Subscribe to Our Youtube Channel
Related Manuals for GeoVision GV-HD-SDI
Summary of Contents for GeoVision GV-HD-SDI
- Page 1 GV-HD-SDI Camera GV-SDI-BX100 User’s Manual Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
- Page 2 E very effort has been made to ensure that the information in this manual is accurate. 1 0 6 B GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein.
-
Page 3: Table Of Contents
Contents 1. SAFETY PRECAUTIONS AND INSTALLATION CONSIDERATION ......2 2. INTRODUCTION ....................5 3. FEATURES ....................... 6 4. PACKING LIST....................8 5. NAME AND FUNCTION OF EACH PART ............9 5.1 FRONT VIEW....................9 5.2 REAR VIEW....................11 6. INSTALLATION ....................13 6.1 LENS TYPE .................... -
Page 5: Safety Precautions And Installation Consideration
Safety Precautions 1. Safety Precautions and Installation Consideration CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN! CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. - Page 6 Do not install the product in an environment where the humidity is high. Unless the product is waterproof or weatherproof, otherwise it can cause the image quality to be poor. Do not expose to strong light (sun rays), as color filters will be discolored. Do not spill liquid of any kind on the product.
-
Page 7: Introduction
Introduction 2. Introduction This HD-SDI digital image camera uses a high sensitive color Sony 1/2.8” interline transfer Charge Coupled Device (CMOS) image sensor, producing pictures reaching up 900 lines of horizontal resolution. Super ATR-EX technology can achieve the WDR application through the normal image sensor. -
Page 8: Features
3. Features High Resolution Excellent Sensitivity CMOS Sensor provides high resolution High sensitivity, low smear, high reaching up 900 TVL with advanced anti-blooming and high S/N ratio and clear picture quality. ATR-EX (WDR) Digital Noise Reduction (DNR) High-quality ATR-EX (Augmenting Tone 2D DNR, realize the clear image at low Reproduction) or WDR (Wide Dynamic light environment, clear picture quality... - Page 9 Features Lens (C/CS Mount) Extra Connection Support the auto-iris lens by DC type Control the camera easily by (DC-Drive) or fixed iris lens. keyboard/PT Driver via RS485 interface. Image Control OSD (On Screen Display) Setup Menu. Performance: positive/ negative Camera title setup of up to 16 image, mirror function (left/ right), alphanumeric letters.
-
Page 10: Packing List
4. Packing List Check and make sure all the items shown below are included in your product package. If something is missing, contact your dealer as soon as possible. GV-HD-SDI Camera (with Varifocal or Fixed Megapixel Lens) DC 12V Power Adapter Accessories •... -
Page 11: Name And Function Of Each Part
Name and Function of Each Part 5. Name and Function of Each Part 5.1 Front View GV-SDI-BX100-0 (Varifocal Lens) ○ Adjusts the focus of the camera. Focus Screw ○ Zoom Screw Adjusts the zoom of the camera. ○ Auto Iris Connector Plug the iris control cable to the connector. - Page 12 GV-SDI-BX100-1 (Fixed Lens) ○ Adjusts the focus of the camera. Focus Screw ○ Not functional. Auto Iris Connector ○ Mounting base for installing the camera. Mounting Tripod Base...
-
Page 13: Rear View
Name and Function of Each Part 5.2 Rear View Sends video signal (HD-SDI) and connects to the ○ Video-Out terminal: video input terminal of the monitor. ○ Function Input/ Output and RS-485 Interface (Protocol: AUTO/ NATIVE/ PELCO/ LG. Speed: 2.4K/ 4.8K/ 9.6K/ 115.2K BPS) Name Function External Day/ Night input... - Page 14 ○ OSD Button: Name Function Up ( ) Down ( ) Increase Value (＋) (+)/► Decrease Value (－) (-)/◄ Menu Enter or Exit Setup Menu • Up button: Used to move cursor up in the menu screen and to zoom-in. <Note>...
-
Page 15: Installation
Installation 6. Installation 6.1 Lens Type The camera is supplied with a CS-mount lens. You could refer to the below steps only when changing lenses. 6.2 Using Auto Iris Lens Fit the cover of the auto iris connector plug, remove the protective glass cover from the front of the camera, and fasten the auto iris lens by turning it clockwise. -
Page 16: Using A C/Cs-Mount Lens
3. When a lens is mounted, adjustment of the back-focus may sometimes be required. Adjust the lens focus ring when the correct focus cannot be obtained. Back Focus Adjustment (1) Fully open the aperture and set the focus ring to “⎟” (infinity). (2) Loosen the two back-focus screws with L-wrench, and turn the lens mount to focus. - Page 17 Installation 6.3.2 Installing a C Mount Lens Remove the installed lens on the camera, and turn the C-Mount Lens clockwise to install it. And set focus of the camera by loosening the two back-focus screw with an L-wrench. <Note> • C-mount adapter is not supplied with the camera. •...
-
Page 18: Connect To Monitor
6.4 Connect to Monitor Connect the Video-out (HD-SDI) port on the rear panel of the camera to a monitor. As the connecting method varies depending on the instrument, therefore refer to the manual supplied with the instrument for more information. 6.5 Connect the Power Since the camera supports both AC and DC, you may connect an AC 24V, 1000mA adaptor or a DC 12V, 1000mA adaptor. -
Page 19: Connection Layout
Installation 6.6 Connection Layout To connect the keyboard and IR illuminator, follow the instructions shown below: Connecting the IR illuminator 6.6.1 Connecting the Keyboard... - Page 20 PELCO Keyboard (or compatible) Installation RS-422 interface is used for communicating PELCO keyboard. Refer to Fig. 1; connect R+ of the camera to T+ of the PELCO keyboard. Connect R- of the camera to T- of the PELCO keyboard. User could adjust Camera ID via rear panel keys or via remote commands. Protocol, Speed and Parity should only be adjusted via rear panel keys.
-
Page 21: Connecting The Ir Illuminator
Installation 6.6.2 Connecting the IR Illuminator IR Illuminator (Light Sensor) Camera IR Illuminator (Camera Control) <Note> • The camera supports GV-IR LED T2, but it does not support GV-IR LED. GV-IR LED T2 Installation Connect DNO of the camera with the yellow wire of GV-IR LED T2, and connect GND of the camera with the green wire of GV-IR LED T2. - Page 22 Twist the red wire from the GV-IR LED T2 to the power cable (DC 12 V) from the power adapter, which has the gray stripes on it, and twist the black wire from the GV-IR LED T2 to the power cable (ground) from the power adapter, which has the characters on it.
- Page 23 Installation Light Sensor Installation Connect DNI and GND of the camera to the DNI and GND of the IR illuminator (with light sensor). On the OSD menu, select Camera Setup and set Day/Night Mode to EXT. If the operating IR illuminator (with light sensor) is of high voltage (5 V), select Camera Setup and set DI/DO to DI/H : DO/L or DI/H : DO/H (both selections are okay).
- Page 24 IR Illuminator Installation Connect DNI and GND of the camera to the DNI and GND of the IR Illuminator (of camera control). To automatically switching between night and day modes: • If the operating IR illuminator (of camera control) is of high voltage (5 V), on the OSD menu, select Camera Setup and set Day/Night Mode to AUTO (default value).
-
Page 25: Operation
Operation 7. Operation Mount the camera on the mounting bracket by using the hole on the top or bottom of the camera, and by using the enclosed mounting block, secured by 2 screws. Connect the video output to the monitor or other video device via a 75 Ohms type coaxial cable. -
Page 26: System Setup
8. System Setup 8.1 OSD (On Screen Display) Main Menu Display MAIN MENU V1.00 2012-04-03 PROFILE STANDARD CAMERA SETUP ─ PRIVACY MASK ─ DISPLAY INFO ─ COMMUNICATION ─ SYSTEM INFO ─ DEFAULT Main Menu Setup In order to display the setup menu on the screen, set the menu command or •... -
Page 27: Sub Menu Description
System Setup 8.2 Sub Menu Description CAMERA SETUP LENS DI/DO DI/L : DO/H EXPOSURE ─ DAY/NIGHT ─ WHITE BALANCE ─ EFFET ─ RETURN 8.2.1 CAMERA Setup The box camera supports both DC-type and Manual-type lenses. DC-type lens application is suggested for best quality and performance. 8.2.2 EXPOSURE Setup EXPOSURE ATR-EX... -
Page 28: Day/Night Setup
<Note> • When images appear fuzzy, select 1/60 for the country of NTSC (60 Hz) and 1/50 for the country of PAL (50 Hz). BLC ON/OFF (Default Setup: OFF). AGC modes: OFF / LOW / MID / MID.HIGH / HIGHT DNR Level: OFF / 1~5 step. -
Page 29: White Balance Setup
System Setup 5. B/W: Set to ON for B/W images and OFF for Color images. 6. DEFAULT: Return to day/night default setup. 7. RETURN: Return to previous status. <Note> • When D/N are set to AUTO, the value will be automatically adjusted regarding to the circumstances. -
Page 30: Effect Setup
8.2.5 EFFECT Setup EFFECT POSI/NEGA POSI MIRROR DEFAULT RETURN 1. POSI/ NEGA: Images can be set to POSI (Positive Image) or NEGA (Negative Image). (Default Setup: POSI). 2. Four Types of MIRROR Mode: OFF/ HORIZONTAL/ VERTICAL/ ROTATE (Default Setup: OFF). 3. - Page 31 System Setup 2. MASK: Set MASK to “ON”, MASK AREA becomes available for setup and is shown on the monitor (Default Setup: OFF). 3. START X: Horizontal start position (0~600). 4. END X: Horizontal end position (40~640). 5. START Y: Vertical start position (0~330). 6.
-
Page 32: Display Info Setup
8.2.7 DISPLAY INFO Setup DISPLAY INFO DISPLAY ─ COLOR ─ RESOLUTION 1080P30 RETURN 1. DISPLAY: Under this item user may decide whether to reveal or hide TITLE SET / TITLE DISPLAY / TITLE POSITION / ID DISPLAY / ID POSITION. For more setup details on display, follow the setup guide shown below: DISPLAY TITLE... - Page 33 System Setup 2. COLOR Setup: COLOR BRIGHTNESS CONTRAST SHARPNESS GAMMA DEFAULT RETURN (1) BRIGHTNESS: Video brightness level setup (0~255). (2) CONTRAST: Video contrast level setup (0~255). (3) SHARPNESS: Video sharpness level setup (0~255). (4) HUE: Video hue level setup (0~255). (5) GAMMA: Video gamma setup (0~3).
-
Page 34: Communication Setup
8.2.8 COMMUNICATION Setup COMMUNICATION CAMERA ID SPEED 2400 DEFAULT RETURN 1. CAMERA ID: ID setup 0~255 (Default Setup: 1). 2. SPEED: Baud Rate setup 2400, 4800 , 9600 , 115200 (Default Setup: 2400). 3. Refer to “6. INSTALLATION” for more information on Communication. 8.2.9 DEFAULT Setup MAIN MENU V1.00 2012-04-03... -
Page 35: Specifications
Specifications 9 . Specifications 5 0 9 B Camera GV-SDI-BX100-0 GV-SDI-BX100-1 Image Sensor 1/2.8” type CMOS Picture Elements 1920 (H) x 1080 (V) Color 0.5 Lux at F/1.4 0.5 Lux at F/1.5 Min. 0.1 Lux at F/1.4 0.1 Lux at F/1.5 Illumination IR On 0 Lux... - Page 36 General Operating Temperature -10 ~ 60 / 14 ~ 140 ℃ ℃ ℉ ℉ Power Source DC12V / AC24V Max. Power 6.6 W Consumption Video Output 3G HD-SDI / 800mV / 75 Ohms Remote Control RS-485 / RS-422 Protocol PELCO D&P All specifications are subject to change without notice.
- Page 37 Specifications...
- Page 38 2012/07 English The GeoVision logo and GV series products are trademarks of GeoVision, Inc. © 2012 GeoVision, Inc. All rights reserved. SDIBX100-B-EN All GeoVision Products are manufactured in Taiwan.
Need help?
Do you have a question about the GV-HD-SDI and is the answer not in the manual?
Questions and answers