Download Print this page

Mirror Models C15A Lorry Assembly Instructions Manual

1/35 scale

Advertisement

Quick Links

CMP C15A Lorry Van Truck
Precision plastic model
MIRROR
Models
Ltd.
1/35
Scale
Kit No.
35101
The Canadian Military Pattern truck was a class of military truck made in large numbers
in Canada during World War II to British Army specifications for use
in the armies of the British Commonwealth allies. Standard designs were drawn up
just before the beginning of the war. CMP trucks were also sent to the Soviet
Union following the Nazi invasion of Russia, as part of Canada's lend-lease program
to the Allies. During the War CMP trucks saw service around the world in the
North African Campaign, the Allied invasion of Sicily, the Italian Campaign, t
he Russian Front, the Burma Campaign, the Battle of the Philippines (1941-42),
the liberation of Northwest Europe, and the Western Allied invasion of Germany.
CMP trucks also saw service in post-war conflicts in Indonesia, French Indochina,
and the Portuguese colonies in Africa. Most CMP trucks were manufactured by
the Chevrolet division of General Motors of Canada Ltd and by the Ford Motor
Company of Canada. Just over 400,000 CMP trucks were manufactured in Canada,
accounting for roughly half of the 815,729 military vehicles made in Canada
during World War II. Chevrolet-built CMP trucks had a 215 cu in (3.5 L),
85 bhp (63.4 kW) straight-6 overhead-valve engine. Cab design changed twice, first
designed at Ford, second and third cab designs - called No. 11, 12 and 13. First two
type were similar, the main difference being a two-part radiator grille in
No.12 cab, its upper part was opened with a bonnet, which was known as the "Alligator cab".
The production of CMP truck bodies in Canada was subcontracted
out to smaller companies in Ontario and Manitoba, organized into the wartime Steel
Body Manufacturers Association by the Department of Munitions and Supply.
The wide variety of truck body designs included general service, water tanker,
fuel tanker, vehicle recovery, dental clinic, mobile laundry, wireless house, machinery,
folding boat transport, and anti-tank gun portee

Advertisement

loading
Need help?

Need help?

Do you have a question about the C15A Lorry and is the answer not in the manual?

Questions and answers

Summary of Contents for Mirror Models C15A Lorry

  • Page 1 CMP C15A Lorry Van Truck Precision plastic model MIRROR Models Ltd. 1/35 Scale Kit No. 35101 The Canadian Military Pattern truck was a class of military truck made in large numbers in Canada during World War II to British Army specifications for use in the armies of the British Commonwealth allies.
  • Page 4 Additional plastic sprue to replace most of resin parts...
  • Page 5 Assembly CMP parts assembly instructions to build up plastic parts provided newly in this kit instead of resin parts supplied earlier (Z19) (Z17) Cut D17, D18 and D19 to length needed Z8+Z9 PE38 Additionally there are many simple single parts included to replace the same in resin these are easy to locate...
  • Page 7 C15A Chevy assembly pins on crossbeams into holes in frame sides x4 back E9x 4 front PE36x8 PE 19x4 PE20x2 PE22 58,8mm PE23x4 wire 0,8mm...
  • Page 8 PE32 PE15 rear front PE32 wire 0,5mm set angle between springs according to their holders do not glue on holders yet!
  • Page 9 glue axles in position mind direction of tire pattern right left...
  • Page 10 wire 0,8mm Cab 12, separate bonnet Cab11 early no air Cab11 later, circular intakes intakes for Chevy PE cover, you can either drill holes and assemble hoses from inside or cover circles Use parts B4 and B5 instead of C9 with fine mesh (not kit contains PE mash for Cab11 only, glue together...
  • Page 11 PE33 push rivets from the back PE33 PE f 1mm wire PE29+30...
  • Page 12 PE39 inside on windshield PE10 Cab11 Cab12 0,5mm wire one-piece mesh and frame split mesh and frame available included in the kit at www.Lzmodels.com PE21 Dry-fit the engine and check right position with cab according to following images, then glue on E1...
  • Page 13 D11 D12 Cut D17, D18 and D19 to length needed PE d PE28 PE26 PE27 PE b...
  • Page 14 PE a PE 11 0,6mm wire PE12+13 PE c 0,8mm wire cut out...
  • Page 15 PE e 0,6mm wire PE37 PE25+24 PE31 Before adding PE7 on PE6 check it fits well between frame beam and mudguard PE a PE 11 PE34...
  • Page 16 PE18...
  • Page 17 2B1 Body PE1, PE5, PE7 optional to replace plastic PE5+7 0,3mm wire Full photo instructions in colors with hi-res images available to download www.mirror-models.com http://mirror-models.com/c15a_assembly.pdf http://mirror-models.com/c15a_marking.pdf...
  • Page 21 Vehicles often painted in olive drab, in desert service in sand yellow with PE plate...
  • Page 24 We hope you have enjoyed our kit. We have improved many things on our next releases, any ejector marks will be avoided as much as possible, and many small details provided now in resin will be also molded in plastic without compromises on detail. Mk I Otter kits is produced in plastic except the resin wheels and transfer case, which is too complicated and could not be made in plastic without losing tiny details If you have experienced missing or damaged part in your kit, contact us directly for replacement at:...