OWNERS INFORMATION COX MODEL NO: _________________________________ COX INVENTORY CODE NO: ________________________ COX SERIAL NO:_______________________ Located on Label inside Transmission Housing B&S ENGINE MODEL NO:______________TYPE:____________ CODE:_______________ Located on Engine refer Engine Owners Manual HONDA ENGINE MODEL NO:____________SERIAL NO:_______________ Located on Engine refer Engine Owners Manual DATE OF PURCHASE:__________________________________ OWNERS NAME: ADDRESS:...
SAFETY INSTRUCTIONS Read, understand, & follow all instructions in the Never mow while barefoot or wearing open sandals Owner/Operators manual. or thongs. Wear long trousers and heavy shoes. Know the controls and how to stop the engine ...
Page 4
A16314E PRE-DELIVERY INSTRUCTIONS INTRODUCTION: Install the two seat springs using the screws, washers, nuts, to the transmission cover, and tighten the screws, washers, The purpose of this procedure is to ensure the dealer/ and nuts. distributor has assembled & made the necessary checks, & adjustments, before mower...
Page 5
ITEM PART NO DESCRIPTION A163064R Cover, Transmission, Red NM8NT Nut, Hex, Nyloc, Thin, M 8,Pc6,Znpl SH0820M Screw ,Hex, M 8x 20,Pc8.8,Znpl W051218 Washer, Flat, 5/16"X3/4"X18g,Znpl Sub Assembled Seat SH0825M Screw, Hex ,M 8x 25,Pc8.8,Znpl A163060 Spring, Conical, Seat, Heavy W05m202 Washer, Flat 5/16"X3/4"X14g SW13 Wheel,Steering,13",W/ Cover...
OPERATING INSTRUCTIONS IMPORTANT For safety it is advisable at all times, other than when mowing, that the mowing attachment be kept in the RECOMMENDED FUEL disengaged position. Unleaded fuel is recommended by all manufacturers of engines TO DRIVE FORWARD/REVERSE: fitted to Cox products. Engine speed is regulated by the engine speed control, set DRIVE PRESSURE engine speed control to desired engine power.
MAINTENANCE INSTRUCTIONS It is the owner’s responsibility to ensure that all-periodical 9. CUTTER DISENGAGING ADJUSTMENT: With the engine switched checks, necessary adjustments, services and repairs are off, engage the mowing attachment, then fully lower. Place a straight carried out. edge vertically against the front of the front axle beam and in line with the disengagement lever.
MAINTENANCE SCHEDULE BEFORE EACH USE BEFORE EACH USE BEFORE EACH USE Check engine oil level, adjust if required Check for loose fasteners, tighten if required Check engine air cleaner foam pre-cleaner, service if required Lubricate stub axles Check engine rotating screen/finger guard, clean if required Lubricate Drive Chain Check operation of safety switches, service if required Check mowing attachment cutter blades, bolts, nuts, disc/s,...
Page 9
9 MONTHS OR 75 HOURS WHICH EVER OCCURS F 9 MONTHS OR 75 HOURS WHICH EVER OCCURS F 9 MONTHS OR 75 HOURS WHICH EVER OCCURS FIRST IRST IRST Change engine oil if operating under heavy load or high ambient Check for loose fasteners, tighten if required temperature Check battery condition, service if required...
Page 10
21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST 21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST 21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST Change engine oil if operating under heavy load or high ambient Check mowing attachment cutter blades, bolts, nuts, disc/s, housing , temperature and guards for wear or damage, replace if required Check engine air cleaner foam pre-cleaner, service if required *...
Page 11
33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST 33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST 33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST Change engine oil if operating under heavy load or high ambient Check mowing attachment cutter blades, bolts, nuts, disc/s, hous- temperature ing , and guards for wear or damage, replace if required Check engine air cleaner foam pre-cleaner, service if required *...