Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Zhejiang IPC2122SR3PF36
Summary of Contents for Zhejiang IPC2122SR3PF36
- Page 1 Network Bullet Cameras Quick Guide Manual Version: V1.01...
- Page 2 Trademark Acknowledgement and other Uniview’s trademarks and logos are the property of Zhejiang Uniview Technologies Co., Ltd. Other trademarks, company names and product names contained in this manual are the property of their respective owners.
- Page 3 Disclaimer The default password is used for your first login. To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). To the maximum extent permitted by ...
- Page 4 change without prior notice. Update will be added to the new version of this manual. Use of this manual and product and the subsequent result shall be entirely on your own responsibility. In no event shall we be reliable to you for any special, consequential, incidental, or indirect damages, including, among others, damages for loss of business profits, business interruption, or loss of data...
- Page 5 for any consequences resulting from illegal operations of the device. The illustrations in this manual are for reference only and may vary depending on the version or model. As a result, some of the examples and functions featured may differ from those displayed on your monitor.
- Page 6 proper storage, use and disposal of this product, national laws and regulations must be observed. Safety and Compliance Information Safety Symbols The symbols in the following table may be found on installation-related equipment. Be aware of the situations indicated and take necessary safety precautions during equipment installation and maintenance.
-
Page 7: Symbol Description
indicated by the symbols to avoid hazardous situations and use the product properly. Symbol Description WARNING! Indicates a hazardous situation which, if not avoided, could result in bodily injury or death. CAUTION! Indicates a situation which, if not avoided, could result in damage, data loss or malfunction to product. - Page 8 Installation This device is a class A product and may cause radio interference. Take measures if necessary. Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to ...
- Page 9 The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam. While shipping, the camera should be packed ...
- Page 10 Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface. Never look at the transmit laser while the power is on. Never look directly at the fiber ports and the fiber cable ends when they are powered on.
-
Page 11: Regulatory Compliance
Regulatory Compliance FCC Part 15 This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 12 1. This device cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. LVD/EMC Directive This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC.
- Page 13 WEEE Directive–2002/96/EC The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
-
Page 14: Table Of Contents
Contents 1 Packing List ............. 1 2 Appearance ............. 2 Dimensions and Appearance ............2 Cable Connection ................2 3 Mount Your Camera ........3 Wall Mount ..................3 Start Your Camera ................6 Waterproof Components for an RJ45 Plug ........7 Waterproof Tail Cable.............. - Page 15 Install the ActiveX ................13...
-
Page 16: Packing List
1 Packing List Item Quantity Camera User document Accessory pack Contact your local dealer if the package is damaged or incomplete. -
Page 17: Appearance
2 Appearance Dimensions and Appearance Φ4.5mm (0.18") 39mm (1.54") Cable Connection IP Network... -
Page 18: Mount Your Camera
Description Description RESET button Earth terminal Network Power interface interface For specifications, see the latest product datasheets. Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise. - Page 19 following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1 Locate the positions 2 Drill holes on the of the holes. wall. Paste installation positioning Use a Ø 6-6.5mm drill bit. stickers on the wall and align the cross center to the hole in the wall.
- Page 20 5 Mount your camera 6 Adjust the onto the wall and monitoring direction. connect all cables. Lead tapping screws through the guide holes in the base Adjust the opening of the and fix them on the wall by universal joints as required. using a screwdriver.
-
Page 21: Start Your Camera
The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall. If open installation is adopted, cables are not penetrated into the wall but threaded out from the outlet on one side of the base. -
Page 22: Waterproof Components For An Rj45 Plug
Waterproof Components for an RJ45 Plug 1 Attach the seal ring to 2 Mount the the waterproof waterproof connector. components. Insert in order Seal ring 3 Insert the cylindrical 4 Insert the cable into waterproof ring into the connector and bolt. -
Page 23: Waterproof Tail Cable
In step 2, you can crimp the inner wires of the cable with the RJ45 plug first and then cover the waterproof components. You may also cover the waterproof components first. Waterproof Tail Cable Connect the tail cables and then take the following steps to protect the tail cables from water using waterproof tapes. - Page 24 3 Protect other cables 4 Wrap all the tail using insulating cables together tapes. using insulating tapes. 5 Choose a start point 6 Protect the tail for waterproof tapes. cables using waterproof tapes. Waterproof tape...
-
Page 25: Set Your Camera Over The Lan
Avoid short circuit when insulating the cables. Use self adhesive waterproof tapes that will stick together with the twisted cables. Tighten waterproof tapes when wrapping the cables and make sure the cable connections are fully covered. You are recommended to put the waterproof ... - Page 26 Please contact your dealer to get the EZStation. Please refer to the user manual of EZStation for detailed information. 1. Connect your camera and your PC as shown in the figure below to ensure the routing is available. 2.
-
Page 27: Access Your Camera
The default IP address is “192.168.0.13”. The default username is “admin” and the default password is “123456”. To access your camera from a different subnet, set the gateway for your camera after you log in. 5 Access Your Camera Access Your Camera Before you begin, check that: Your camera is operating properly and... - Page 28 1. Open your browser, input the IP address of your camera (default IP is 192.168.0.13) in the address bar and then press Enter to open the login page. 2. Enter the username (default is “admin”) and password (default is “123456”) and then click Login.
- Page 29 1. Click Download. 2. Click Run to install the downloaded ActiveX. You may also click Save to download the file to your computer first. 3. Close the browser and follow the steps to complete the installation.
- Page 30 For your first login with Windows 7, if the system does not prompt you to install ActiveX, follow these steps to turn off UAC: click the Start button, and then click Control Panel. In the search box, type uac, and then click Change User Account Control Settings.
- Page 31 BOM: 3101C0C5...