Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for DARK HUNTER NB25-7MHR
- Page 1 NB25-7MHR Fusion IR Full HD MFZ IP Camera...
- Page 2 ’ ’ CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
- Page 3 ’ ’ Regulatory Notice This equipment has been tested and found to comply with limits for a Class of digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
-
Page 4: Table Of Contents
’ ’ Contents Introduction ..............................5 1.1. Overview ............................... 5 1.2. Features & Specification ........................6 1.2.1. s ............................6 n ..........................6 1.3. Applications of IP Camera ........................8 Product Description ............................9 2.1. Contents ..............................9 2.2. Camera mount configuration......................... 9 2.3. -
Page 5: Introduction
PC or smart device. Real time 2-way communication is available through bidirectional audio communication feature. Dark Hunter technology is the most optimized solution for indoor and outdoor surveillance in low-light conditions by using superior CMOS sensor with low-light sensitivity ISP sensor. -
Page 6: Features & Specification
Digital PTZ, video crop Analog video output (CVBS) Built-in standard PoE Two-way audio communication Dark Hunter + Super IR LED Compact design & Easy installation Vandal proof, Weather proof (IP66) Camera Image sensor Progressive scan 1/3 inch CMOS 2.47M pixels(Total) - Page 7 ’ ’ Mirror H / V / Rotate DEFOG ON / OFF BUILT IN Internally(English) Super IR LED Video Compression method Simultaneous Dual Codec (H.264MP / MJPEG) Resolution 1,920 x 1,080@30fps - 5 simultaneous video profiles Multi-Profile Streaming - Select the codec type, resolution and frame rates for each profile. Intelligent Bit-Rate Control Hybrid Bit Rate control (VBR+CBR) Digital PTZ &...
-
Page 8: Applications Of Ip Camera
’ ’ Alarm Triggers Motion Detection + Sensor Input + Audio Detection Alarm Events Video file upload(FTP), Still Image transmission(Email), Relay output Alarm Buffer (Audio/Video) Configurable Pre-alarm (5~15 sec) & Post-alarm (10~60 sec) Operating Environment, Power, Dimensions Operating Temperature -10C ~ 50C Operation Humidity 8 ~ 80% RH Power... -
Page 9: Product Description
’ 2. Product Description 2.1. Contents The product package contains followings: Contents Description Remarks IP Camera NB25-7MHR main unit Screws Accessories L-type wrench, CVBS Cable Guide pattern Software & User’s Guide Default built in standard PoE module 12V DC Adaptor Power Adaptor (IEEE802.3af) -
Page 10: Product Preview
IP-Installer CMS Software (NVR) PC software to view and record the A/V streaming data transmitted from PC software to allocate an IP NB25-7MHR IP camera. address to the IP Camera (Simultaneous support of up to 64 IP cameras) 2.4. Physical description 2.4.1. -
Page 11: Dimension
’ ’ 2.4.2. Dimension Unit: mm Figure 2-2. Dimension 2.4.3. External Connector Sensor Input (white(+), Red(-)) Relay Output (Black(+), Yellow(-)) Line Output Network (LAN) Power Mic/Line Input Figure 2-3. Connector for external connection 2.4.4. Factory Default Switch Factory default switch is provided for returning the IP camera to factory default state. The factory default switch can be found by opening the lower body cap of the camera. -
Page 12: Functional Description
’ ’ 2. Safe Removal of Micro-SD Card : Press the switch for 1 second to unmount Micro-SD Card for safe removal. Video Output (CVBS) Factory Default Switch/ Micro SD Card Eject Micro SD Card Slot Figure 2-4. Factory Default switch and Micro-SD Card slot 2.5. - Page 13 ’ ’ Relay Output Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A.
-
Page 14: On Site Installation
’ ’ 3. On Site Installation Use cables and conduits that are suitable for the installation and that are compliant to IP66. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. - Page 15 ’ ’ Precautions – Outdoor Installation : Leaking expected at connected cable on outdoor installation. Use the waterproof rubber tape winding up on cable connection as following picture. 1) Connect cables. 2) Winding rubber tape with half overlay on external cable jacket (A) and cable connection. The tape material butyl rubber is extended more than double size.
-
Page 16: Getting Started
’ ’ 4. Getting Started 4.1. PC Requirement Audio/Video streaming data received from IP Camera can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Minimum Requirement Recommended Specification Intel Core i3 3Ghz Intel Core i7 Main Memory Operating System... -
Page 17: Install Ip Installer And Set Ip Parameters On Ip Camera
’ ’ 4.2.2. Install IP installer and set IP parameters on IP Camera 1. Please insert the Setup CD into your CD-ROM drive, and then please setup Figure 4-2-1. IP Installer Setup 1 2. Please click ‘Install’ button to begin the Installation. Figure 4-2-2. - Page 18 ’ ’ 4. XNET IP Installer program is automatically launched like below right after the program installation. Figure 4-2-4. IP Installer Start box 5. Select the camera of which you wish to change the IP address and click (Set IP Address) button to bring up the following box in Figure 4-2-5.
- Page 19 ’ ’ 6. When you enter the IP address and click Set button, the box shown in Figure 4-2-5 will appear. Figure 4-2-6. Select Network Adapter Box 7. Select the adapter and click ‘Select’ button to change the IP address of the camera. Rev.1.4...
-
Page 20: Remote Video Connection To Ip Camera
’ ’ 4.2.3. Remote video connection to IP Camera 1. Connection through Web Viewer Web Viewer offers the simplest way of video connection to IP Camera. For video connection, enter the IP address of IP Camera in the URL window of Internet Explorer as: Can be omitted the default [e.g.] Port 80 port of 80... -
Page 21: Additional Settings Through Connection To The Admin Page
’ ’ 2. Connection through NVR2 NVR2 is a multi-channel CMS program for IP camera or Video server. Install NVR2 on remote PC to connect to these products. It is needed to assign connection information to NVR2 program before connection. Details for the NVR2 can be found in [NVR2 User’s Guide]. Figure 4-4. -
Page 22: Troubleshooting
’ ’ 5. Troubleshooting 5.1. No power In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both IP camera and LAN switch support standard PoE (IEEE 802.3af) ... -
Page 23: Windows 7
’ ’ 5.3. Windows 7 Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting”... -
Page 24: Technical Assistance
’ ’ 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service, please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. -
Page 25: Appendix A - Important Notice In Exchanging Sd Card (Micro Sd)
’ ’ Appendix A – Important Notice in Exchanging SD Card (Micro SD) SD Card is a non-volatile memory device for storing video and audio data on the product. Continued writing to the SD Card will cause wear-off of the memory cell. When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card.