore to be connected like a key counter. The CM4000 has no power pack of its own, it is usually supplied from the +24V power supply of the photocopier. The photocopier can supply the +24V to... - Page 22 Ambre To modify the default position of the jumpers you must remove the black plastic coin selector from inside the CM4000 housing. The electronic board is on the back side of the coin selector. To locate the jumpers on the CM4000 electronic board see next page.
-
Page 23: Connection For Only One Paper Format Management
Then this power supply has to be connected to the CM4000 internal screw connector (old model) or to the JACK connetor and the switch SW1 has to be moved upward. -
Page 24: Connection For Several Paper Format Management
- Yellow/Green wire = copier frame 4.2.2 Connection for several paper format management The CM4000 can manage up to 4 formats called "F1", "F2", "F3" and "F4"; each one having its own copy price. F1 to F4 are usually dealing with paper formats or Black and White or colour copies. - Page 25 "StateB" and "StateC" inputs cause the user's credit to be deducted with respectively P2 and P3 prices. The 2 following tables describe in details the CM4000 behaviour for each of the 2 possible values of the "mode" parameter. "mode = 0" parameter (default factory setting) The "StateB"...
- Page 26 As the Black wire and the Brown wire are usually connected in parallel to the start clutch for A3 format paper. In this mode, the CM4000 is not able to know, before the copy is made, which copy format is selected on the copier. So the CM4000 "relay 1" will be ON as soon as the F1 copy credit is different from 0 and will stay ON whatever the selected format on the copier.
-
Page 27: Configuration Parameters
- if this parameter is set too high, CM4000 may disregard count down pulses. - if this parameter is set too low, CM4000 will count more copies than were made. Adjusting it to 20 milliseconds gives generally good results (default setting). -
Page 28: Relay 1 Or 2 Opening Delay
CM4000 will never cancel the remaining credit. - If "rest cleared" parameter = ON, the CM4000 will clear the remaining credit in case it is lower than the smallest price. € Example: if "rest cleared" parameter = ON and copy price is 0.15 €... -
Page 29: Accepted Coins Selection
This value is printed on the statistics print out and so, allows to identify the origin of the copier when several print out are coming from several CM4000. You can enter the value you want for the Serial number. The default factory setting is €... -
Page 30: Installation Validation Procedure
Installation 4.4 Installation validation procedure To check the CM4000 for correct operation, follow the procedure: insert at least one coin of each type to check for acceptance and rejection according to the parameter "coin" (see page 26). Check the money credit after... - Page 31 Technical User's Manual V5.0 - Cartadis CM4000...
-
Page 32: Trouble-Shooting
Err 1 or Err 4 The CM4000 is out of order and the coin mechanism has to be replaced. Err 2 The statistics memory is corrupted, ask to your local dealer, he will give you the procedure to clear this error. - Page 33 Technical User's Manual V5.0 - Cartadis CM4000 Coins are often rejected Clean the coin desk: - open the CM4000 door, - open the selector door, you have to remove the top plastic part by unscrewing the black screw, - clean the inner parts corresponding to the coin desk, - rescrew the top plastic part.
-
Page 34: Technical Specifications
TECHNICAL SPECIFICATIONS TYPE CM4000 FUNCTION Multi-coin operated copy vending unit ELECTRONICS Very large scale integrated 32 bits microcontroller MEMORY EEPROM for parameters and statistics backup OPERATING CONDITIONS Moisture 20% - 90% RH Temperature 10 - 40°C Indoors only DIMENSIONS 280mm (W) x 380mm (H) x 100mm (D) WEIGHT 7.5 kg (empty) - Page 35 Technical User's Manual V5.0 - Cartadis CM4000 COUNTER CAPACITIES User copy credit not limited User money credit max 1 000.00 Statistics: Turnover Max 99 999,00 (overflow round up to 0) Format 1 Max 9 999 999 (overflow round up to 0)
Need help?
Do you have a question about the CM4000 and is the answer not in the manual?
Questions and answers