Related Manuals for Lassco Wizer Spinnit EBM-S
Summary of Contents for Lassco Wizer Spinnit EBM-S
- Page 1 Lassco Spinnit EBM-S Paper Drill User's Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 Serial Number: Date of Purchase: Dealer: Address: Before operating this equipment, please read these instructions completely and keep these operating Telephone Number: instructions for future reference. 485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com info@lasscowizer.com...
-
Page 3: Table Of Contents
Table Of Contents Introduction Introduction............... Page 02 Shipping Damage Inspection..........Page 02 Safety Information Safety Instructions............Page 03 Warning Labels..............Page 03 Setting Up Your Machine Loose Materials Inventory..........Page 04 Back Gauge Assembly............Page 05 Stop Collars and Paper Side Stop........Page 05 Chip Bag................ -
Page 4: Introduction
Introduction Introduction Thank you for your purchase of the Spinnit EBM-S Paper Drill. Lassco-Wizer has been designing and manufacturing proven performance equipment for the graphic arts, office, screen printing, sign, awards and engraving industries for over 60 years. We ask that you take a moment to fill in the serial number and other information on the front cover of this manual. -
Page 5: Safety Information
Safety Information Safety Instructions All operators must read and understand the Users Manual and all other safety instruc- tions before using this equipment. If after reading the manual you are still uncertain about use, please contact a Service Technician for assistance. If you need contact information for a Service Technician nearest you please call 585-436-1934. -
Page 6: Setting Up Your Machine
Setting Up Your Machine Loose Materials Inventory Remove and inspect the following items: EBMS-115A: Backgauge Assembly (1) EBM-10: Drill Block (1) Hollow Drill BIt (1) Spin-Eze: EBM2-1048: Chip Bag (1) Drill Bit Lubricant (1) This item comes installed This item comes installed CC-2: Chip Clearer (1) EBM-32: HEX-18:... -
Page 7: Back Gauge Assembly
Setting Up Your Machine Back Gauge Assembly Attach the Backguage (EBMS-115A) to the Table by hooking Step #1 the left end over the Side Iron (FM4-4003) on the side as shown in the accompanying pictures. Align both ends of the backgauge using the Table Scales so that it is squared correctly. -
Page 8: Chip Bag
Setting Up Your Machine Chip Bag Attach the Chip Bag (EBM2-1048) as shown by stretching Step #4 the open end over the top hook of the Chip Chute (EBM2- 110A). Continue fitting it around the entire edge of the Chip Chute making sure it is snug. -
Page 9: Operating Instructions
Operating Instructions Drill bit Removal and Installation Remove the hole guard which is attached to the Chuck. This Step #1 is done by grasping the bent end and sliding the guard off. Using the Chuck Release Key (EBM-32), insert the tapered Step #2 end facing down into the chuck hole. -
Page 10: Leveling The Drill Bits
Operating Instructions Leveling The Drill Bits To level the drill bits to the Table, first loosen the Step #6: Leveling Knob on the right hand side of the machine as shown. Pull down on the Handle to raise the Table until the hollow drill bit is just touching the Drill Strip (EBM2-1034). -
Page 11: Clearing The Chips
Tips On Drilling Use a sharp bit at all times...Using a drill bit sharpener (Lassco-WIzer MS-1 recom- mended), sharpen your drill bits regularly. Apply light pressure when sharpening. Too much pressure may cause flaring of the tip. (Once a drill bit has a flared tip, it becomes defective.) -
Page 12: Maintenance
Maintenance Every 6 Months Remove back panel and lubricate the lift pin with a good grade of light machine oil. Lubricate Note: Refer to your Trouble Shooting Guide for problem solving CAUTION: KEEP FINGERS FROM BETWEEN LIFT COMPONENTS. OBSERVE ALL SAFETY PRECAUTIONS DURING THE PREVENTATIVE MAINTENANCE OF THIS MACHINE. -
Page 13: Trouble Shooting Guide
Trouble Shooting Guide Problem Cause Correction Drill bit not concentric. Foreign material in chuck or in Inspect and clean. drill plug. Drill bit is bent. Replace drill bit. Drill bit not seated in chuck Reinsert drill bit correctly. properly. Chuck is not tight to spindle. Tighten set screw. -
Page 14: Parts Diagrams
Parts Diagrams Front, Back, and Side View See Parts List on Page 14 Page 12... -
Page 15: Interior Front And Back
Parts Diagrams Interiror Front and Back See Parts List on Page 14 Page 13... -
Page 16: Parts List
Parts Diagrams Parts List EZ-108A: Handle Assembly FM5-5006: Rocker Switch (On/Off) EZ-117A: Shroud Assembly FM5-5003: Chuck FM5-5011: Chuck Release Guard Hollow Drill Bit EBM2-0111A: Pressure Foot Assembly 3S-14: Table Scales EBMS-114A: Table Assembly EZ-1025: Base EBM-44A: Channel Guard FM4-4007: Table Height Adjustment Knob EZ-1034: Table Guide EBM2-1047: Chip Bag Bracket EBM-10: Drill Block...