Do you have a question about the PH-LW15-BLP/17A and is the answer not in the manual?
Questions and answers
Summary of Contents for Sunrise PH-LW15-BLP/17A
Page 1
SUNRISE CHILLING PRODUCT SERIES LASER CHILLE RS P H - L W 1 5 - B L P / 1 7 A Shenzhen Sunrise Industrial Co.Ltd. Add.: No.4,the 4th Tengfeng Road ,th e 3 Industry Zone Fenghuang,Fuyong,Baoan District,Shenzhen,China. P.C.: 518103...
Page 3
Notes Table of Content General Information----------------------------1 1.1 To User 1.2 Unpacking - General Introduction---------------------------2 2.1 Content SUNRISE 2.2 Product Summary 2.3 Technical parameter 2.4 Dimensions 3. - Installation and Start up------------------------6 3.1 Safety notice 3.2 Installation location requirements 3.3 Power 3.4 System connection...
Page 4
LASER CHILLER OPERATORS MANUAL Notes Notes 1 - General information 1.1 To user Thank you for choosing SUNRISE laser chiller. Please read the manual thoroughly before operating the machine. SUNRISE Please keep your manual, receipt, QC pass and warranty card for further use.
6.Equipped with high and low temperature alarm signals output,it can be normal open or normal close signal as options. 7.Use digial temperature controller which is designed by sunrise and produced by famous oem manufacturer. One button operation, the machine runs by memory...
Page 7
LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL 2.3 Technical Specifications 7 - Maintenance and technical support Model PH-LW15-BLP/17A 7.1 Circuit Diagram 1500 cooling Btu/h 5120 capacity 1290 Kcal/h Power supply 1PH-220V/50Hz or 60HZ refrigerant R134a...
Page 8
Please check whether the voltage is too high or too low Please check whether the air discharge side has been blocked Please check ambient temp., high ambient temp. will make the compressor halt for a short time. Note: No filter Dimensions W(mm) L(mm) H(mm) Model PH-LW15-BLP/17A...
Page 9
LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL Solution for no error codes display 3 - Installation and start up Ⅰ.Insufficiency cooling: ① Please check whether the condenser radiator and air filter is dirty ② Whether the temp. of the installation site is too high and ventilation condition is bad 3.1 Safety Notes ③...
Page 10
LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL System function view Warning: please cut off the power before installation!! cooling only (bypass) 4.2.6 startup option, press up and down button to choose "yes" or "no" 3.2 Site requirements: Ambient temperature and relative humidity (RH) Startup mode Our chiller suitable for install indoors, ambient temp.
Page 11
LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL LASER CHILLER OPERATORS MANUAL Connecting of water bypass and accessaries for water circulation. System standby (default value:20℃ ) water tank temp: xx℃ setting temp: xx℃ (default value:0.1℃) Temp differential: xx℃ 4. Press set button to enter function option, chosen option flashes, press set button to enter next level setting.
Page 12
Warning: erosive and inflammable liquid is not allowed!!! 1. System on when power connects, initial interface show for 1.5sec. Thank you for using Sunrise water chiller, system is starting up, Warning: Anti-freezing liquid is necessary for operation under 8℃ please waiting 2.
Need help?
Do you have a question about the PH-LW15-BLP/17A and is the answer not in the manual?
Questions and answers