Thompson roc 4306 Operation Manual

The ROC 4306 is a universal remote control (4 in 1). It can replace 4 remote controls thanks to its
4 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette
recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT),
amplifiers and other audio equipment provided they are controlled by infra red signals.
This remote control has been factory programmed to allow you to use it immediately with the
majority of Thomson Group devices.We therefore advise you to try it before beginning to program it.
If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual.
But first, install 2 batteries (AAA) in the remote control.
Keep these instructions and the separate list of codes in a safe place so that you can later reprogram

your remote control.

1 - Description of keys
1  I ndicatorlamp:theredindicatorlamplightsupwhen
anykeyispressed.
2 B:On/Standby.
3  R emotecontrolmode
SelectsdevicetocontrolTV,DVD,VCR,...
4 B(Play):play*.
5 F(FF):fastforward*.
6  L (STOP):stopplayback*.
7 K(Pause):stopsonanimage*.
8  I (EXIT):teletextOffinTVmode.
SHIFTandEXIT:turnsoffthemenuofthe
selectedproduct.
9  V OL-/VOL+increases(+)ordecreases(-)the
volumeoftheTVset.
    S HIFTandVOL-/VOL+alsoallowsyouto
navigatethemenushorizontally.
1 0  S :programmestheremotecontrol.
    S HIFT:activatesthesecondarykeyfeatures
(indicationsinblue).
1 1  N umber keys 0 to 9:thesekeyshavethesame
functionsasthoseofyouroriginalremoteandare
alsousedtoenterthecodesfordifferentproducts.
1 2  P ressthiskeyfirstbeforeyoutypeinthe2-digit
channelnumber(exceptforThomsongroup
products).
1 3  A V:forselectinganexternalsource(SCART).
1 4 c:switchestheTVsoundoff.
  SHIFTandOK:confirmsaselection.
1 5  P ROG+,PROG-:programmeszappingbutton
(receivedbythetelevisionsetorthesatellite
receiver);usetoscrollverticallythroughmenus
SHIFTandPROG+/PROG-alsoallowyouto
navigatethemenusvertically.
1 6  a (MENU):teletextOn/OffinTVmode.
    S HIFTandMENU:turnsonthemenuofthe
selectedproducts.
1 7  M (RECORD):torecord.
1 8  G (REW):goesbackwardoradvancesforward*.
*Thecolouredbuttonscanbeusedtoselectcategories
whenteletextisactivated,andspecificfunctions
dependingonthemake.
2 - Testing the remote control
before programming
1.  T urnonthedevicethatyouwishtocontrol.
2.  P ressthekeycorresponding(3)tothetypeofdevice
tocontrol:
 TV:televisionset,
VCR/DVD:videocassetterecorder,DVDplayer,

 DVB-T:DVBTreceiver,
 SAT:satellite.
3.  P ointtheremotecontrolatthedeviceyouwishto
controlandtrytoturnitoffusingthe B (2)key.
  I fthedevicedoesnotturnoff,youmustprogramthe
remotecontrolusingoneofthemethodsA, B,Cor
Dasdescribedbelow.
01_ROC4306_GB.indd 1

3 - Programming
the remote control
Method A – Fast programming with
1-digit subcode
Before you start programming, you must find the subcode of
the set to be controlled.
Refer to the list provided with these instructions, page I of the
codes.
1  S witchonthesetyouwanttocontrol.
2.  H old down the S (10) key  until the red indicator
lamp (1) remains lit (the indicator light remains on
forafewsecondstogiveyouthetimetoproceedwith
the following steps.The indicator lamp flashes when
thistimeisalmostup,andthengoesoff).
3.  P ress the key (3) that corresponds to the type of
equipmentyouwanttocontrol:
  T V:televisionset,
 VCR/DVD:videocassetterecorder,DVDplayer,
 DVB-T:DVBTreceiver,
SAT:satellite.

4.  W hiletheindicatorislit,typeinthesubcode(example:
1forThomson).
5.  D irecttheremotecontroltowardsthesetandtryto
switchitoffbypressingthe B (2)key.
6.  I f the set you want to control switches off, press
c(14)tomemorisethesubcode.
7.  I f the product doesn't turn off, press the B  (2) key
repeatedlyuntilthesetswitchesoff. W aitapproximately
one second between key presses to give the red
indicator lamp (1) enough time to go off and
lightupagain.Thiswillallowyoutoseewhetherthe
productrespondsornot.
8.  I mmediately upon the switching-off of the set to be
controlled,pressc(14)tostorethesubcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television set),
begin by entering the code that corresponds to the product you
want to programme (a 4-digit code that you will find in the code
booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands. Check your remote control for proper functioning by
performing the test described on page 3.
  
8/12/06 9:50:20