Beryllium, they should be carefully collected with the use of a supplied adhesive tape and sealed in a zip- top bag to be returned with the tweeter. For further information, please contact Focal-JMlab directly: beryllium@focal-fr.com English...
If not followed correctly any fault observed, may not be covered by the guarantee. To confirm Focal-Jmlab’s guarantee, please register on line on our website: http://register.focal-fr.com, or send the guarantee back to us within 10 days of purchase. English...
Page 6
• Fig. 1 • Fig. 2 and 3 • Fig. 4 and 5 English...
Tweeters installation Location in n°5, 6 and 7 kits) contains all Flush mounting (highly recom- TBe tweeter has been designed for necessary functionalities to optimize mended) flush mounting (recommended) the tweeter setting, according to its Best results will be obtained by a or surface mounting installation, location and vehicle acoustic.
Woofers / midranges mounting Woofer location Midranges location the metal-work of the vehicle, Plain Woofers positioned ideally high 3“ midrange (n°7 Utopia Be kit) is Chant soaks-up vibrations as well in the doors (fig. 1, A), produce made to be install near tweeter, on as acoustic reflections.
Page 11
Woofers / midranges mounting Woofer Midrange Set up fixing clips to accept the Set up fixing clips to accept the fixing screws later (fig.1). Set up the fixing screws later. (fig.1). Set up the fixing ring, ensuring it lines-up with fixing ring, ensuring it lines-up with the fixing clip positions.Fix the foam the fixing clip positions.
N° 5 and N°6 Crossblock wiring N° 5, 6 Crossblock can be connected • Biwiring: two pairs of cables from • Biamplification: crossblock is po- to amplifier according to 3 ways: amplifier to woofer section and twee- wered separately from woofer and tweeter amplifiers (fig.
N°7 Crossblock wiring • Monowiring: one cable per spea- • Biamplification: Crossblock is po • Warning: ensure both speaker is ker’s group (left/right fig.1 ). wered separately from woofer and wired in phase, thus polarities are midrange/tweeter amplifiers (fig. 3). respected “+”...
Crossblock installation Warning Mounting When using Crossblock in bi- To access to Crossover fixing holes, remove the fixing screws (fig. 2). wiring or biamplification, you must remove the 4 jumpers Fix Crossblock with the four screws backside, if you don’t, you can provided on a perfectly flat area (fig.
N°5 and N°6 Crossblock settings N°5/N°6 Crossblock is an exclusive S1 setting (Low-pass) S3 setting (Hi-pass) high technology crossover offering This setting changes the low-pass This setting changes the hi-pass 4480 different filtering combinations frequency value (12dB/octave). “1” frequency value (12 dB/octave). to adapt kit’s characteristics to car’s refers to the higher value and “10”...
N°7 Crossblock settings N°7 Crossblock is an exclusive high S1 setting S3 setting (Level) technology crossover offering 4480 It combines two settings in one. Midrange level setting according to different filtering combinations to changes low-pass crossover 8 values, 1dB per step. Step “1” adapt kit’s characteristics to car’s frequency values...
Utopia Be Active Kit Active kits (N°5, 6, 7) are provided N°5 / N°6 active kits wiring N°7 active kit wiring without Crossblock crossover in Wire tweeter and woofer on active Wire tweeter and woofer on active order to allow amplification with crossover, then wire crossover to crossover, then wire crossover to active crossover.
Subwoofers installation Utopia Be line subwoofers are Subwoofers installation 21 WX mounting tailored to be installed in small Each subwoofer kit comes complete Fix the foam gasket to the back enclosures to allow their installation with its fixing kit and foam gasket. of drive unit chassis, then fix with in the front of the vehicle.
Box enclosure mounting The correct acoustic load, normally Sealed box enclosure Bass-reflex enclosure the type of enclosure and volume Utopia Be subwoofers have been Bass-reflex enclosure suits to 21 made available to the subwoofer, is carefully optimised to work in sealed WX subwoofer under conditions.
Kits speciÄ cations N° 5 / N° 5 Active N° 6 / N° 6 Active N° 7 / N° 7 Active Maximum power 150W 200W 200W Nominal power 100W 100W 89.5dB 91.5dB 89dB Sensitivity Frequency response (± 3 dB) 75Hz to 40kHz 66Hz to 40kHz 55Hz to 40kHz Nominal impedance...
Dimensions Unit: mm • Tweeter TBe - Kit N°5, N°6, N°7 & Active Unit: mm • Midrange/Médium 3 W2 Be - Kit N°7 & N°7 Active Unit: mm • Woofer 5 W2 Be - Kit N°5 & N°5 Active Unit: mm •...
Page 32
Dimensions Unit: mm • Woofer 6 W3 Be - Kit N°7 & N°7 Active Unit: mm • Subwoofer 13 WS Be Unit: mm • Subwoofer 21 WX Be...
International guarantee The Focal guarantee only applies if this page is returned to us within 10 days of purchase, to the following address: Focal-JMlab - BP 374 - 108, rue de l’Avenir - 42353 La Talaudière cedex - FRANCE Model:...
Page 35
Garantie France Pour validation de la garantie Focal, merci de nous retourner cette page dans les 10 jours, à l’adresse suivante : Focal-JMlab - BP 374 - 108, rue de l’Avenir - 42353 La Talaudière cedex - FRANCE Modèle : N°...