Advertisement
Quick Links
I
N
S
T A
flipIT
Technical Support:
www.smartdesks.com
800-770-7042
Procedure for
these models:
FIK-19
•
FIH-19
•
FIK-23
•
FIH-23
•
1. Use included templates for cutting table top
and pilot holes; or
2. Start on page 8 to install flipIT® into a factory-cut
table top with pilot holes.
This manual is used for all flipIT®
monitor mount systems.
The difference in cut-out
width dimension has no impact
on the installation procedure.
The appropriate template is
included with your flipIT Kit
for 19 or 23 configuration.
ATTENTION:
The weight of the monitor counterbalances the force of the
pneumatic cylinder (gas spring).
It is advised to install the gas spring just before installing
the monitor. If the gas spring is installed without a monitor,
take care to control the lid by hand. The lid will open too
fast if the monitor is not installed.
©2015 CBT Supply, Inc. dba SMARTdesks®. All rights reserved. SMARTdesks and flipIT® are registered trademarks of CBT Supply, Inc.
L
L
A T
®
monitor mount system
I
O
N
Models FIK-19 and FIK-23 include a keyboard
tray which assists in opening the flipIT® lid.
Models FIH-19 and FIH-23 have no keyboard
tray, but include a PULL handle for opening.
M
A
N
U
US Patent No. 7,509,912
A
L
REV 08252015
Advertisement
Summary of Contents for FlipIT FIK-19
-
Page 1: Technical Support
Models FIH-19 and FIH-23 have no keyboard fast if the monitor is not installed. tray, but include a PULL handle for opening. ©2015 CBT Supply, Inc. dba SMARTdesks®. All rights reserved. SMARTdesks and flipIT® are registered trademarks of CBT Supply, Inc. REV 08252015... -
Page 2: Installation
Notes for easy disregard for power tool manufacturers’ safety precautions. installation Whenever possible, install the flipIT before assembling the desk. You will be installing from the top and the underside: sawhorses are recommended. If the desk is assembled, see if the desktop can be removed. -
Page 3: Parts And Hardware
Parts and Hardware 1.3.1 1.3.3 1.4.3 Item No. Qty. Part ID Description 31500 flipIT FIK|H-19 Desktop Assembly 31450 flipIT FIK|H-23 Desktop Assembly 31498 Grommet / Subassembly 31499 Top Lid 29784 LH Cable Arm Assembly 1.3.1 28473-LH LH Arm Catch Assembly 1.4.3... - Page 4 WOOD SCREW (21486) (8) #10-32 X 3/8 PH,PR,TRILOBE (TS295) (1) Paper template Provided appropriate for your flipIT Kit: Not used when installing into a factory made, flipIT Ready product. Cut-out placement is referenced from the center line of the user space. Make the cut-out top surface up.
- Page 5 Make cutout using template • Determine the center of the user space and mark this center line in pencil. • Fold template at user edge and align with • Table top surface up: tape the template in position, center line and front edge keeping the paper as flat as possible.
- Page 6 • Your corners should look like the above • Your perfectly cut table top should look like the one on the right • The flipIT collar has a trim flange that will hide any slight imperfections in the cut line and finish the installation technical support 800-770-7042 www.smartdesks.com...
- Page 7 Tray (FIK) or Pull Handle (FIH) • Turn the table top over to work on the underside • If you are installing the FIK-19 or FIK-23, use the same template used for making the top cut-out. • Align the template to the Center Line of the user side.
- Page 8 #10, 5/8” round head wood screws, a cable with eyelet end and a self-tapping metal screw— #10-32 x 3/8 PH, PR, Trilobe (TS295)— used to connect the flipIT lid to the assembly. • Position the assembly over the pilot holes...
- Page 9 Install the flipIT® into the Cut-Out (all models) • Hold the flipIT lid assembly by the • Align the flipIT lid to the cut-out • Span your grasp to avoid trim collar pinching your fingers and let the • Note: the corners are fragile until assembly drop into place •...
- Page 10 Cables should be attached loosely The cable on the flipIT cable arm assembly ships attached, but if it should need adjustment, do not overtighten the cable. It needs to work freely. Adjust it with a 3/8” open end wrench and #2 Phillips blade screwdriver.
- Page 11 S hook you can purchase at a hardware store to lengthen the cable. Cable ties will also work. Attach gas spring • The gas spring ships attached to the flipIT lid assembly • Pry off the locking hub on the free end with a flat blade screwdriver •...
- Page 12 The male half of the VESA mount is provided to fine-tune the balance If it is mounted too low, the opening attached to the flipIT lid with three of the opening performance. If the might be too fast (like jumping off a Euroscrews.